Solve it correctly please. I will rate accordingly. Suppose that F= 1000 lb. (Figure 1)Figure1 of 110 ft10 ft10 ftDetermine the force in member (AD BD, CD) of the three-member space truss.

Answered: Image /qna-images/answer/1840072a-1ba3-4404-acfe-743822ac328b.jpg

Answered: D 5 f 10 ft 10 ft 10 ft

Engineering

Mechanical Engineering

D 5 f 10 ft 10 ft 10 ft

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter5: Three-dimensional Equilibrium

Section: Chapter Questions

Problem 5.26P: The figure shows the FBD of a portion of the space truss shown in Fig. P5.25. Use this FBD to find...

See similar textbooks

Related questions

Q: grams, and determine the length s of length. angular displacement B1, in deg ngular displacement B2,…

A: L= 16681 β=68 degree = β 1 + β2 L1= 0.298 (a) → L= L1+ L2 L 2 =L-L1= 1661-0.298 = 1660.702…

Q: 45° FR F 75° 60 200 lb Using the sine rule, we have: O a F- 200lb Ob F- 273lb Oc F=189lb O d. F=…

Q: A damping force affects the vibration of a spring so that the displacement of the spring is given by…

A: given,

Q: A gas storage cylinder in an ordinary chemical laboratory measures 3.9 cm wide and 16. cm high. This…

A: Given: Initial Volume:

Q: An experiment on the life of a cutting tool at different cutting speeds are given bellow Speed v…

A: Given: To find: To find a relation between v and T where v is cutting speed T is tool life

Q: Two parallel shafts, 36 inches apart are connected by a belt drive. The driving pulley rotates at…

Q: he answer in M1 is 4283.29lb, can you show me how to get this answer

Q: What is the weight of 12 kilogram object, expressed in lbf?

A: Given data Weight is 12 kg

Q: 5. To draw a line with 70 length and * inclined in 35 degree we use L;(35,0) ; @ 35 < 70 L;@35;<…

A: Given that, Length of line is 70 And degree is 35° From option is can seen that it is to be draw…

Q: Q.3 In a bushmandrel system, a bush was turned on a mandrel. The mandrel diameter in millimeter is…

Q: A fluid having a specific gravity of 0.869 and dynamic viscosity of 0.0814 Pa-s flows through a cast…

A: Given:

Q: 2. From the given figure below, solve for the bar Y from the reference line. (choose the nearest…

Q: 2. Determine the reading on the vernier scale as indicated by the arrows. 25 30 35 40 10 20 30 40 50…

A: Least count of Vernier caliper = 0.02 mm

Q: If compounding is weekly (consider there is 52 weeks in one year), what nominal rate will make the…

Q: u =0 UnitsTm/s^ 2 umberT-7.4 7.4 j UnitsTm/s^ 2 umber -0.88 f you would like to Show Work for this…

A: Givenmass of slab m1=40kgmass of block m2=9kgbetween block and slabcoefficient of static friction…

Q: F3 = 750 N 45° 5 30° F2 = 625 N F = 850 N

Q: A flight conveyor of dimensions 3 and 2 ft are moving at a speed of 87 fpm. The conveyor handles…

Q: A steel pipe has an inside diameter of d = 250 mm and an outside diameter of D = 268 mm. The length…

Q: what is the present worth of 54000 due in five years if money is worth 11% and is compounded semi…

Q: On the attached drawing 11A017, what is the depth of the dovetail slot? All abbreviations are…

A: The drawing for dovetail slot is given as,

Q: (b) 1489.5m³ (C) 128

A: given:bore diameter d=68mmstroke length l=75mm

Q: The steel shaft with two different diameters rotates at 4.9 Hz. The power supplied to gear C is 54.1…

Q: 1. Determine the cylinder displacement and engine displacement of an engine having six cylinders…

A: given data bore diameter = 102 mm = 0.102m stroke length = 120mm =0.120m number of cylinders =6…

Q: Assignment 8.2: Measurements and Tolerances (continued) 11. A toy company manufactures wooden blocks…

A: Consider the side of cube have measure with error of (4.5±0.1)cma. Calculate maximum surface areathe…

Q: a, in mm (round off to one decimal place), such that maximum actuating force P is 2000 N, is

A: Given data; FBD of drum,

Q: An engine has four cylinders of 68 mm bore and 75 mm stroke. The cubic capacity of the engine is (a)…

Q: Given data : Maximum principal stress=100 Mpa Minimum principal stress=20 MPa Determine maximum…

A: Given data, σ1=100 MPa σ2=20 MPa Required τmax

Q: A fluid enters the boiler tube of constant inside diameter of 22.6 mm at 70 bar and 65 degC. The…

Q: Compute the piston displacement in cubic meter for every quarter of an hour of a single-stage,…

A: The piston displacement is 31.14 m3.

Q: How are you getting 16 mm at the end for an answer , "HX83=219X10^3/164.909".................is…

A: Stress, σ = FA F = 219 kNσ = 164909 kPa Substituting the values 164.909=219AA = 0.001132 m2 One…

Q: Two parallel shafts, 30 inches apart are connected by a belt drive. The driving pulley is 20 inches…

Q: . The changes in dimension caused by an increase in temperature of 80°C for the: Outside diameter…

Q: Thermal efficiency of a power cycle is 0.8. For the cycle, Qout = 250 kJ. Determine Qin in kJ.

A: Answer: Oin = 1250 kJ.

Q: A hollow steel shaft has an outside diameter of 3 inches and an inside diameter of 1.5 inches. What…

Q: the value of B is

A: Given; Maximum value of W to avoid buckling of the beam isobtained as βπ2EI, where, πis the…

Q: QUESTION 5 Find Fa if: Fb = 404 db = 0.8 da = 0.3 e = 21 Fa Fb Provide answer to zero decimal…

A: Fb=404 , db=0.8, da=0.3, θ=21° ;Let Reaction at support is Rx and Ry ;So the force resolution in x…

Q: The most powerful engine available for the classic 1963Chevrolet Corvette Sting Ray developed 360…

A: Given Data : displacement = 327 in3

Q: 40⁰ 12 650 N 5 Figure 1 30⁰ 1000 N

A: According to Bartleby guidelines, we are allowed to solve only a single problem.Please post the rest…

Q: Ballast (a) Find the height h(t) (in feet) of the ballast from the ground at time t. Hint: h'(t) =…

Q: Q. The value of poission's ratio (1/m) is never greater than- a) 0.05 b) 0.5 c) 1.5 d) 5.0

A: The range of Poission's ratio is given between -1 to 0.5. That means, Poisson's ratio cannot be…

Q: The acceleration due to gravity at the surface Mars is 3.7 ms/s. A stone throw upward on Mars…

A: Answer : Given data: a=3.7 m/s2h=24.1 m Need to determine the initial velocity of the stone.

Q: 1000 B00 600 400 200

A: As we knowDuctility is the percent elongation reported in a tensile test is defined as the maximum…

Q: A centrifugal pump discharged 20 L/s against a head of 17 m when the speed is 1500 rpm. The diameter…

Q: A spring requires 2 J to stretch from 1 m to 6 m. An additional 4 J is required to stretch the…

Q: In a limit system, the following limits are specified for a hole and shaft assembly: Hole = 70…

A: Given: Dimensions of,Hole=70+0.00+0.04mmShaft=70-0.08-0.04mm

Q: T = 20°C B (rough) L = 0.5m

A: Given data as per qustionTs=100°CT∞=20°Cu∞=14m/sL=0.5Rex=5×105

Q: ᴀ ᴘᴜᴍᴘ ᴅᴇʟɪᴠᴇʀꜱ 0.3 ᴍ3/ꜱ ᴀɢᴀɪɴꜱᴛ ᴀ ʜᴇᴀᴅ ᴏꜰ 200 ᴍ ᴡɪᴛʜ ᴀ ꜱᴘᴇᴇᴅ ᴏꜰ 2000 ʀᴘᴍ. ꜰɪɴᴅ ᴛʜᴇ ꜱᴘᴇᴄɪꜰɪᴄ ꜱᴘᴇᴇᴅ

A: Given data: Q=0.3 m3/sH=200 mN=2000 rpm Need to determine the specific speed.

Q: 1. From the given figure below, solve for the bar X from the reference line. (choose the nearest…

Question

100%

Solve it correctly please. I will rate accordingly.

Suppose that F= 1000 lb. (Figure 1)
Figure
1 of 1
10 ft
10 ft
10 ft
Determine the force in member (AD BD, CD) of the three-
member space truss.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The figure shows the FBD of a portion of the space truss shown in Fig. P5.25. Use this FBD to find the force in member BD.
Continuous cable A DB runs over a small friction less pulley al D to support beam OABC, which is part of an entrance canopy for a building (see figure}. The canopy segment has a weight W = 1700 lb that acts as a concentrated load in the middle of segment AB. (a) What is the maximum permissible value of load P at C if the allowable force in the cable is 4200 lb? (b) If P = 2300 lb, what is the required diameter of pins A, B, and D? Assume that the pins are in double shear and the allowable shear stress in the pins is 10 ksi.
A steel cable with a nominal diameter of 25 mm (see Table 2-1) is used in a construction yard to lift a bridge section weighing 38 kN. as shown in the figure. The cable has an effective modulus of elasticity E = 140 GPa. (a) If the cable is 14 m long, how much will it stretch when the load is picked up? (b) If the cable is rated for a maximum load of 70 kN, that is the factor of safety with respect to failure of the cable?
For the truss given below, it is desired to determine the normal efforts that act on the members, so that, thus, possible constraints for its design are possible. Consider that at point A there is a second gender support; and at point D, a first-class support. As this is asked: what is the effort acting on bar AB? Is it guidance or assessment?Source: Hibbeler (2004, p. 588). HIBBELER, R. C. Resistance of Materials. 5. ed. Rio de Janeiro: Technical and Scientific Books Publisher, 2004. Question 1 options: a) A compression force of 100 kN acts on bar AB. B) A tensile effort of 100 kN acts on bar AB. c) A compressive force of 141.42 kN acts on bar AB. d) A compression force of 200 kN acts on bar AB. e) A tensile effort of 141.42 kN acts on bar AB.
Find the residual forces acting in a truss with members AC=1000N (T), EG=520N (T), and FH=1200N (C) as indicated in Figure 2. Determine the loads P1, P2, and P3 as well.
Find the residual forces acting in a truss with members’ AC=1000N (T), EG=520N (T), and FH= 1200N (C) as indicated in Figure 2. Determine the loads P1, P2, and P3 as well.
Find the residual forces acting in a truss with members’ AC=1000N (T), EG=520N (T), and FH= 1200N (C)as indicated in Figure 2. Determine the loads P1, P2, and P3 as well.
*Consider the truss shown in (Figure 1). Suppose that F = 9.5 kN.* Pt A: Determine the force in member HI of the truss. Pt B: Determine the force in member FI of the truss. Pt C: Determine the force in member EF of the truss.
Find the residual forces acting in a truss with members AC=1000N (T), EG=520N (T), and FH=1200N (C) as indicated in Figure 2. Determine the loads P1, P2, and P3 as well. Use four decimal places.
using the method of sections , analyse the truss shown in figure 8 below reguarding forces in menbers ED , DF AND FC .
*Consider the truss shown in (Figure 1). Suppose that F1 = 6 kN and F2 = 8 kN* . Pt A: Determine the force in member BE and state if the member is in tension or compression. Pt B: Determine the force in member EF and state if the member is in tension or compression. Pt C: Determine the force in member CB and state if the member is in tension or compression.
Table 1 : F= 585 lb, P = 215 lb, X= 5 ft, Angle of the inclined bars of truss = 30°