Consider the system shown in (Figure 1). Figure 30 m 3 m < 1 of 1 Part A If the pipe has a mass per unit length of 1100 kg/m, determine the minimum tension developed in the cable Express your answer using three significant figures and include the appropriate units. Tmin= 809 4 KN Submit Previous Answers Request Answer Provide Feedback X Incorrect; Try Again; 5 attempts remaining ?

Consider the system shown in (Figure 1). Figure 30 m 3 m < 1 of 1 Part A If the pipe has a mass per unit length of 1100 kg/m, determine the minimum tension developed in the cable Express your answer using three significant figures and include the appropriate units. Tmin= 809 4 KN Submit Previous Answers Request Answer Provide Feedback X Incorrect; Try Again; 5 attempts remaining ?

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.2.9P: A safety valve on the top of a tank containing steam under pressure p has a discharge hole of...

See similar textbooks

Similar questions

Calculate the maximum force P that can be applied in a phosphor bronze spring having mean diameter of 150 mm and consisting of 24 turns of 10-mm diameter wire when the spring is stretched 180mm. Use G = 42 GPa. Group of answer choices 233.11 N 113.33 N 116.667 N 225.56 N
A semi-elliptic spring used for automobile suspension, consists of twoextra full-length leaves and eight graduated-length leaves, including themaster leaf. The centre-to-centre distance between the two eyes is 1 m.The leaves are made of steel 55Si2Mo90 (S = 1500 N/mm yt2 andE = 207 000 N/mm2) and the factor of safety is 2. The maximum springload is 30 kN. The leaves are pre-stressed so as to equalize stresses in allleaves under maximum load. Determine the dimensions of thecross-section of the leaves and the deflection at the end of the spring.
Calculate the maximum force P that can be applied in a phosphor bronze spring having mean diameter of 150 mm and consisting of 24 turns of 10-mm diameter wire when the spring is stretched 180mm. Use G = 42 GPa.
Determine the possible range for R is the equivalent spring stiffness constant varies from 50 N/m to 500 N/m
An open coiled helical spring is subjected to an axial loadof 50 kN. Determine the deflection of the spring andmaximum shear stress in the spring wire. The springparticular are as follows:(i) No. of coils = 4(ii) Mean radius of coil 30 mm(iii) Diameter of the spring wire = 5 mm(iv) Modulus of rigidity = 80000 MPa(v) Angle of helix = 10"(vi) Young's modulus, E = 2 x 105 N/mm²
A typical compound helical spring consists of two coaxial closed coil spring having the following particulars: Outer spring 1: Mean coil diameter = 100mm Wire diameter = 12.5 mm No. of turns = 15 Inner spring 2: Mean coil diameter = 75 mm No. of turns = 20 Both the springs are of equal initial length when unloaded. If the working stress for each spring is to be the same. The modulus of rigidity for the wire material is 80 GPa. Calculate the following: a. Diameter of steel wire for inner spring b. Stiffness of inner spring c. Stiffness of the compound spring
(13) A spring has an overall length of 44.0in & sustains a load of 15,000lb @ its center. The spring has three full-length leaves & 15 graduated leaves with a central band 4.0in wide. All leaves are to be stressed to 60,000psi when fully loaded. The ratio of total spring depth to width is to be approximately 2.0. Determine: (a) the width & thick ness of the leaves; (b) the initial space that must be provided between the full length & the graduated leaves before the band is applied; (c) What load is exerted on the band after the spring is assembled?
A closely coiled helical spring is to carry a load of 500N. Its mean coil diameter is to be 10 times that of the wire diameter. Calculate these diameters if the maximum shear stress in the material of the string is to be 8OMN/mA2.
Physics for Engineering A uniform bar 3.00 m long is held by ropes at the ends making angle 60.0 and 30.0, respectively, with the horizontal. A weight of 200 N is hung 0.500 m from the left end where the 60.0 rope is attached. Find the tension in the ropes (T1 & T2) and the weight (W) of the bar. (Hint: Formulate three equations for the three unknowns, 2 equations for the 1st condition and 1 equation for the 2nd condition.)
A hand cranking lever, as shown in Figure 6 below, is used to start a truck engine byapplying a force F = 400 N. The material of the cranking lever has a yield strength = 320 MPa;Ultimate tensile strength = 500 MPa; Young’s modulus = 205 GPa; Modulus of rigidity = 84 GPaand poisson’s ratio = 0.3. Assuming factor of safety to be 4 based on yield strength, design thediameter of the lever at section X-X near the guide bush using: a) Maximum distortion energytheory; and b) Maximum shear stress theory.
Question 4A close-coiled helical spring is to have a stiffness of 90 kN/m and is to exert a maximum force of 3.7 kN. If the mean diameter of the coils is 80 mm, and the maximum stress is not to exceed 300 MPa, calculate the required number of coils and the diameter of the steel rod from which the spring should be made (G=80 GPa).
A hard-drawn steel wire extension spring has a wire diameter of 4mm, an outside coil diameter of 28 mm, and initial tension of 1200 N is applied to the spring. The spring shows an extension of 85 mm. The approximate number of turns is 25. From the given information: Determine the physical parameters of the spring such as mean diameter, spring index, maximum shear stress, total number of turns, Wahl’s stress factor, free length of the spring, and pitch of the coil