Answered: Describe the series of box passes…

Engineering

Mechanical Engineering

Describe the series of box passes applied to hot rolled blooms to obtain square or round sections.

Welding: Principles and Applications (MindTap Course List)

8th Edition

ISBN:9781305494695

Author:Larry Jeffus

Publisher:Larry Jeffus

Chapter23: Fabricating Techniques And Practices

Section: Chapter Questions

Problem 11R: What is the difference between plate and sheet material?

See similar textbooks

Related questions

Q: What is the operation of parting?

A: Parting operation

Q: Major metal forming processes include ______ a rolling to reduce the thickness for making…

A: Metal forming is a manufacturing process used to change the shape of the metal work piece. Metal…

Q: DENTIFICATION: ___________1. It is also known as roll forming. ___________2. It is the most…

A: To identify the correct process

Q: Jhat types of Forming processes?

A: The different types of forming process are:- Rolling Wire drawing Tube drawing Extrusion Forging…

Q: Forms of bulk metal forming include all of the following except? Rolling Extrusion Forging Explosion

Q: city 8f steadily decrease from entrance to exit. ii. Rolling is most effective in the absence of

A: The velocity of the sheet increases from the entry of the roll to the exit of the roll. It helps in…

Q: Explain the disadvantages of Tube Drawing process in which mandrel is not used.

A: Given Data⇒Tube drawing ProcessNo use of mandrelProblem definition⇒Problem says Explain the…

Q: What are the main advantages of forging and explain forgeability.

A: Forging is a metal fabrication technique in which impact forces are imparted on metal so that the…

Q: Why are hot-rolled products generally limited to standard shapes and sizes?

A: Hot rolled products have a scaly surface with slightly rounded edges and corners. It requires a high…

Q: The flow rate of liquid metal into the downsprue of a mold = 1 liter/sec. The cross-sectional area…

A: GIVEN DATA - Q=1 lit/sec h=175mm A1=800mm2 WE HAVE TO CALCULATE BOTTOM AREA OF SPRUE

Q: How long does the Forging process take?

A: It takes about 3- 5 days of constant hammering. If we want some good and super fancy look it will…

Q: Discuss the differences between fusion and solid state welding t SIX (6) reasons why the plastic…

A: Solid State Welding - Two parts are integrated into this type of welding without heat which is the…

Q: Y san we possibly measure the drawability of sheet metal ?

Q: What processing method would you use to make a rigid plastic pipe that can be laid easily?

A: Given data What method to be used for making a rigid pipe.

Q: Tandem drawing of wires and tubes is necessary because; Surface finish improves after every drawing…

A: Given question 1 question 2

Q: Question 7 7.1 A component is designed to be hot forged in an impression die. The projected area of…

Q: In the direct extrusion method, the heated metal billet is placed into th die chamber and the…

A: Ans: In the direct extrusion method, the heated billet metal is placed into the die chamber, and…

Q: Derive a heat balance equation for a twin screw extrusion process

A: Write the expression for thermal penetration thickness. δt=4αt Write the circumferential width of…

Q: Question 2. It is reduced to 80 mm with forging by stacking a part with a height of 120 mm and a…

Q: A vertical gating system has a sprue height of 250 mm, one ingate located 150 mm below the mould top…

A: According to the Bernoulli's equation, the velocity of the fluid at any cross section which is…

Q: Suggest the optimum parameter setting or methods to obtain high quality moulded parts.

Q: Compare any ten major differences between Drawing process and Extrusion process

A: Following is the differences between Drawing process and Extrusion process- Extrusion Drawing…

Q: What two hot forming processes can convert steel skelp into pipe?

A: Steel pipes are made by two different processes. The overall production method for both processes…

Q: What is isothermal forming?

A: Isothermal Forming :-

Q: Explain with neat sketch of "Explosive forming" process.

A: Explosive forming is a process in which forces produced by an explosion are used to shape a…

Q: What is the advantage in casting turbine blades that have either highly aligned grain boundaries or…

A: Turbine blades are manufactured by casting by containing superalloys in them. These superalloys have…

Q: During pure bending, why there is no shear stress?

A: Bending - Bending of a beam is due to the moment load applied during the loading of the beam.…

Q: The flow rate of liquid metal into the downsprue of a mold = 1 liter/sec. The cross-sectional area…

Q: When are the thin-walled tubes of the noncircular cross-section often used to construct?

A: Thin-walled tubes are the thickness of the tube is less than 1/20th of the diameter of the tube.…

Q: (USCS units) A part is hot forged in an impression die. The projected area of the part, including…

A: Given data as per the question The projected area of the part, =17.3 in2 . After trimming, the part…

Q: Q16. A mug is to be made from alumina. Which forming method would be most suitable?

Q: A solid cylinder of diameter 100 mm and height 50 mm is forged between two frictionless flat dies to…

A: Given:Diameter of solid cylinder, d1=100 mmHeight of solid cylinder, h1=50 mmFinal height of solid…

Q: some examples about deep drwing?

A: deep drawing is a process in which complex shapes and seamless products are manufactured. A material…

Q: 9) Define the rolling resistance.

A: We are to define rolling resistance.

Q: Comparison factor Volumetric deformation Sheet metal work Surface area/volume ratio: High, Low Basic…

A: comparison factor volume deformation sheet metal work surface area/volume ratio; the area of…

Q: Ratio of soldification time of a cylindrical casting (Height=radius) of that of a cubic casting of…

Q: The hot rolling process is being widely used in the production of ,., structural sections plates…

A: Hot rolling: It is a type of manufacturing process in which metal is heated above its…

Q: O-in-thick slab is 10.0 ir eps in a hot rolling ope hickness. It is expected 3%ln each step. If the…

A: given:number of passes n=3t0=2reduction r=75%w0=10.92in

Q: In extruded products piping defect is usually associated with indirect extrusion. От F

Q: A typical plastic shopping bag made by blown film has a lateral dimension (width) of 550 mm. Assume…

A: Given:- Width=550mm Expanded from 1.5 to 2.5 times To find:- Die diameter size

Q: Tube Extrusion is an extension of the direct extrusion process where an additional arm is needed to…

A: Extrusion: in this process molten or liquid material is forced through a die so that the material…

Q: When is the shear formula?

A: The simplest formula is the ratio of Shear Force and the Area on which it is acting. That is, S =…

Q: Coupling will be used in the drive mechanism of the roles used in the Continuous Casting plant. The…

A: Flexible coupling is best suited to absorb these fluctuations.

Q: - Answer two of the following: ) State the types of sheet metal bending process and compare (in…

Question

Describe the series of box passes applied to hot rolled blooms to obtain square or round sections.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

When are the thin-walled tubes of the noncircular cross-section often used to construct?
Derive a heat balance equation for a twin screw extrusion process
Describe the defects found on the injection/ compression moulded parts with different temperatures or time setting. Discuss the possible causes for each case.
Suggest the optimum parameter setting or methods to obtain high quality moulded parts.
Show your full solution.
How do I begin this problem?
How long does the Forging process take?
What is the difference between plate and sheet material?
What two hot forming processes can convert steel skelp into pipe?
1. A component is designed to be hot forged in an impression die. The projected area of the product is 5800 mm2. During the forging process flashing is formed so that the area including the flash will be 8900 mm2. The part geometry is considered to be simple and the heated work material yields at 92 MPa. Calculate the maximum force required to perform the operation. 2. What are the advantages and disadvantages to forge a product through the open forging process, rather than to machine it from the same material?
Q#4: (b) Explain the disadvantages of Tube Drawing process in which mandrel is not used.
1. Write the requirements of good pattern.2. What is core venting? 3. Which process is called lost waxing method? Why? answer all the 3 parts