Darcy Experiment A set-up of Darcy Experiment involves measuring the pressure head at two piezometers separated a distance, L. Given the set-up shown, determine the hydraulic gradient if the hydraulic head at (1) is 66 cm, hydraulic head at (2) is 54 cm, and the travel distance is 100 cm. 0.12 O -0.12 O 8.33 |(1) O -8.33

Darcy Experiment A set-up of Darcy Experiment involves measuring the pressure head at two piezometers separated a distance, L. Given the set-up shown, determine the hydraulic gradient if the hydraulic head at (1) is 66 cm, hydraulic head at (2) is 54 cm, and the travel distance is 100 cm. 0.12 O -0.12 O 8.33 |(1) O -8.33

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter7: Seepage

Section: Chapter Questions

Problem 7.1P

See similar textbooks

Similar questions

An 83-mm-diameter siphon is drawing oil (SG = 0.85) from an oil reservoir, as shown in the figure. If the velocity of flow in the pipe is 'v', the head loss from point 1 to point 2 is 6v2/2g, and the head loss from point 2 to point 3 is 2v2/2g. Find the absolute pressure (in kPa) at point 2. Use atmospheric pressure, Patm = 102 kPa. Use y1 = 5 m., and y2 = 7 m.
Water at 60°F is siphoned between two tanks as shown in Figure P8.27. The connecting tube is 2.0 in. diameter smooth plastic hose 20 f t long. Find the volume flow rate and the pressure at point P, which is 8 f t from the entrance to the tube. Ignore minor losses. (To begin, assume a friction factor, then iterate.)
With the chamber-pipe system in the figure, the ideal fluid (water) taken from the infinitely sized chamber A is poured into the atmosphere with a 40 cm fixed diameter BCDEF pipe. Since zB=29, zC=10, zD=28.5, zE=5 and zF=28 meters according to the comparison plane;a) Calculate the flow of the system.b) Draw the relative load (energy) and piezometer lines of the system.c) Determine where the greatest pressure will be observed throughout the system and calculate its relative value.
1. An orifice in the side of a vertical tank discharges oil (sp. gr. = 0.82) under a head of 4.0 m. and 25 KPa pressure acting on the surface of the oil. If the diameter of the orifice is 5 cm, the coefficient of contraction is 0.62, and the head lost on the orifice is 45 cm, determine the discharge, coefficient of velocity, and the coefficient of discharge.
A venturi meter with a throat diameter of 100 mm is fitted in a vertical pipeline of 200 mm diameter with oil of specific gravity 0.88 flowing upwards. Two pressure gauges are fitted at tapping points, one at the throat and the other in the inlet pipe 320 mm below the throat. The difference between the 2 gage pressure readings is 28 kPa. (a) Determine the flow in m^3/s neglecting head losses (b) Working from Bernoulli's equation, determine the difference in levels (in mm) between the two limbs of a mercury manometer if it is connected to the tapping points and the connecting pipes are filled with the same oil Draw illustrations Use 3 decimals
Water at 20°C ( ρ= 999.7 kg/m3 and μ=9.7720 x10-4 kg/m · s) is flowing steadily in a hexagonal cross sectional pipe b=1.5cm, 20-m-long at an average velocity of 1.2 m/s. Determine: (a) Hydraulic diameter. (b) The pressure drop. (c) The head loss. (d) The pumping power requirement to overcome this pressure drop.
The pressure gauges are inserted at A and B in a vertical pipe converging water. The diameters at A and B are 150mm and 75mm respectively. The point B is 2.3m below point A. When rate of flow down the pipe is 0.021m³/s. The pressure at B is 117.72 KN/m² greater than at A. The losses in pipe between A and B are expressed as(KVa²/2g) where Va is velocity of A. Find the value of K. If the pressure gauges at A and B are replaced by tubes filled with water and connectef to a u-tube containing Hg(SHg=13.6) calculate the value of the reading manometer.
A cylindrical tank 2m in diameter and 15 meters high is filled with liquid Z. A pressure gage at elev 10 m at the side of the tank reads 105 kPa. another gage at elev 6m reads 138 kPa. compute the (a) specific weight of the liquid and (b) density of the liquid.
An open rectangular tank 6 m long, 3 m wide and 2m deep contains water to a depth of 1 m. It is accelerated horizontally at 2.5 m/s2 in the direction of its length. Determine the minimum pressure intensities at bottom Unit of the Correct Answer: kPa Group of answer choices 12.3 2.31 0.123 1.23 .
The flowrate of the flow is 0.20 + a/10 m3 /s in a pipe placed on a horizontal plane. The pipe diameters are D1= 0.30 m and D2= 0.20. Please find the force acting to the pipe by the flow. The gauge pressure at (1) is p1 =200 + b*10 kN/m2 . (g=9,81 m/s2, g=10kN/m3 ) a= 4 b=3
Two tanks A and B are connected by a pipe 30 m long. The first 21 m has a diameter of 75 mm and then suddenly reduced to 50 mm for the next 9 m. The difference of levels between the tank water levels is 2.40 m. The pipe frictional coefficient is f = 0.005 and contraction coefficient at sudden change in area is 0.58. Find the rate of flow.
The container is partially filled with oil. Water and air as shown. Determine the pressure at A, B and C assuming Pwater=1000kg/m^3 and Poil=830 kg/m^3