Consider the given figure. Given: P = 5 kN and Q = 10 kN.A Pratt roof truss is loaded as shown. Determine the force in members FH, Fl, and Gl.Note: please double check your answers!. Thanks Consider the given figure. Given: P = 5 kN and Q = 10 kN.ABDFHJ6.75 mCEGIK00003 m3 m3 m3 m3 m3 mL A Pratt roof truss is loaded as shown. Determine the force in members FH, FI, and Gl.The force in members FH isThe force in members FlisThe force in members GlisKN (CompressionKN (Click to select)KN(Click to select) ✰

Answered: Image /qna-images/answer/101cf78e-d6af-4a10-9fcd-c2204704be91.jpg

Answered: Consider the given figure. Given: P = 5…

Consider the given figure. Given: P = 5 kN and Q = 10 kN. A Pratt roof truss is loaded as shown. Determine the force in members FH, Fl, and Gl. Note: please double check your answers!

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Discuss the principles of open channel flow control and regulation?

A: The management of flow behavior and water levels to achieve specific objectives in natural and…

Q: In gradually varied flow, the channel bottom, water surface, and EGL are parallel. Select one: O…

A: Given Channel bottomWater surfaceEGLTo find out TRue or false

Q: 1. Draw the free-body diagram of the beam. Welded pin G. A -1200 mm 600 - 300 mm mm

Q: A rock is dropped from a sea cliff and the sound of it striking the ocean is heard 3.9 s later Part…

A: Given data:Speed of sound (v) = 340 m/sTotal time (t) = 3.9 seconds (time to hear the sound)Height…

Q: For the concrete retaining wall and footing shown: Calculate the algebraic summation of the moments…

A: A concrete retaining wall is givenTo determine the algebraic sum of the moment of various forces…

Q: Discuss the challenges associated with unsteady flow analysis in open channels ?

A: Because flow behavior in open channels is complex and dynamic, unsteady flow analysis poses a number…

Q: A W24x104 is used as a bending member in support of two factored point loads, as shown marks. Is the…

A: A W24x104 is used as a bending member in support of two factored point loads, as shown below. The…

Q: How did English Queen Anne furniture differ from colonial American examples?

A: “Since you have posted multiple questions, we will provide the solution only to the first question…

Q: What is the value to use for 'b' in inches for the 22ft long T-Beams with center to center spacing…

A: Answer Explanation:

Q: Explain the concept of fracture toughness and its importance in material design?

A: Fracture toughness refers to the fundamental ability of materials to resist fracture under applied…

Q: To solve the question use table and equation on the photo. (Answers: 2.035*10^6 m^3 , 2.169*10^6…

A: At first we have to calculate delta of the different crops. Then we will calculated the consumptive…

Q: Explain the factors contributing to soil liquefaction?

A: Soil liquefaction, the temporary loss of strength and stiffness by saturated soil due to increased…

Q: Find the centroid of the following cross-sections and planes.

A: X = 7.4194Y = 5.1452Explanation:Step 1:Step 2:Step 3:

Q: 1. Check the compactness of W36x529, W21x48 and W14x99. 2. Verify the available flexural strength of…

A: The first part of the question is asking to check the compactness of the given steel sections.…

Q: Help me and show me the steps to Classify the soil by the AASHTO system.

A: The objective of the question is to classify the given soil sample using the AASHTO (American…

Q: By using the yield line theory, find the value of uniformly load (w) of the Isotropic slab, take…

Q: Discuss the concept of elasticity and plasticity in materials?

A: The ability of a material to respond to external loads through elasticity and plasticity is one of…

Q: pump is to deliver water from an underground tank against a static head of 40m. The suction pipe 50m…

Q: Water flows steadily from the large open tank shown in the figure. If viscous effects are…

A: Determine the manometer reading (h).

Q: QUESTION 2 a) Draw the precedence diagram for the activities depicted in the Table below. b) Analyse…

Q: Explain why the strength of hot mix asphalt is not necessarily the most important property of the…

A: The strength of hot mix asphalt (HMA) is certainly an important property, but it's not necessarily…

Q: 1. Consider a water jet having a diameter of D = 1 cm and a flow of Q = 1 L/s. The jet is deflected…

Q: absorption is 0.21%

A: Yes, it is correctAbsorption of aggregate using the formula Absorption =…

Q: Determine the central axis of the system with sliding vectors defined as follow: A = 2i + j + 3k;…

A: The central axis of the system is 11i+j+2k which do not satisfy the given direction copine…

Q: P5.3. Write the equations for shear and moment between points A and B. Select the origin at B. Plot…

Q: What is the peak flow from a watershed with 5 acres and runoff coefficient of 0.7, for a 10-year…

A: Peak flow = 0.529 cubic ft/secExplanation:

Q: tion 3. An oaded mim square tied column 1s 8-25 mm diameter bars equally distributed on its sides.…

A: To determine the maximum nominal axial strength of the column, we need to consider the contribution…

Q: Line AP The following observations were taken from stations P and Q. Length (m) Bearings N 60° 30' E…

Q: Example 1.1 Calculate the velocity gradient and the shear stress for y=0., 0.1, and 0.5m if the…

A: (i) Velocity gradient dydu=50(2−2y)(ii) Shear stress at y=0m τ=0.1Paat y=0.1m τ=0.09Paat y=0.5m…

Q: Since your team is doing such an outstanding job for your client, they requested a preliminary…

A: Peak fluro = 3600 cfx at t = 3hoxExplanation:

Q: Why is the concept of Geologic Time of importance to civil engineering and give an example where it…

A: The idea of Geologic Time holds significant importance in the field of civil engineering due to a…

Q: Why are overlays so dangerous?

A: Overlays can present risks and dangers in a number of contexts, including software development,…

Q: Solution por A and B?

A: (A) as per English unitsMaximum bending stress in beam is = 20.75 ksi (B) as pe metric unitsMaximum…

Q: The rod OA rotates clockwise with a constant angular velocity of 6 rad/s. Two pin-connected slider…

Q: How much work does an elevator motor do raising a mass of 1176 kg vertically 15.3 m?

A: The objective of the question is to calculate the amount of work done by an elevator motor to lift a…

Q: Hand Writing not allowed please provide Typed answer

A: The distance between v1 and v2 is √37 or approximately 6.08 units.Explanation:Formula for distance…

Q: Determine the force in each member of the truss and state if the members are in tension or…

A: MemberForceNatureAB1.768 kNCompressionBC1.546 kNCompressionBE0.250 kNCompressionBF0.344…

Q: A soil profile consists of 10-m-thick fine sand of effective size 0.15 mm above a very thick layer…

Q: Two Steel Rods (ASTM A36) and One Aluminum Rod (1060 0) are assembled to two rigid cover plates. The…

Q: NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to…

Q: Part A The magnitude of the force exerted on the wrench is 20 lb (Figure 1). What moment does the…

A: The magnitude of force is 20 lb

Q: An unconfined aquifer has experienced an average water level drop of 11-ft over the past year. If…

Q: PROBLEM 1. Solve for the EIO and Ely at the midpoint of segment CD if a distr- ibuted uniform load…

Q: لا يحتاج حاسب وزن الفنية Design of one way slab: The cross section of a continuous one-way slab in a…

Q: Explain the concept of yield strength and its importance in material testing.

A: Yielding is a vital mechanical characteristic of substances which explains the highest load…

Q: 1. A short rectangular reinforced concrete column 500 mm wide by 700 mm deep contains 8-28 mm…

A: Note : Since you have posted a question with multiple sub-parts, we will solve the first three…

Q: The beam has a width of 400 mm and a total depth of 500mm. It is subjected to 200 KN.m. ultimate…

Q: Sections 12.1-12.2 For Problems 12.1 through 12.17 use the force method (method of con- sistent…

A: Given information:the member BD is a is redundant member. Bar areas isAD= 4, BD=5, CD=4 in2.

Q: Project: Impact of Weather on temperature in dallas texas CE 3301 Proect

A: The objective of this project is to analyze the impact of weather on the temperature in Dallas,…

Q: A rectangular column footing is to be designed to carry the following column loads: PDL = 850 kN MDL…

A: Column size 500* 500mPDL = 850 kNPLL = 690 kNMDL = 160 kN-mMLL = 190 kN-mL= 1.4Bf'c = 27.6 MPafy =…

Concept explainers

Members with compression and bending

Compression members are structural elements that carry compressive axial force. They are the vertical members of a building that support beams and their design, which is governed by buckling and strength. Columns are known as struct or compression members, which are subjected to compressive forces. These members provide stiffness to the building and avoid any imperfection regarding the transfer of axial load. For instance, webs in a truss, braces in a framed structure, tiers, and so on.

Question

100%

Consider the given figure. Given: P = 5 kN and Q = 10 kN. A Pratt roof truss is loaded as shown. Determine the force in members FH, Fl, and Gl. Note: please double check your answers!. Thanks

Consider the given figure. Given: P = 5 kN and Q = 10 kN.
A
B
D
F
H
J
6.75 m
C
E
G
I
K
0000
3 m
3 m
3 m
3 m
3 m
3 m
L

A Pratt roof truss is loaded as shown. Determine the force in members FH, FI, and Gl.
The force in members FH is
The force in members Flis
The force in members Glis
KN (Compression
KN (Click to select)
KN
(Click to select) ✰

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Introduce the problem statement

VIEW

Step 2: Determine support reactions

VIEW

Step 3: Geometry of truss

VIEW

Step 4: Compute member force using method of section

VIEW

Solution

VIEW

Step by step

Solved in 5 steps with 8 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

1. Using DIM, solve for: P = 108kN a. Ymax (mm) b. A (rad) Use E = 200 GPa. 90 kN/m 165 KN 120 kN.m LA A 1m 2m 1m 2m 1m/ 2m B CD E F Dimensions are in mm 200 80 400 300 50 50
Analyse the frame shown in figure below by slope deflection method and draw BMD and SFD. X kN/m X= 34.4KN/m 1.25 EI В 3 m 2 EI 2 EI A 4 m
3 Homework.pdf 1 من 1 EAAMPLE (1). A circular bar having 200 mm² area is subjected to axial loads as shown in Fig Find the value of ( P) and the total elongation . Take E=2*105N/mm2. A B 50kN 50kN -lokN 1M 1M 1M
EXAMPLE (1) A circular bar having 200 mm² area is subjected to axial loads as shown in Fig „Find the value of ( P) and the total elongation . Take E=2*10ʻ N/mm?. A в C D 50kN 50kN -lo KN 1M 1M 1M ナ

Determine the elastic section modulus, plastic modulus and the shape factor about the horizontal axis for the steel beam shown. Consider two channels С8х18.75 A, = 3,555 mm? bf = 64.2 mm tf = 9.9 mm tw = 12.4 mm d = 203.2 mm X = 14.35 mm Ix = 18.31 x106 mm ly = 0.82 x106 mm* 2-C8x18.75 %3! %3D
Q2: 1.2 D.L x l.6 L.L Mu A: Find the maximum value of (p) that can be applied to the beam shown. Use f. =21.7 MPa and fy = 350 MPa (WD.L is included the self-weight of beam). %3D b hy P Wu =7 kN/m D.L 2028 A 500 mm 4028 250 mm -7.5 m-
Q3 Analyse the frame shown in figure below by slope deflection method and draw BMD and SFD. MSKN/m 1.5E1 1.5EI 3.5m 5 m 大不

Problem 1 The continuous beam shown in the figure is fixed at both ends A and D, and supported by rollers at B and C. Assumel = 800 x 10° mm“ and E = 70,000 MPa. F W1 A В 8 m 8 m 4 m 4 m Set w1 (kN/m) F(kN) s (mm) A (1,2,3,4,5) B (6,7,8,9,0) 20 60 25 25 50 15 If there is a settlement of S at the support C, solve the following using slope deflection method: 6. Moment at D, Mp in kN-m. (10 pts)
EXAMPLE (1) A circular bar having 200 mm? area is subjected to axial loads as shown in Fig „Find the value of (P) and the total elongation. Take E=2*10 N/mm?. A В C D 50KN 50kN -lo KN 1M 1M 1M ナ
The continuous beam shown in the figure is fixed at both ends A and D, and supported by rollers at B and C. Assume I = 800 x 106 mm and E = 70,000 MPa. F W1 BO C D 8 m 8 m 4 m 4 m w1 (kN/m) | F (kN) S (mm) Set A (1,2,3,4,5) B (6,7,8,9,0) 20 60 25 25 50 15 If there is a settlement of S at the support C, solve the following using slope deflection method: 3. Reaction at A, RA in kN. (10 pts)
Q1/ For a simple beam loaded as shown in Figure 1. Determine the slope and deflection at the position midway between the supports. Take E for beam material 2x10³N/mm², I= 5x108 mmª. 25 kN C D E 3 kN/m F 82 kN-m BANDENYJUNIC B 2 m2 m2 m2 m2 m2 m Figure 1
Suppose that d = 0.14 m in (Figure 1). Part A Determine the angle at which the 500-N force must act at A so that the moment of this force about point B is equal to zero. Express your answer in degrees to three significant figures. 0= Submit VE ΑΣΦ | 41 Request Answer Figure vec 1 m B ISWE ? 2 m-