Describe the operation of heat-pump cycle (optimal case only) in Figure.2 and the its thermodynamics properties, by constructing a P-h and T-S plots showing the following: a) The processes and indicate their types (isothermal, isobaric or isentropic) b) The refrigeration effect (RE), heat of compression (HOC), and heat of rejection (HOR).

Describe the operation of heat-pump cycle (optimal case only) in Figure.2 and the its thermodynamics properties, by constructing a P-h and T-S plots showing the following: a) The processes and indicate their types (isothermal, isobaric or isentropic) b) The refrigeration effect (RE), heat of compression (HOC), and heat of rejection (HOR).

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter8: Natural Convection

Section: Chapter Questions

Problem 8.46P

See similar textbooks

Similar questions

If 14 gpm of water is flowing through an open-loop heat pump with a temperature difference of 7F, how much heat in Btu/h is being absorbed or rejected in the heat pump? Show all work and units.
An important factor (or factors) involving water quality with regard to open-loop heat pump systems is(are) A. water temperature. B. water cleanliness. C. water volume in gpm. D. all of the above.
In the following setup, heat engineoutput is utilized to run a refrigeration cycle.(a) Calculate QL1, (b) Is the heat enginereversible, irreversible or impossible? (Brieflyexplain), (c) Calculate QH2, and (d) Is therefrigeration cycle reversible, irreversible orimpossible? (Briefly explain). Clearly explaineach step!
A simple – vapor compression cycle develops 13 tons of refrigeration. Using ammonia as the refrigerant and operating at a condensing temperature of 24deg-C and evaporating temperature of -18deg-C find the following: refrigerating effect per unit of refrigerant, circulation rate in kg/min, power requirement in hp, and coefficient of performance. Use the spreadsheet to solve this problem.
1. In a steam power cycle, steam enters the turbine at 30bar with the following different conditions and leaves at 1bar. Calculate Carnot efficiency, Rankine efficiency, condenser heat flow in kW assuming mass flow rate of steam as 9.5kg/s and steam rate for each case considering the pump work. (ii)Wet with 0.95 dryness (iii) Superheat at 550°C
For ideal cycle and engine, calculate a) the thermal efficiency, b) the engine steam rate, c) actual condition of the exhaust steam, and d) steam flow rate in kg/h for 1.1 MW generator output at 94% efficiency
Perform a parametric study for a steam power plant operating between pressures of 7 MPa and 7 kPa on an ideal Rankine cycle. Use feedwater heater pressure as the variable. Produce plots similar to Figure IIb.2.3 for such parameters as fraction of the steam extraction, pump work, and turbine work.
Find the mean effective pressure of the thermodynamic cycle shown in the figure below.
A Rankine Engine-Generator unit receives 27,000 kg/hr of steam at 1.2 MPa and 150°C and exhausts to a condenser temperature of 22 C. Brake steam rate is 4.74 kg/kW-hr, mechanical efficiency is 90 % and generator efficiency is 94 %. Determine: a) ideal cycle thermal efficiency, b) indicated engine efficiency, c) generator output (kW), d)the condition of turbine actual exhaust
1st Step: Evaluate the performance of the Refrigerator 1.Refrigerator 1 operates as a reverse Carnot cycle using R-717 as the refrigerant at aflow of 1.8 kg/s. The condensing and evaporating temperatures are 25 °C and -5 °C, respectively.To evaluate the performance of Chiller 1, you must determine the following performance parameters:project:a) Rate of heat elimination in the condenser (Q );b) The power of the compressor;c) The COP of the cycle.For the energy balance, make the following considerations:- Permanent regime;- Variation of kinetic energy and potentials are negligible;- Compressor and turbine operate adiabatically;- Evaporation and condensation steps do not involve work. Please, make it typeable, written in virtual text, do not do it by hand and do not take a photo, it interferes with the understanding of the lyrics.
Rankine cycle for initially dry saturated steam at 150 psi, condenser pressure of 2 psi. Find the work of cycle in Btu and ft-lb. Also compute the cycle efficiency.Note of the following data from the steam table:At 150 psia: Tsat=358.4 deg. FVf=0.0180 ft3/lb, vg=3.016 ft3/lb; uf=330.2 Btu/lb; ug=1111.2 Btu/lb; hf=330.5 Btu/lb; hfg=863.6 Btu/lb; hg=1194.1 Btu/lb; sf=0.5138 Btu/lbR; sfg=1.0556 Btu/lbR; sg=1.5694 Btu/lbRAt 2 psia: Tsat=126.04 deg. FVf=0.016 ft3/lb, vg=173.75 ft3/lb; uf=94.02 Btu/lb; ug=1051.8 Btu/lb; hf=94.0 Btu/lb; hfg=1022.2 Btu/lb; hg=1116.2 Btu/lb; sf=0.1749 Btu/lbR; sfg=1.7451 Btu/lbR; sg=1.9200 Btu/lbR
Derive the MEP for dual cycle in terms of P1, rk, rp, k, and e.