Current I (amperes), voltage V (volts), and resistance R (ohms) in a cırcuit are related by Ohm's Law, I = V/R. dl (a) Calculate dR if V is constant with value V = 24. R=6 dV (b) Calculate if I is constant with value I = 4. dR\R=6

Current I (amperes), voltage V (volts), and resistance R (ohms) in a cırcuit are related by Ohm's Law, I = V/R. dl (a) Calculate dR if V is constant with value V = 24. R=6 dV (b) Calculate if I is constant with value I = 4. dR\R=6

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

An office has a following dimensions : length = 20 m. width = 10 m. 1.) Ceiling to desk height is 2 m. 2.) Area to be illuminated to a general is 250 lux using twin lamp 32 watt CFLLuminaire with a SHR of 1.25. 3.) Each lamp has an initial output of 85 lumen per watt. 4.) Maintenance factor is 0.63, Utilisation factor is 0.69 Design a lighting system for this office by computing the following : 1. ROOM INDEX 2. INITIAL BARE LAMP FLUX
A meeting hall in an organization is to be provided with a lighting installation. The hall is 30 m × 20 m × 8 m (high). The mounting height is 5 m and the required level of illumination is 144 lm/m2. Design a lighting system for the hall with the given data. Lumens/watt for 200-W lamp = 12 and Lumens/ watt for 500-W lamp = 16. Utilization coefficient = 0.6 Maintenance factor = 0.75 space/height ratio=1 Using metal filament lamps, estimate the following: Flux Luman output per 200 W lamp Luman output per 500 W lamp Number of 500W lamps required Number of 220W lamps required Draw the spacing layout of these lamps State the reason if any of these 2 lamps cannot be arranged in the hall with the given specification. What is the significance of ‘room surface maintenance factor’ and ‘utilization factor’ in the lighting design
Objectives: Voltage drop measurements using resistors connected in series. The relationship between resistance value and voltage drop (Kirchhoff’s Second Law) Circuit components: 1 Plug-in board, DIN A4 576 74 1 STE resistor, 100 W, 2 W, 5% 577 32 1 STE resistor, 150 W, 2 W, 5% 577 34 1 STE resistor, 1 kW, 2 W, 5% 577 44 Power Supply: 1 AC/DC stabilizer 726 88 Connectors: 3 Pairs of connecting leads, red/blue, 50 cm 501 45 1 Set of 10 bridging plugs 501 48 Measurement Instruments: 1 Voltmeter, 10 V DC 1 Amperemeter, 10 mA DC Measuring the voltage drop across resistors…
Using thevenin theorem, determine the charge and discharge equivalent circuits for the Figure 4a. sketch in b and c respectively
current (A) Resistance (Ω) Voltage drop (V) 24cm 1 17.8 0.238 22cm 1 17.8 0.217 20cm 1 17.8 0.199 18cm 1 17.8 0.178 16cm 1 17.8 0.158 14cm 1 17.8 0.140 12cm 1 17.8 0.118 10cm 1 17.8 0.100 8cm 1 17.8 0.080 6cm 1 17.8 0.059 4cm 1 17.8 0.040 According to Ohm's law and the data above, the measured voltage V will be proportional to the length of the wire L with a slope b such that V= bL b=Iρ/(πD^2/4) ρ=b(πD^2/4)/ I Use Desmos to plot a graph of V versus the values of L . Is V linearly dependent on the length L? Find the best fit to the slope b and then calculate the resistivity of stainless steel.From this slope, what is the resistivity of stainless steel?
A meeting hall in an organization is to be provided with a lighting installation. The hall is 30 m × 20 m × 8 m (high). The mounting height is 5 m and the required level of illumination is 144 lm/m2. Design a lighting system for the hall with the given data. Lumens/watt for 200-W lamp = 12 and Lumens/ watt for 500-W lamp = 16. Utilization coefficient = 0.6 Maintenance factor = 0.75 space/height ratio=1 Using metal filament lamps, estimate the following: Draw the spacing layout of these lamps State the reason if any of these 2 lamps cannot be arranged in the hall with the given specification. What is the significance of ‘room surface maintenance factor’ and ‘utilization factor’ in the lighting design
An office space measures 50ft x 90ft with 16ft high walls. A 1.25 air changes per hours is desired for this space. Find the heat loss (in btuh) when the indoor temperature is 70°F and the outdoor temperature is 36°F. Select one: a. Q = 56,100 btuh b. Q = 44,880 btuh c. Q = 37,736 btuh d. Q = 75,900 btuh e. Q = 64,350 btuh
a) A 380V, 7.5kW electric water pump of power factor 0.8 lagging and efficiency of 85% will be wired by an armoured XLPE insulated copper cable. The circuit will be run on cable tray with three other similar circuits at an ambient temperature of 40℃. MCCB will be used as the overcurrent protective device for the circuit. The estimated length of the circuit for the machine is 50m. i) Determine the minimum rating of MCCB for the circuit, available MCCB rating are 25A, 30A, 40A, 50A ii) Determine the minimum cable size of the circuit if the allowable voltage drop of the circuit is 1.5% of the nominal supply voltage?
For the circuit given belowΒ1=200, β2=25, VBE1=VBE2=0.7 Va) Calculate the value of R1 when VEQ2=5 Vb) Calculate Avo
A workshop 100 m x 50 m is to be illuminated with intensity of illumination being 50 lux. Determine (a) the number of lamps required and (b) design a suitable scheme of lighting if coefficient of utilization = 0.9; maintenance factor = 0.7 and efficiency of lamps = 80 lm/W. Use 100-W lamps. [50 lamps]
Solve this question1)In concentrating solar power - central receiver, one of the following advantages is wrong comparing to parabolic troughSelect one:a. it requires less gross land area and less capital costb. None of thesec. No need for miles of tubes absorber tubes circulating HTFd. Less water usee. Achieves higher temperature and pressure2) The temperatures necessary to get sufficient efficiency to convert the earth’s heat to electrical power is:Select one:a. 160 °Cb. 230 °Cc. 130 °Cd. None of thesee. 200 °C
A small supermarket 20 m long by 15 m wide is to be illuminated to a level of 600 lx by 2400 mm 125 W fluorescent lamps having an efficacy of 65 lm/W. The maintenance factor is 0.85 and the coefficient of utilization is 0.6. Calculate the number of fittings required and show their positions on a scale plan. Calculate the total current taken by the lighting.