Consider the measuring instrument of the Pressure Type Thermometer shown in the Figure 1. Then answer the following questions: 1-Sketch the specific schematic diagram of functional elements for this measuring instrument. 2- Is the measuring instrument of the Pressure Type Thermometer considered as Null or Deflection type measuring device, why? 3-What is the opposing effect in this measuring instrument which is introduced according to the physical effect and where does it occur? 4-Sketch only the specified configuration of input-output relationship diagram including only two Figure 1. quantities of Interfering inputs with only two quantities of Modifying inputs:

Consider the measuring instrument of the Pressure Type Thermometer shown in the Figure 1. Then answer the following questions: 1-Sketch the specific schematic diagram of functional elements for this measuring instrument. 2- Is the measuring instrument of the Pressure Type Thermometer considered as Null or Deflection type measuring device, why? 3-What is the opposing effect in this measuring instrument which is introduced according to the physical effect and where does it occur? 4-Sketch only the specified configuration of input-output relationship diagram including only two Figure 1. quantities of Interfering inputs with only two quantities of Modifying inputs:

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter6: Forced Convection Over Exterior Surfaces

Section: Chapter Questions

Problem 6.35P

See similar textbooks

Similar questions

Please explain me how you got the answer. Consider a pulley system shown below. Let x be the displacement of the pulley's center of mass. Assume there is no slip between the cord and the pulley. What is the potential energy of the system? Select all that apply.
(Q4) A thermopile 18 constructed with Iron-constantan materials. Four junctions are maintained at 300°C and for junctions are maintained at 40°C. The output of the thermopile is connected to a potentiometer. What voltage will be indicated if both terminals of the potentiometer are at the same temperature? What is the temperature indicated in this case?
The torsion balance shown in the figure below is used in an experiment to measure radiation pressure. The suspension fiber exerts an elastic restoring torque. Its torque constant is 1 ✕ 10-11 N·m/degree, and the length of the horizontal rod is 5.10 cm. The beam from a 1.90 mW helium-neon laser is incident on the black disk, and the mirror disk is completely shielded. Calculate the angle between the equilibrium positions of the horizontal bar when the beam is switched from "off" to "on."
Use appropriate diagram and sketches. When the cold junction of a thermocouple thermometer is at 0° C and the hot junction at 100°C the millivoltmeter shows a deflection of 4.2 mV towards the left. The cold junction is now put in an unknown temperature while maintaining the hot junction at 100°C. The millivoltmeter now shows a deflection of 5.2 mV towards the right. Calculate the unknown temperature
Q:. For a transistor as shown in figure. |, find maximum allowable power dissipation. Note: - give all assumptions in your solutions
Suppose the frequency of a system is measured to be 2rad/s and after the addition of another mass the frequency is measured to be 1rad/s, calculate the mass and stiffness.
DC and AC subject: 1. Consider a wire carrying a current in the presence of a magnetic field, and a given flux density of 0.25 T. If the wire is 1.0 m long and carries a 0.5 A current, what is the magnitude of the force induced in the wire? 2. The wire shown is moving in the presence of a magnetic field. With the information given in the figure, determine the magnitude and direction of the induced voltage in the wire. (see the figure below)
A Large wind turbine has blade span diameters of 110 m. It sits high off the ground where the average wind speed is 7 m/s. Assume the air density to be 1.25 kg/m3, and the efficiency of the wind turbine, its generator and its electric grid synchronization device is 26%. What is the average electric power that this turbine can output to the grid? a. Sketch the problem. b.Draw lines identifying the control volume, or control mass. c.Identify the states with numbers, letters, or descriptions such as “in” and “out”. d.Write down the knowns and unknowns. e.Identify what is being asked for. f.State all assumptions.
4 ) Every temperature measuring instrument makes use of specific physical property in order to measure temperature objectively . Which physical properties are used in thermocouple , PT sensors and mercury - in - glass thermometer ? Briefly describe each of this methods.
Looking for correct handwritten solution. 1)An industrial water shutoff valve is designed to operate with 10 N of effort force on the wheel. The valve will encounter 30 N of resistance force applied to an axle that is 0.35 m in diameter. What is the required diameter of the wheel?
Define the displacement compatibility equation, the virtual loading state and the main system of the structure.
Under what conditions does the Monoclinic system reduce to the orthorhombic system? Do not use any bot to answer the Question.