Answered: critical hydraulic gradient will be…

critical hydraulic gradient will be estimated as The porosity of a certain soil sample was founc in be 80% and its specific gravity was 2.7; the (a) 0.34 I) 1.0 (b) 0.92 (d) 1.5

Principles of Foundation Engineering (MindTap Course List)

8th Edition

ISBN:9781305081550

Author:Braja M. Das

Publisher:Braja M. Das

Chapter2: Geotechnical Properties Of Soil

Section: Chapter Questions

Problem 2.8P

See similar textbooks

Related questions

Q: A soil sample has a unit weight of 16.87 KN/m3 and a saturation of 50%. When its saturation is…

Q: A soil has a discharge velocity of 6 x 10 m/s and a void ratio of 0.5. What is its seepage velocity?

A: Given data : Void ratio (e)=0.5Velocity (V)=6×10-7 m/s

Q: The rate of upward seepage taking place through a granular soil contained in a tank is 976.5…

Q: The vertically upward flow of gound water (an artesian condition) occurs through a sand deposit…

A: Given: Void ratio, e = 0.60 Specific gravity of soil particles, G=2.65 Hydraulic gradient (for quick…

Q: A silty clay has a plastic limit of 25 and a plasticity index of 30. If the clay has a liquidity…

Q: A soil sample has an initial unit weight of 16.7 Kilo-Newton per cubic meter with a saturation of 18…

A: Given data in question Degree of saturation Unit weight To find out Void ratio Specific gravity

Q: 7.14 For a sandy soil, the following are given: • Maximum void ratio = 0.86 • Minimum void ratio =…

Q: soil sample 10 cm in diameter is placed in a tube 1.2 m long. A constant supply of water is allowed…

Q: An anisotropic soil deposit has coefficient of permeability in vertical and horizontal directions as…

Q: The vertically upward flow of groundwater (an artesian condition) occurs through a sand deposit…

A: Given: The void ratio e is 0.60. The specific gravity of soil G is 2.65. Calculation: For necessary…

Q: 2.11 A sand has the following: Do = 0.2 mm, D = 0.4 mm, and void ratio e = 0.6. a. Determine the…

Q: The ratio of seepage velocity and discharge velocity for a soil is 2.5. Determine : (i) Porosity…

Q: The critical hydraulic gradient for a soil sample is equal to 1.01. If the specific gravity of the…

Q: Question attached

A: To determine: Hydraulic conductivity of clay.

Q: The hydraulic gradient for quicksand condition is equal to 1.22 with a void ratio of 0.41. The moist…

A: Given:- Moist unit weight Υt=19.17 KN/m3Void ratio e=0.41Hydraulic gradient, iC=1.22 To find:- water…

Q: For a falling laboratory permeability test on a fine sand, the following data are given: Length of…

A: Given data: Length of specimen = 10 cm.Diameter of specimen = 9.5 cm.Diameter of standpipe = 1.5…

Q: A soil sample has water content of 10%and wet unit weight of 20KN/M3.If the specific gravity of…

A: Solution: Given data: water content=10%Unit weight=20 kN/m3specific gravity=2.7 (a) Dry unit weight…

Q: Example 3 A sample of saturated soil with o = 14 % and Gs = 2.7. Find void ratio, total unit weight,…

Q: Determine the void ratio of he soil if its specific gravity is 2.7 and the ratio of unit weight of…

A: Given: Specific gravity, G = 2.7 Ratio of saturated and dry unit weight = 1.24

Q: h=1.2 m H1=1 =0.8 Soil H2=2 m valve open In flow

Q: The void ratio of the soil is 1.2. Determine the bulk unit weights for degree of saturation 55% and…

A: The given question is related with geotechnical engineering . In this question we are provided with…

Q: A soil has discharge velocity of 5 x 10-7 m/s and a void ratio of 0.50. Its seepage velocity will be…

Q: The specific gravity and in-situ void ratio of a soil deposit are 2.71 and 0.85 respectively. The…

Q: Problem D The critical hydraulic gradient for a soil sample is equal to 1.18. If the specific…

Q: A 0.7m long soil specimen is subject to a steady-state flow, as shown in Figure Q4. The saturated…

A: Hello dear this is the solution of your problem The answer is found to be Effective stresses at…

Q: A clay sample of thickness 50 mm undergoes 50% consolidation in 15 minutes when drainage is allowed…

Q: The critical hydraulic gradient for a soil sample is equal to 1.02. The specific gravity of soil…

A: Appreciate if there is detailed work with explanation and finds you helpful for ease of…

Q: The hydraulic gradient of a soil of specific gravity 2.67 and void ratio 0.45 is 0.46, calculate the…

A: Given: Specific gravity, G = 2.67 Void ratio, e = 0.45 Hydraulic gradient, i = 0.46

Q: A silty clay has a plastic limit of 25 and a plasticity index of 30. If the clay has a liquidity…

A: To find water content, degree if saturation, and moist unit weight

Q: A layered soil is shown in following figure. a) Estimate the hydraulic conductivity for flow in the…

A: Given data of soil Assume K1 = 10-3 cm/sec K2 = 2 *10-4 cm/sec K3 = 10-5 cm/sec K4 = 2 *10-3…

Q: Water table is at at depth of 10m in a silty soil mass. The sieve analysis indicate the effective…

A: Given: The depth of the water table is 10 m. The diameter D10 is 0.05 mm. The void ratio is 0.51.…

Q: The following data are given for a specimen of soil: MT = 221 g, Ms = 128 g, Gs = 2.7, S= 75%.…

A: Given data: Total weight of the soil (MT) = 221 g Total weight of solids (MS) = 128 g Specific…

Q: A vertical sand column of length 100 cm and cross section area of 150 cm² is allowing the water to…

A: Calculate the (a) rate of flow, (b) the Darcy velocity and (c) the average velocity.

Q: The results of two consolidated drained triaxial tests are as follows: Test o,(kN/m²) Ao,(kN/m²) 66…

A: GIVEN FOR TEST 1 σ3=66 KN/M2∆σ1=134.77KN/M2 FOR TEST 2 σ3=91KN/M2∆σ1=169.1KN/M2

Q: For a soil having a void ratio of 0.75 and percentage saturation of 85%, determine the porosity.…

A: Given data in question Void ratio 0.75 Saturation percentage 85% To find out porosity We will…

Q: The hydraulic gradient for quicksand condition is equal to 1.27 with a void ratio of 0.46. The moist…

Q: For a normally consolidated laboratory clay specimen drained on both sides, the following are given:…

A: The hydraulic conductivity (K) is given by: K=CV×γw×mv Where, CV = Coefficient of consolidation γw…

Q: The hydraulic gradient of a soil of specific gravity 2.67 and void ratio 0.45 is 0.46, calculate the…

A: Given: Specific gravity, G = 2.67 Void ratio, e = 0.45 Hydraulic gradient, i = 0.46

Q: The hydraulic gradient for quicksand condition is equal to 1.27 with a void ratio of 0.40. The moist…

Q: For a sandy soil with Gs 2.68, calculate the critical hydraulic gradient that will cause boiling or…

A: Critical hydraulic gradient is the hydraulic gradient at which boiling of sands starts. Formula for…

Q: The porosity of a certain soil sample was found to be 80% and its specific gravity was 2.7; the…

Q: The specific gravity of the soil particles is 2.7 and the porosity of the sample is 0.6. The…

Q: The rate of upward seepage taking place through a granular soil contained in a tank is 976.5…

Q: 20.0 kN/m^3 at a water content of 8.0%. Use Gs=

Q: A soil has a discharge velocity of 6 × 10-7 m/s and a void ratio of 0.5. Its seepage velocity is (a)…

A: Given data : Void ratio (e)=0.5Discharge velocity =6×10-7 m/s

Q: For the flow net shown below, the soil is isotropic having a permeability of 0.002 cm/sec, an…

A: Given Data k=0.002cm/s =1.73m/day e=0.6Gs=2.65 No. of Equipotential Drops Nd=equipotential line +1…

Q: The porosity of a sample of saturated sand in the loose state was 50%. Find the critical hydraulic…

A: Given data : Porosity (n%)=50 Specific gravity of soil (GS)=2.6 To find : Critical hydraulic…

Q: The critical hydraulic gradient for a soil sample is equal to 1.02. If the specific gravity of the…

A: Given: The critical hydraulic gradient for a soil sample is 1.02. The specific gravity of the solid…

Q: The hydraulic gradient for quicksand condition is equal to 1.26 with a void ratio of 0.58. The moist…

Q: Q2: A laboratory consolidation test on a soil specimen (drained on both sides) determined the…

A: To find the hydraulic conductivity (k) -

Q: Q2: A laboratory consolidation test on a soil specimen (drained on both sides) determined the…

Q: For the permeability test arrangement shown in Figure Qu2b, the cross-section area of the soil is…

Q: c) Determine the hydraulic conductivity of the sand in the field condition if the hydraulic…

A: Void ratio is defined as the ratio of the volume of voids to the volume of solids. The void ratio…

Q: Q3: A soil has a porosity (n) of 0.40 and a specific gravity of solids (Gs) of 2.70. Determine the…

A: n=0.4 Gs=2.7 to find critical hydraulic gradient

Q: H2 H3

Concept explainers

Asphalt Binders and Mixtures

Asphalt binders are subsidiary products procured during the refining process of petroleum while manufacturing gasoline, diesel, and similar petroleum products. Asphalt binders are obtained from the residue that remains after the distillation of petroleum, this residue is further subjected to steam distillation and oxidation to remove the traces of gas oil present in the residue. Certain additives or modifiers are also added to asphalt binders to alter them to suit different applications.

Question

I need the answer as soon as possible

critical hydraulic gradient will be estimated as
The porosity of a certain soil sample was found
to be 80% and its specific gravity was 2.7; the
(a) 0.34
(c) 1.0
(b) 0.92
(d) 1.5

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A soil sample has a dry unit weight of 17.92 kN/M3 and a void ratio of 50% .Compute the hydraulic gradient of the quicksand condition .
The critical hydraulic gradient for a soil sample is equal to 1.02. If the specific gravity of the solid is 2.67 andthe water content is 14%, determine: a) The degree of saturation and b) Dry unit weight at zero air voids.
A loose, uncompacted sand fill, 6 feet deep has a relative density of 40%. Laboratory tests indicate e_min = 0.46 and e_max = 0.9. Sand specific gravity = 2.65. Find dry unit weight of the sand fill.
A soil sample 10 cm in diameter is placed in a tube 1.2 m long. A constant supply of water is allowed to flow into one end of the soil at A and the outflow at B is collected by a beaker. The average amount of water collected is 2 cm3 for every 10 seconds. Determine the hydraulic gradient Determine the seepage velocity if the void ratio is 0.60 in cm/s. Determine the coefficient of permeability cm/s.
A sand sample has a bulk density of 20kN/m³ and a degree of saturation of 70%. If the specific gravity of soil grains is 2,65, the value of critical hydraulic gradient for the soil will be(Assume Yw = 10 kN/m³)
How to solve this question? A soil has a dry density of 1.84 g/cm3 and void ratio of 0.45. Calculate the factor of safety against quick sand condition if the hydraulic gradient is given as 0.46.
The hydraulic conductivity of a soil sample is 0.01 cm/sec at void ratio of 0.8. What will be the hydraulic conductivity of the same sample at void ratio of 1.
The vertically upward flow of groundwater (an artesian condition) occurs through a sand deposit where the void ratio is 0.60 and the specific gravity of soil particles is 2.65. What hydraulic gradient is necessary for a quicksand condition to develop?
Problem # 1. A constant head permeability test is performed on a sample of granular soil. The length of the soil sample is 15 cm and the cross-sectional area is 10 cm^2. If a 24 cm^3 volume of water passes through the oil sample in a 3-minute period and the constant head is 30 cm determine the followinga. Determine the coefficient of permeability of the soil.b. Find the discharge velocity.c. Compute the seepage velocity if the void ratio is 0.64.
Value of hydraulic conductivity of a sand is 0.010 cm/sec at a porosity of 0.45. Determine the hydraulic conductivity of sand at a porosity of 0.50?
A soil specimen having a volume of 0.012 m3 has a specific gravity of 2.60. It has a moist mass of 20.6 kg and a dried mass of 16.1 kg. Compute its void ratio.
For a falling head permeability test, the following are given: length of specimen is 360 mm, area of specimen is 70 cm2 , and hydraulic conductivity of soil specimen is 0.165 cm/min. what should be the area of the stand pipe for the head to drop from 700cm to 360cm in 7 mins? compute the seepage velocity under the test condition if the soil specimen has a void ratio of 0.55 in cm/sec compute the head difference at time equal to 5 minutes?