Delermine une angie beiween une resuilant iorce anu ne x axis. Replace the loading on the frame by a single resultant force. Suppose that F = 300 N É = 500 N, F = 900 N , and F = 250 N . (Figure 1) Express your answer using three significant figures. • measured clockwise from the positive x axis 0 = 47,4 Submit Previous Answers All attempts used; correct answer displayed Part C Figure 1 of 1 > Specify where its line of action intersects a vertical line along member AB, measured from A. Express your answer to three significant figures and include the appropriate units. Enter positive value if the line of action intersects a vertical line AB above point A and negative value if the line of action intersects a vertical line AB below point A. 0.5 m 1 m F, B ? [0.5 m y = Value Units F1 1.5 m Submit Request Answer 1'm Provide Feedback Next >

Delermine une angie beiween une resuilant iorce anu ne x axis. Replace the loading on the frame by a single resultant force. Suppose that F = 300 N É = 500 N, F = 900 N , and F = 250 N . (Figure 1) Express your answer using three significant figures. • measured clockwise from the positive x axis 0 = 47,4 Submit Previous Answers All attempts used; correct answer displayed Part C Figure 1 of 1 > Specify where its line of action intersects a vertical line along member AB, measured from A. Express your answer to three significant figures and include the appropriate units. Enter positive value if the line of action intersects a vertical line AB above point A and negative value if the line of action intersects a vertical line AB below point A. 0.5 m 1 m F, B ? [0.5 m y = Value Units F1 1.5 m Submit Request Answer 1'm Provide Feedback Next >

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.4.22P: , Solve the preceding problem using the numerical data: /) = 90mm, h = 280 mm, d = 210 mm, q = 14...

See similar textbooks

Similar questions

, Solve the preceding problem using the numerical data: /) = 90mm, h = 280 mm, d = 210 mm, q = 14 kN/m, and L = L2 m.
The bearings at A and D exert only y and z components of force on the shaft as shown in Fig 7. Determine the smallest diameter of the shaft using maximum shear stress hypothesis theory if the allowable stress is 100 MPa.
Three rods jointly support a 8kN load. Assumingthat there was no stress in the rods before theload was applied, find the stress in each rod.θ = 25oα = 20oProperties:Modulus ofElasticityCrosssectionalAreaSteel 200 GPa 250mm2Bronze 83 GPa 250mm2
Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown. The normal stress in aluminum rod (1) must be limited to 20 ksi, the normal stress in brass rod (2) must be limited to 24 ksi, and the normal stress in steel rod (3) must be limited to 12 ksi. Determine the minimum diameter required for each of the three rods. Assume P = 8 kips, Q = 5 kips, R = 20 kips and S = 28 kips. Calculate F1, F2, F3 and..
a. Draw the Free Body Diagram (F.B.D), considering a section perpendicular to thelongitudinal axis. Please clearly show that sectional plane along with the upperportion of the body. b. Shall there be any shear and/or moment as an internal loading on the section,which you already have drawn? c. Develop the equilibrium equation. d. Write down the compatibility equation. e. Determine the average normal stress in the aluminum and the bras. PARTS D & E ONLY PLEASE
Three rods jointly support a 8kN load. Assumingthat there was no stress in the rods before theload was applied, find the stress in each rod.θ = 25oα = 20o Properties:Modulus ofElasticityCrosssectionalAreaSteel 200 GPa 250mm2Bronze 83 GPa 250mm2 L = 2.75 m
ts=600g, TL=18pounds , angle=780degree ,can you please find the solution and free body diagram
For the indicated part. What would be the maximum torque that can be applied to the indicated part if the bar is solid, made of steel, with a diameter of 5 cm, L = 2m and the total angle of torsion in the length cannot exceed 2 degrees? Assume G = 80 GPa. (Hint: Twist angle has to be in radians to use in formula)
The aluminum bar has a 40mm diameter and 600mm length. It is held stationary at the origin on the left end. On the right end is a wrench that is 70i+220j mm from the connection to the rod to where the force is applied. At that point, a force of -7000i+800j N is applied. a) What is the mass of the bar? b) What is the moment applied by the wrench? c) What is the maximum normal stress due to this moment? d) What is the yield factor of safety for this stress?
The schematic of a punch and die for punching washer isshown. Determine the force F needed to punch outwashers with thickness of 5mm, inside diameter of 15 mmand outside diameter of 25mm. The average shearstrength of the plate is 30 MPa and average compressivestress in the puncher is 65 MPa. Answer: F =___________________
Two vertical steel wires each 0.05 in. diameter and 48in. long support a light rod over a span of 12 in. A concentrated load of 60 lbf is then applied vertically downwards at a point 4 in. from one of the wires. Determine the load, stress and extension on each wire and the angular displacement of the rod from the horizontal assuming it does not bend. Use E = 29,000 ksi.
The flywheel causes a completely reverse bending on the shaft and the factor of safety is 2, determine: a. The ultimate tensile strength ( Su) of the material if the Yield strength (Sy) is 0.6 of Ultimate strength. b. The fatigue life of the shaft given the fatigue strength (S) is equal to 0.8Su and endurance Strength (Se) is equal to 0, 5Su, given the minimum stress is 0.3 of Maximum stress c. Draw the S - N diagram