d) Suppose, you are required to design a FIR low-pass filter of order 64 with cut-off frequency 100Hz to remove high frequency noise from acquired EEG recordings through a single channel EEG headset provided by Neurosky with a sampling rate of 256 Hz and an ADC resolution of 8-bit. In this regard, the pass-band and stop-band tolerances of that filter are given in terms of relative specifications, i.e. 0.5dB and 50dB, respectively. However, for your design, you are required to find the absolute specifications, i.e. determine the pass-band tolerance and the stop-band tolerance for the same FIR filter.

d) Suppose, you are required to design a FIR low-pass filter of order 64 with cut-off frequency 100Hz to remove high frequency noise from acquired EEG recordings through a single channel EEG headset provided by Neurosky with a sampling rate of 256 Hz and an ADC resolution of 8-bit. In this regard, the pass-band and stop-band tolerances of that filter are given in terms of relative specifications, i.e. 0.5dB and 50dB, respectively. However, for your design, you are required to find the absolute specifications, i.e. determine the pass-band tolerance and the stop-band tolerance for the same FIR filter.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Sketch the Vout/Vin versus frequency characteristics of an LC Bandpass filter. Show flc and fhc on the sketch and explain how they are defined. On this sketch, show the bandwidth (BW) of the filter and explain how it is defined.
For the filter: a) Determine type of filter and the cut-off frequency (Fc). Determine the peak voltage at the cut-off frequency (Fc). b) Find GAIN (Vo/Vi) at f = .1*Fc . Find GAIN (Vo/Vi) at f = 10*Fc . c) Determine the frequency at which GAIN = .4 (i.e., Vo = .4*Vi) . Draw the “Frequency Response Plot” in “Log-Log” format .
a) Consider the system shown in Figure 3(a). An input signal vm(t) is multiplied by a complex exponential signal e10nt The output signal v,(t) is fed into a low pass filter (LPF) with cut-off frequency wc. The input signal Vm(@) and the output signal V.(@) are as shown in Figure 3(b) and (c), respectively. i. Write the mathematical equation for signal in Figure 3(b). ii. Sketch signal, V,(@). iii. Based on the given V, (w), write the mathematical expression of the LPF, H(@) and state its cut off frequency, wc. iv. Sketch the output of LPF, V(@), if the cut off frequency of LPF is 10. v:(t) LPF Vm(t) vo(t) H(@) ej10nt (а) |Vm (@)| IV,(@)| 10 8 6. 3 -20715T-10T-5n 5n 10n 15n 20n -57 (b) Figure 3
Draw the circuit diagrams of a first and a second order band pass filter and indicate its lower and upper cut off frequencies. Do the same for band stop filter. thanks in advance! ..
A channel having a bandwidth of 1 kHz, the power of signal is 10 W and the power of noise is 5 W. Determine the channel capacity. Or: A channel having a bandwidth of 1 kHz and Signal to Noise Ratio (SNR) is 2. Determine the channel capacity.
A) Write the equation for the small-signal gain function ???????for the followingop-amp circuit B) What kind of filter is this circuit? C)Write the equation for the cutoff frequency of the filter D) Sketch the Frequency Response of the system.
Describe the importance of using Bandpass filters in BFSK noncoherent demodulator.
Report: 1. How would you design 3™-order low pass butter worth filter, explain the design procedure? 2. What are the main disadvantages of designing the band reject filter, mentioned above? Suggest a butter circuit design. 3. In modern active filter design, the capacitor can be removed to give an all active R-filter. Suggest a 2™-order R-filter, what are the advantage and disadvantages of such filter? 4. What are the main applications of the above mentioned filters?
Ques2: What is the Low pass filter? Drive an expression of gain of Active Low and draw its frequency response.
Discuss and explain the operation of filter
Discuss the meaning of the quality factor and how band-pass filters are classified.
show step by step with diagrams and formula on how to arrive at the output waveform for a center-tapped full-wave with filter capacitor