create 2 fourbar designs that include the dimensions and angle of motion

Q: ! Required information A uniform steel rod of cross-sectional area A is attached to rigid supports…

A:

Q: The elements of the mechanism for deployment of a spacecraft magnetometer boom are shown. Determine…

A:

Q: The 40-mm-diameter A992 steel shaft is subjected to the torques shown where T=600 N⋅m. Determine…

A: Given:Diameter, d = 40 mm = 0.04 mShear modulus of A992 steel shaft, G = 75 GPa = 75109 PaT = 600…

Q: A steady-flow Carnot cycle uses water as the working fluid. Water changes from saturated liquid to…

A: The Carnot cycle is an ideal cycle that produces the maximum efficiency as compared to other cycles…

Q: The incredibly rare Ideal Gas HRUDIUM has a spcific heat that is a function of temperature given by…

A: Given thatThe specific heat of ideal gas HRUDIUM is given byTo findThe change in the specific…

Q: Two couples act on the frame. If the resultant couple moment is to be zero, determine the distance d…

A:

Q: The overhang beam is subjected to the uniform distributed load having an intensity of w=60 kN/m.…

A:

Q: The figure below shows a spray dryer operating at a steady state. The mixture of liquid water and…

A:

Q: 2-1. Determine the magnitude resultant the magnitude of the force FR F₁+F2 and its orientation 0,…

A:

Q: The couple M=129 kip-in. acts in a vertical plane and is applied to a beam oriented as shown.…

A:

Q: Air at 10 °C enter an 18 m de long rectangular duct of cross section 0.15 m X 0.20 m at a velocity…

A:

Q: A tensile test is being conducted on a steel-rod specimen with a gauge length of L0=4.0 in and an…

A: given :Intial length Lo = 4 inInitial diameter do = 0.75 inFinal length Lf = 5.53 in

Q: 78 7+ 2L AL 2L | 21 TL

A:

Q: In the casting of steel in the sand mold conditions, the mold constant in Chvorinov's rule is given…

A:

Q: You need to produce a Ci-Ni alloy having minimum yield strength of 20,000psi, a minimum tensile…

A: Required properties for Cu-Ni alloy:Minimum yield strength (σy) = 20,000 psiMinimum tensile strength…

Q: 3. 0.1 kg of Water is compressed in a piston cylinder assembly adiabatically. The water starts out…

A:

Q: o = nioij nj [50 10 30] 0.693) 10 95 20 30 20 15 5 = 87.47 MPa

A: The matrix operation is as follows-Here, A, B, and C are sequential matrices respectively.

Q: 5. 250 mL of cold water (2° C) from the refrigerator is in a glass and placed on the counter in the…

A: Specific Heat of Water

Q: CONVERT TO NM 2 Irad 52 TO kg.M 2

A:

Q: Calculate μ, Cv, K, and Pr for oxygen at 100, 300, and 1000 K, and 1 atm. Compare your calculated…

A:

Q: 1 in. -10 in.- t2 in.- a t1 in. 10 in. P kips Р x ft- 3 ft In In tl in. Determine the maximum stress…

A:

Q: Water enters the constant 120-mm inside-diameter tubes of a boiler at 7 MPa and 65°C and leaves the…

A:

Q: 2 When a bay is acted by a suddenly applied focal then, in this case, P& respeting force equals to…

A: Applied load = P = 50 kNNegelcting the self weight of the bar.Find:Resulting force when the load is…

Q: For the cross sectional area shown in the Figure: below: a) Locate the centroid in both the X and Y…

A:

Q: Calculate the rotation matrix, R, if frames {A} and {B} are originally coincident then a) Frame {B}…

A: It is asked to find the final frame after rotation

Q: A gas refrigeration system utilizing air as the working fluid possesses pressure ratio of 3. The air…

A: Pressure ratio, PR = 3Inlet temperature to the compressor, T1 = 5°C = 278KOutlet temperature from…

Q: A shaft, lever, and handle, welded together, with a combined point G, supported by a thin link, CD,…

A: 1 structures.To find:(a) Draw free-body diagram of each.

Q: 1. 37 kg of the ideal gas Air at 650°C, 2 MPa fills a piston/cylinder assembly. (state 1) The air is…

A:

Q: etely. Successive blurred Digit show

A:

Q: How are you solving the equations in step 4 to get the values for Tad, ab, ac? Especially when each…

A: We have following equations

Q: The principal stresses at a point P in a solid are 70 MPa, -70 MPa and 0. The yield stress of the…

A: In solid mechanics, when a material is subjected to external forces, it experiences internal…

Q: Determine the force in member GK of the loaded symmetrical truss. Enter a positive number if in…

A: Therefore, the distance from point J to the arc length Centre point 'S' is 0.04236 ft

Q: Engineering Mechanics (Like/Thumbs-up will be given. Write the solutions&FBD legibly. Include…

A: The free-body diagram of the support reactions are given below.

Q: Q1: Fundamentals Problem: a) A Deep-sea diver reached 5 m below the free surface of a river.…

A: Since you have posted multiple questions, we will provide the solution only to the first question as…

Q: A 15-meter long beam-tank assembly supports the loading shown in addition to its weight, which is a…

A: The outer diameter of cylinder is .The inner diameter of cylinder is .

Q: Determine the moment of the force about point O. Let r = 2 m, F = 413 N, and = 26.7 Note: Calculate…

A: Given data :Radius Angle Force To calculate :Moment of the force about Point

Q: Consider a 210-MW steam power plant that operates on a simple ideal Rankine cycle. Steam enters the…

A: Given:To find:The mass flow rate of the steam.

Q: The 30-kg gear is subjected to a force of P=(20t)N where t is in seconds. Determine the angular…

A: mass of the gear m=30 Kgforce applied P=20tgear radius of gyration is Ko=125 mmto findthe angular…

Q: The drive shaft of the motor is made of a material having an allowable shear stress of τallow= 72…

A:

Q: 1) Air, treated as an ideal gas, goes through a polytropic process from 125 kPa, 325 K to 300 kPa…

A: According to the given dataP1=125KPa and P2=300KPaT1=325K and T2=500K1-2 is a polytropic process We…

Q: You are in charge of replacing a chiller that is used as part of a distillation process that…

A:

Q: If a surface has heights and depths as illustrated below, evaluate Ra, Rp, Rv, Rt, and Rz values (in…

A: The average roughness,

Q: 5. Determine the Miller indices for the following structural elements (SHOW YOUR WORK). Do PLANES A…

A: To determine:Miller indices of Plane A and Plane B.

Q: 1a. Consider the problem 2-15 from Ozisik (1993). Starting with the heat diffusion equation, Eq.…

A:

Q: 5.2. A rigid bar of mass per unit length m carries a point mass M at its right end. The bar is…

A: Given Data

Q: 1 208000 1 208000 (THoop – 0.29 X ĀLong ) = 266 X 10-6 - (-0.29 x + Long) = 69.6 × 10-6 НООР = X

A:

Q: Calculate the decrease of enthalpy of 2 kg of Butane from 2 MPa, 800 K and 100 kPa, 0.35 kg/m3, in…

A:

Q: 7. Determine the torsional shear stress in a circular shaft with a diameter of 52 mm when subjected…

A:

Q: For the log brace shown, select the set of 3 Free Body Diagrams that would be used to solve for the…

A: To determine:Free body diagrams

Q: The length is varied by a factor of 1.58 by what factor does the height vary to keep all other…

A: The maximum stress in a rectangular cross-section beam supported at both ends with a single load in…

Engineering Drawing

Technical drawing has been around since ancient times. As in the ancient Renaissance, complicated drawings were created, including Leonardo da Vinci's drawing. Modern engineering drawing, including its specific orthographic projection with scale conventions, began in Europe (France) during the early stages of Industrialization. L.T. C. Rolt also made some of Marc's drawings for its block-making machinery (in 1799) that also may have contributed significantly to British engineering technology. Since he learned the art of presenting three-dimensional(3D) items in a two-dimensional(2D) plane, as we now term mechanical drawing.