Consider the given figure. 20 kips 24 kips 10 kips 2010 A B K 6 @ 20'= 120' Using the influence lines, determine the maximum live load force produced by the 54-kip truck as it transverses the bridge, which consists of two trusses. Assume the truck moves along the center of the roadway so that one-half of the truck load is carried by each truss. Assume the truck can travel in either direction. The maximum live load compression (FAL) in bar is The maximum live load compression (FKJ) in bar is The maximum live load tension (FKJ) in bar is kips. 20' kips. kips.

Consider the given figure. 20 kips 24 kips 10 kips 2010 A B K 6 @ 20'= 120' Using the influence lines, determine the maximum live load force produced by the 54-kip truck as it transverses the bridge, which consists of two trusses. Assume the truck moves along the center of the roadway so that one-half of the truck load is carried by each truss. Assume the truck can travel in either direction. The maximum live load compression (FAL) in bar is The maximum live load compression (FKJ) in bar is The maximum live load tension (FKJ) in bar is kips. 20' kips. kips.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A reinforced concrete beam has a width of 400mm and an effective depth of 600mm. It is reinforced for tension with 4-28mm rebars. F'c = 20.7MP and Fy = 414.6MPa. 7. Determine the ultimate moment capacity. a 484.76KN.m b. 448.67KN.m 8. Determine the percent increase in ultimate b. 34.4% a. 25.1% c. 487.46KN.m d. 446.87KN.m moment if depth is increase to 700mm. c. 18.98% 15.68%
For the section shown in Fig.1 if the applied moment =200 KN.m, n=12, b =841 mm, d=500 mm, As =1814 mm2, bw=250 mm, and hf =101mm. Find the moment of compression area about x-x axis
QUESTION-1: Draw the bending moment diagram of the system under the influence of external loads below. Calculate the vertical displacement value at the intersection of the horizontal beam and vertical column member? (EI= 50000kNm2)
6. The steel gate 2.61m square of thickness 36.1mm is to be lifted by a frictionless pulley. The coefficient of friction between the dam and plate is 0.216 ,calculate the minimum force required to lift the gate if it is fully submerged to a depth of 1.61m. Use specific gravity of steel 8.0 PLEASE ANSWER THIS ASAP!!!
A 2m long, 0.5m diameter log (sp. gravity of 0.9) divides water as shown. Compute for the vertical reaction at point A in KN. CHOICES a.) 5.8 b.) 8.5 c.) 0.85 d.) 0.58
In the cage system below; It is under the effect of a P=250 kN load acting at an angle of θ=75° from the point C. Calculate the horizontal displacement (cm) to the right at point C. (E=2000 kN/cm2 and A=50 cm2 shall be taken for all rods.)
Draw the Influence Line Diagram for involving a moving unit load 1 unit. VD = f (x)AV = f (x)RB = f (x)
Replace the loading (Figure 1) by an equivalent resultant force and couple moment at point O. Suppose that F1={8i−2k}kN and F2={−4i+5j−2k}kN. Part A Part complete Determine the resultant force. Enter the x, y, and z components of the force in kilonewtons to three significant figures separated by commas. Part B Determine the equivalent resultant couple moment about point O. Enter the x, y, and z components of the moment in kilonewton-meters to three significant figures separated by commas.
The 100-mm-diameter pulley shown fits loosely on a 10-mm-diameter shaft for which the coefficient of static friction is Determine the minimum tension T in the belt needed to (a) raise the 100-kg block and (b) lower the block. Assume that no slipping occurs between the belt and pulley and neglect the weight of the pulley Choices: A. TMAX = 1075 N, TMIN = 906 N B. TMAX = 1075 N, TMIN = 690 N
solve for the total head loss given that the pressure drop between the junction=250kPa. (f=0.02) Use 3 decimal places
Determine support reaction. Given a=5 m b=10 m P=30 KN
The moment diagram (answer in kips) P=8.3 kips, b = 23 ft, h=13 ft