Consider the truss shown in (Figure 1). TakeA = 0.0015 m? and E = 200 GPa Suppose thatF = 21 kN.Part ADetermine the vertical displacement at joint (2 measured upward.Express your answer to three significant figures and include the appropriate units. Enter positive value if thedisplacement is upward and negative value if the displacement is downward.µAD6 = 1.4Figure1 of 1SubmitPrevious Answers Request Answer2 m2 m4 104X Incorrect; Try Again; 8 attempts remaining632 mPart B18(3)Determine the force in the member 5 of the truss and state if the member is in tension or compression.Express your answer to three significant figures and include the appropriate units. Enter negative value in the caseof compression and positive value in the case of tension.F

Consider the following diagram : At joint 3: ∑ Fy = 0F = F3 SinθF = F3 Sin(45)F3= FSin(45)F3=…

Consider the truss shown in (Eigure 1). Take A = 0,0015 m² and E = 200 GPa Suppose that F = 21 kN. Part A Determine the vertical displacement at joint (2) measured upward. Express your answer to three significant figures and include the appropriate units. Enter positive value if the displacement is upward and negative value if the displacement is downward. HẢ De = 1.4 m Figure < 1 of 1 Submit Previous Answers Request Answer 2 m 2 m +10 X Incorrect; Try Again; 8 attempts remaining 6 2 m Part B Determine the force in the member 5 of the truss and state if the member is in tension or compression. Express your answer to three significant figures and include the appropriate units. Enter negative value in the c of compression and positive value in the case of tension.

Consider the truss shown in (Eigure 1). Take A = 0,0015 m² and E = 200 GPa Suppose that F = 21 kN. Part A Determine the vertical displacement at joint (2) measured upward. Express your answer to three significant figures and include the appropriate units. Enter positive value if the displacement is upward and negative value if the displacement is downward. HẢ De = 1.4 m Figure < 1 of 1 Submit Previous Answers Request Answer 2 m 2 m +10 X Incorrect; Try Again; 8 attempts remaining 6 2 m Part B Determine the force in the member 5 of the truss and state if the member is in tension or compression. Express your answer to three significant figures and include the appropriate units. Enter negative value in the c of compression and positive value in the case of tension.

Principles of Foundation Engineering (MindTap Course List)

8th Edition

ISBN:9781305081550

Author:Braja M. Das

Publisher:Braja M. Das

Chapter6: Vertical Stress Increase In Soil

Section: Chapter Questions

Problem 6.4P: Refer to Figure P6.4. A strip load of q = 900 lb/ft2 is applied over a width B = 36 ft. Determine...

See similar textbooks

Similar questions

USING DOUBLE INTEGRATION METHOD Consider 250 mm x 250 mm (bxh) mm section and e = 100000 MPa DETERMINE VERTICAL REACTION AT B DETERMINE SLOPE REACTION AT B DETERMINE DEFLECTION AT D Values: A = 9.4 M B = 5.5 M C = 10.6 KN/M D = 33 KN
A downward load of Q = 33 kN is applied to rigid bar ABD as shown in the sketch. Axial member CDE is subjected to a downward load of P = 27 kN at joint E plus a force at joint D from the rigid bar. The axial member has an elastic modulus of E = 69 GPa and a cross-sectional area of A1 = A2 = 145 mm2. Assume that a = 390 mm, b = 220 mm, c = 630 mm, and d = 490 mm. Determine the vertical displacement of joint E. Draw a free body diagram of rigid bar ABD, and determine the magnitude of the vertical reaction force at pin D.Answer:D = kN
Determine the vertical displacement at Joint A, B, C, D, E
2. (CASTIGLIANO'S THEOREM) Determine the vertical displacement of point B of the beam shown below. E= 200 GPaI= 150(10) mmsP= 15.4 kNQ= 6.4 kN/ma = 6 m
solve for deformation in figure B. given V= 10-0 and area = 2.0in^2
For the beam and loading shown below, determine the beam deflection at point H. Assume that EI = 6.9 × 104 kN·m2 is constant for the beam; w = 6.4 kN/m, LHA = 3.0 m, LAB = 6.0 m.
determine the vertical reaction at B in kN using any Geometric Method. Consider 250 mm x 400 (b x h) mm section and E = 100,000 MPa. Enter the absolute value only and round-off your answer to 3 decimal places
Using ANY GEOMETRIC METHOD Consider 250 mm x 400 (b x h) mm section and E = 100,000 MPa. Enter the absolute value only and round-off your answer to 3 decimal places. GIVEN: a = 5.6 m b = 4.4 m c = 15.9 kn/m d = 22 kn QUESTIONS: 1. Determine the VERTICAL REACTION at B in KN. 2. Determine the SLOPE at B in DEGREES. 3. Determine the DEFLECTION at D in MM. 4. Determine the DEFLECTION AT MIDSPAN OF THE BEAM in MM. Thank you! Please answer all. ❤️
In the rectangular figure shown, specific gravity of concrete is 2.4 and the coefficient of friction between the dam and foundation is 0.4. Use 1.5 as the FOS against sliding. a. Find the value of overturning moment. b. determine the b of the concrete dam needed to prevent the dam from sliding. c. Is the dam also safe from overturning?
The continuous beam shown in the figure is fixed at both ends A and D, and supported by rollers at B and CAssume I = 800 x 106 mm4 and E = 70,000 MPa. W1 (kN/m) = 25 F (kN) = 50 S (mm) = 15If there is a settlement of S at the support C, solve the following using slope deflection method:
For the beam and loading shown below, determine the beam deflection at point H. Assume that EI = 5.6 × 104 kN·m2 is constant for the beam; P = 40 kN, LAB = 3.9 m, LBH = 3.9 m.
For the beam and loading shown below, determine the beam deflection at point H. Assume that EI = 6.4 × 104 kN·m2 is constant for the beam; w = 3.6 kN/m, LAB = 3.7 m, LBC = 7.4 m, LCH = 3.7 m.