Consider the following transfer function: (0.2s + 1)(0.5s + 3) 0.5s2 + 0.2s + 4.5 G(s) = %3D In the asymptotic approximation of this transfer function's Bode diagram, what are the slopes of the lines in the magnitude and phase plots at the frequency 10 rad/s? -40 dB/dec and 0° /dec -20 dB/dec and 0° /dec 0 dB/dec and -45° /dec O dB/dec and-90°/dec O dB/dec and 0°/dec

Consider the following transfer function: (0.2s + 1)(0.5s + 3) 0.5s2 + 0.2s + 4.5 G(s) = %3D In the asymptotic approximation of this transfer function's Bode diagram, what are the slopes of the lines in the magnitude and phase plots at the frequency 10 rad/s? -40 dB/dec and 0° /dec -20 dB/dec and 0° /dec 0 dB/dec and -45° /dec O dB/dec and-90°/dec O dB/dec and 0°/dec

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A series RLC circuit is formed using component values R=100 and L=1.5 mH, together with a source that provides a sinusoidal voltage Vs (t). If the quality factor in resonance condition is Q0 = 7, determine: a) the magnitude of the impedance at 500 Mrad s-1b) the current that circulates if vs (t) = 2,5V cos (425 ×10 6t) Note: Vent (input voltage). Vsal (output voltage)
A mass-spring-damper system is shown below and its transfer function is given. Find the spring constant, mass, and damper constant k,m,c of the system according to the Bode diagram given below. Reminder: The starting point of the red line corresponds to -26dB. ζ=0.32. The frequency corresponding to the sloping peak of the red line ω=ωn =3.2
753. For the transfer function (TF) 2s/(s+3) and resulting Bode Plot, calculate the gains (dB) at the corner, one decade below, and one decade above. Also calculate the phase (deg) of the TF at the same three frequencies. Last answer is w_corner (rad/sec) Find: gdB_corner_f, gdB_low_f, gdB_high_f, phase_corner_f(deg), phase_low_f(deg), phase_high_f(deg), w_corner(rad/sec)
Given the following circuit: a) Derive the transfer function for v_capacitor(s)/Vin (s) b) Find the damping ratio of the system given the component values in the figure c) Find the resonance frequency of the circuit
Draw the magnitude and phase Bode plots for the following transfer functions. use the asymptotic approximations H(s)=50(s+20)/(s+200)(s+2000) H(s)=10s(s+500)/(s+10)(s+100) H(s)10^8/s(s+100)(s+10000) H(s)=10^4(s+100)/s(s+10)(s+1000)
a-) Determine the zero and poles of the circuit given above by obtaining the transfer function as H(s) = Vout(s) / Vin(s) (Assume the initial values of the energy storage elements are zero). b-) Using the transfer function obtained in the previous option, draw the approximate total amplitude response graph of this function with the help of BODE curves. In these drawings, the total amplitude response equations of the system, the amplitude response graphs of each component in these equations, and the frequency values in the total graphs drawn should be included.
Sketch a Bode plot, using straight-line approximation, for the range of frequencies from 1 Hz up to 1 MHz. Include magnitude and phase plots. put magnitude in dB. Graph should include: -how fast the transfer function “rolls off” below the cut-off frequency (in dB/decade) -the phase and amplitude for the three frequencies: ω = ωC, ω = 10∗ωC, ω = 0.1∗ωC fc = 500 Hz ωC = 2π(fc) This is for a passive high pass filter (single resistor, single capacitor)
Draw the Bode Diagram for the system given the transfer function below. Use the Bode diagram to interpret the stability of the system. ( I would appreciate it if you could help quickly :) )
A series RLC Circuit, shown in the Figure, is energized by a 100 V/4 kHz AC supply.The capacitance of the circuit is adjusted until resonance occurs, producing a qualityfactor of 50. Given that the impedance at the half-power points is 70.71 ohms, determine a. the power dissipated at resonance b. the inductance at resonance c. the lower -3dB frequency and the magnitude of the current at the upper -3dB frequency
Start by finding the Thévenin equivalent circuit seen by the capacitance. Then, sketch the magnitude of the transfer function H(jw) = Vout/Vin. What is the value of the cutoff frequency?
a-) Transfer in the form of H(s) = Vout(s) / Vin(s) of the circuit given above Determine the zero and poles by obtaining the function of the energy storage elements. accept initial values b-) By using the transfer function you obtained in the previous option, Plot the approximate total amplitude response graph with the help of BODE curves. In these drawings the total amplitude response equations of the system, the amplitude of each component in these equations response graphs and the total graphs drawn should include frequency values.
referring to the attached equation, 1.Determine the breakpoints of the above function. 2.Choose the magnitude, phase angles and asymptotes of eachbreakpoint. 3.Sketch the bode plots of the transfer function. Indicate on your plot allthe corner frequencies, slopes of sloping line, gains of sloping linesand gain, and phase levels on zero slope lines.