D = 250mm Determine the discharge in pipes 1, pipe 2, pipe 3 and pipe 6 in the system shown if the total head loss from A to B is 100m and friction factor for all pipes is 0.02. a) Discharge in pipe 1 is Blank 1 cu.m./s b) Discharge in pipe 2 is Blank 2 cu.m./s c) Discharge in pipe 3 is Blank 3 cu.m./s d) Discharge in pipe 6 is Blank 4 cu.m./s

D = 250mm Determine the discharge in pipes 1, pipe 2, pipe 3 and pipe 6 in the system shown if the total head loss from A to B is 100m and friction factor for all pipes is 0.02. a) Discharge in pipe 1 is Blank 1 cu.m./s b) Discharge in pipe 2 is Blank 2 cu.m./s c) Discharge in pipe 3 is Blank 3 cu.m./s d) Discharge in pipe 6 is Blank 4 cu.m./s

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Orifice meter with orifice cross-section 0.00785 m2 is inserted in a pipe of cross-section 0.0314 m2. The pressure gauges fitted upstream and downstream of orifice give reading of 19.62 N/cm2 and 9.81 N/cm2 respectively. Determine the value of discharge using Cd=0.6.
A cylindrical tank contains water at a height of 55mm as shown. Inside is a small open cylindrical tank containing cleaning fluid (s.g.-0.8) at a height h. The pressure Pb-13.4 kPa gage and Pc-13.42 kPa gage. Assume the cleaning fluid is prevented from moving to the top of the tank. (a) Determine the pressure Pa in kPa, (b) the value of h in mm, and (c) the value of y in millimeters
A cylindrical tank with vertical axis contains water. A 50 mm orifice is located at the side 0.60 m above the bottom of the tank and 1.50 m directly above the orifice is another orifice 75mm diameter. Cv is 0.98 and C is 0.61 for both orifices. Determine the: show complete solution thumbs up guaranteeda. h1 in metersb. Discharge in the lower orifice in lit/secc. Total discharge from the 2 orifices in lit/sec
1.) 38 lps of water flows through 90 m of a 6 inches nominal diameter, schedule 40, cast iron pipe. The pipe contains two 90o -standard elbows, two full-open gate valves, a full-open angle valve, and a backflow limiter (check valve). The discharge is located 6 m higher than the entrance. Consider the water viscosity of 0.01002 Poise.a) Determine the total head loss in the pipe line.b) What is the pressure difference between the two ends of the pipe? Use the Moody’s equation for the friction factor.
1. The horizontally lying device or fitting shown below connects three pipelines. Water (γwater = 9.81 kN/m3 ) enters the device through A with a speed VA = 8 m/s and a pressure PA = 70 kPa . Water exits through C at 9 m/s. Friction and minor head losses through the device are negligible. Note that B and C are not at atmospheric pressure. (a) Calculate the speed and flow rate of the water at B. Is the water flowing through B flowing into to the device or out of the device? (b) Calculate the pressures at B and C, PB and PC.
Water at 7 ft/s and 65 F flows in a 10 in schedule 40 pipe (inside diameter from Table A.III.1(SI) is 254.5 mm or 10.02 in from Table A.III.1(BU)). The pipe now bursts with an effective rupture area of twice the flow area of the pipe (ARupture = πD^2/2). Find the mass flow rate of water through the ruptured area. Assume that the flow velocity remains at 7 ft/s after the pipe ruptures. [Ans.: 239 lbm/s].
A 30m long, 20mm diameter steel pipe is used to drain an oil tank determine the discharge when the oil level in the tank is 4m above the exit of the pipe. Neglect minor losses, (assume f = 0.12)
A.) The loss factor for a 90 degree elbow is: B.) The total form friction head loss in ft is C.) The actual shaft work needed (since pump efficiency is only 60%) in horsepower or hp is: A centrifugal pump takes brine from the bottom of a supply tank and delivers it into the bottom of another tank. The brine level in the discharge tank is 150 ft above that in the supply tank. The line between the tanks is 600 ft of 4-in. Schedule 40 pipe. The flow rate is 400 gal/min. In the line are two gate valves, four standard tees, and four ells. What is the energy cost for running this pump for one 24-h day? The specific gravity of brine is 1.18, the viscosity of brine is 1.2 cP, and the energy cost is $400 per horsepower-year on a basis of 300 d/yr. The overall efficiency of pump and motor is 60 percent.
Pipes 1,2, and 3 having diameter of 150mm. 200mm and 250mm and leading from reservoir A, B, and C respectively join at a common point. All pipes are new cast iron (C=120) and each is 500m. If the water level in reservoir A is 1.80m than that in B and 4.8m higher than that in C. a) Calculate the discharge in pipe 1.b) The head loss in pipe 2c) The discharge in pipe 3 ** Need asap pls. Thank you.
Determine the available NPSH for the system shown in Fig. 13.38 (b). The fluid is water at 80°C and the atmospheric pressure is 101.8 kPa. The water level in the tank is 2.0 m below the pump inlet. The vertical leg of the suction line is a DN 80 Schedule 40 steel pipe, whereas the horizontal leg is a DN 50 Schedule 40 pipe, 1.5 m long. The elbow is of the long-radius type. Neglect the loss in the reducer. The foot valve and strainer are of the hingeddisk type. The flow rate is 300 L/min.
As shown in the figure below, the smaller pipe is cut off a short distance past the reducer so that the jet springs free into the air. Compute the pressure at 1 in psi if Q = 5 cfs of water. D1 = 12 inches and D2 = 4 inches. Assume that the jet has the diameter D2, that the pressure in the jet is atmospheric, and that the loss of head from point 1 to point 2 is 5 ft of water.
Fluid mechanis Read the question carefully, give me right solution The head loss (hf) in a 1200mm x 600mm pipe (therefore, non-circular) conveying water is estimated to be 0.04m for every 1 meter of its total length. If the said pipe is filled with water and its friction factor f = 0.032, what should be the discharge Q?