Consider the given circuit. n 12+ R www www Rw Z.p a Le Vbn b Rw ww B For the balanced three-phase system, it is determined that 100 W is lost in each wire. If the phase voltage of the source is 400 V, and the load draws 10.00 kW at a lagging PF of 0.83, determine the wire resistance Rw (Round the final answer to three decimal places.) The value of the wire resistance Rwis Ω.

Consider the given circuit. n 12+ R www www Rw Z.p a Le Vbn b Rw ww B For the balanced three-phase system, it is determined that 100 W is lost in each wire. If the phase voltage of the source is 400 V, and the load draws 10.00 kW at a lagging PF of 0.83, determine the wire resistance Rw (Round the final answer to three decimal places.) The value of the wire resistance Rwis Ω.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.50P: Consider the balanced three-phase system shown in Figure 2.34. Deter mine v1(t) and i2(t). Assume...

See similar textbooks

Similar questions

Consider the balanced three-phase system shown in Figure 2.34. Deter mine v1(t) and i2(t). Assume positive phase sequence.
In the figure, the circuit is given as VRS =√3 . 60V and Zy = 6 + j8. Find the value of C to be connected in order to make the power drawn from the system in a phase 1, to make the load current 1, and to make cos(φ) 1.
The power system insulation problem involves a. Capacitance of earth and subsequent grounding b. Selection of basic insulation level of system equipment c. Determination of single phase line insulation d. Determination of three phase line insulation Clear my choice
A three-phase system has balanced conditions so that the per-phase circuit representation can be used as shown in Figure 1 Select the turns ratio of the step-up and step-down transformers that the system operates with an efficiency greater than 99 percent. Moreover, find the complex power (received or given) of all components in the circuit and the V1 and V2 voltages. The load voltage is specified as 4 kV rms, and the load impedance is 4/3 ohm. ..
A balanced, three-phase, positive sequence, with grounded neutral source, supplies power to a balanced delta connected load. For the system, additional information are as follows: Vbc = 443 cis 191 degrees volts; and Ic = 10.5 cis99 degrees amperes What is the value of the total real power of the delta load in watts? ANSWER QUICKLY NO DIAGRM NEEDED
For an AC power distribution circuit, the line voltage is 480V and the line current is 53A. The circuit is balanced Wye or star connected. a. What is the phase voltage measured to the neutral leg?b. What is the phase current for each leg?c. What is the total apparent power drawn by the circuit?d. What is the total apparent power drawn by each phase of the circuit?e. If the circuit has a Power Factor of 85%, what is the total real power drawn from the circuit?
3) State the relation between line and phase values of voltage and current for 3-phase STAR connected load .state the equation for active, reactive power consumed by 3-phase load.
In the circuit of figure shown in the next slide, threeimpedances are 12 – j10 ohms, 10 + j20 ohms, and 15 + j0ohms, connected between conductors a, b, c and the neutral“n” of a balanced 230 volts, 60 hertz, 3 phase, 4 wire, ABCsystem. Using Van as the reference vector, determine:a. Current in each impedanceb. Neutral current Inc. Readings of wattmeters W1, W2, & W3d. Power in each impedance ..
Solve all parts or will dislike For the following circuit, the source voltage phasor is: ?s = 250.7∠ -4.16 deg ? a) Calculate the equivalent workshop impedanceb) Deduce the value of the phasor ?c) Calculate the voltage at the workshop terminals using the ohm lawd) Calculate the voltage at the workshop terminals using the law of loopse) Determine the real and reactive powers of the workshop and its power factor solve all parts or will dislike
What is the main direct cause of reactive power in AC system?A. Resistance of transmission linesB. Inductance and capacitance in the loadsC. Ideal transformer connected in the systemD. Power produced by generator2. “Reactive power in a system is dissipated generally as thermal energy?”A. TRUEB. FALSE3. Which of the following statements are correct for three phase circuit:A. Sum of all the three phase currents is zero in unbalanced networkB. Total power transfer to load is constant with timeC. Neutral conductor is same size in terms of material used as in single phase conductorsD. Net apparent power consumed is equal to real power
In a balanced three-phase system, Vbn = 277≮30º. If you could measure the magnitude and angle of Vac,what would it be equal to?
Which termination would result to a phase change of 180 degrees at the load if Zo = 100 ohm? a. 50 ohm b. short circuit c. 75 ohm d. all of these What is the purpose of impedance matching? a. maximum return loss b. maximum SWR c. maximum load power d. maximum reflection A short piece of transmission line that may be open or shorted and used for impedance matching purposes. a. converter b. decoder c. stub d. transformer