Current Attempt in Progress When a hydrometer (see the figure below and in the Video) having a stem diameter of 0.30 in. is placed in water, the stem protrudes 3.15 in. above the water surface. If the water is replaced with a liquid having a specific gravity of 1.09, how much of the stem would protrude above the liquid surface? The hydrometer weighs 0.042 lb.

Current Attempt in Progress When a hydrometer (see the figure below and in the Video) having a stem diameter of 0.30 in. is placed in water, the stem protrudes 3.15 in. above the water surface. If the water is replaced with a liquid having a specific gravity of 1.09, how much of the stem would protrude above the liquid surface? The hydrometer weighs 0.042 lb.

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter9: Mass And Mass-related Variables In Engineering

Section: Chapter Questions

Problem 37P

See similar textbooks

Similar questions

Calculate the velocity of water running in a pipe having a velocity head of 0.8 feet.
Consider incompressible , frictionless flow of a fluid in a horizontal piping. The pressure and velocity of a fluid is measured to be 150 kPa and 1.25 m/s at a specified point. The density of fluid is 700 kg/m^3. If the pressure is 140 kPa at another point, the velocity ( in m/s )of the fluid at that point is Show FBD and choose the correct answer below A. 5.49 B. 5.39 C. 5.19 D. 5.29
Show the complete solution. Kindly, include the necessary drawings ang label it properly based on given values. 10. A tank with a horizontal sectional area constant at 10m² and 4m high contains water to a depth of 3.5 m. The tank has a circular orifice 5 cm in diameter and located at its side 0.5 m above the bottom. If the coefficient of discharge of the orifice is 0.60, find the duration of flow through the orifice.
kindly help me with this problems INSTRUCTIONS: Solve the problems neatly and systematically. Use free-floating decimals in all your calculations and in expressing your answers. Box your final answers. 4. Calculate for the maximum height of the water stream that could rise from a nozzle pointed straight up. The nozzle is connected at the bottom of the tank having a water level of 15 m and the pressure above it is at 3atm gauge.
1. What is the rate of flow of water if the actual inside diameter is 1.5 inches and the flow pressure is 2592 lb/ft2 ? 2. Find the static head where the pressure is equal to 33 psi. 3. Calculate the velocity of water running in a pipe having a velocity head of 0.8 feet.
Read the question carefully and give me right solution according to the question.. Don't miss anything. Thank you At what speed in rpm must an open vertical cylindrical vessel, 2m in diam, 4m high and filled with water, be rotated on its own vertical axis in order that the effect of rotation will be to discharge sufficient quantity of water to uncover a circular area on the bottom of the vessel 1m in diameter. Determine also the volume of water spilled out. Draw the Figure.
PLEASE ANSWER QUESTION #1 ONLY, DISREGARD THE OTHER PROBLEMS GIVEN. SHOW COMPLETE SOLUTION. THANK YOU. An 8 ft diameter by 16 ft height vertical tank is receiving water (? = 62.5 lb/ft3) at the rate of 295 gal/min and discharging through a 4-in ID line with a constant speed of 6 fps. At a given instant, the tank is half full. Determine the following: QUESTION #1: What is the mass change in the tank? note: round off to 2 decimal place QUESTION #2: What is the water level in the tank 15 min. later? note: round off to 2 decimal place QUESTION #3: What is the volume change in the tank? note: round off to 2 decimal place
diameter of pipe = 200mm Cc = 0.61Cv = 0.97 Considering the figure, what is the flow of water?
A cylindrical tank having a diameter of 1.5 m and a height of 4 m is open at one end and close at the other end. It is placed below the water surface with its open end down. How deep below the water surface should the tank be placed if the depth of the water inside the tank is 1.8 m? a.6.0 cm b.5.90cm c.6.25cm d.7.0cm show your complete solution
Completely solve. Write legibly. Box the final answer. Water is flowing through a pipe 1/3 ft. inside diameter into a pipe 1'' in diameter at a rate of 12.62 lps. If the pressure in the 4'' pipe is 275.8 kPa, what is the pressure in the small pipe assuming no energy loss and friction head loss?
A venturi meter of 400 × 150 mm size is fixed in a horizontal pipe carrying water. The pressure gauge at entry read 137.34 kN/m^2 (gauge). The pressure at the throat was 37.5 cm of mercury (vacuum). Neglecting losses determine the flow rate. Specific gravity of mercury is 13.6. CHOICES: *0.632 m^3/s*0.349 m^3/s*0.945 m^3/s*0.141 m^3/s Please answer with complete and detailed solutions. thank you. ASAP
A rectangular tank that is 5/6 full, has a length of 26cm, height of 20cm and width of 15cm. If the water is transferred to another tank that is 18cm by 9cm by 30cm, how much water will overflow? (1cm^3 =1mL)