Design such a power supply with an input Voltage ranging from 10V to 15 V, and a limiting Resistor of 4.0 kΩ. Specifications of the Zener diodes are; VBr is 8 V and RZ is 100Ω. Your task is to obtain regulated output Voltage within the input voltage range.

Design such a power supply with an input Voltage ranging from 10V to 15 V, and a limiting Resistor of 4.0 kΩ. Specifications of the Zener diodes are; VBr is 8 V and RZ is 100Ω. Your task is to obtain regulated output Voltage within the input voltage range.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter18: Resistive-inductive Parallel Circuits

Section: Chapter Questions

Problem 8PP: In an R-L parallel circuit, ET=48 volts, IT=0.25 amps, R=320. Find XL.

See similar textbooks

Related questions

Q: each of the Zener diodes has a zener voltage of 5.0 V, what value will the positive output be…

A: Right Answer option B. 5.7 Volt

Q: 7. A yellow colored LED with a forward voltage drop of 2.1V is to be connected to a 5.0V stabilized…

A: 7) no specific questions is mentioned so I am solving Questions 7.

Q: 1. Design a half wave rectifier circuit for a resistive load 250N, voltage rating of 50V, with each…

A: According to the question we have to design half wave rectifier.

Q: -1 For a certain 12 V zener diode, a 10 mA change in zener current produces a 0.1 V change in zener…

A: 1 Change in zener current=10mA Change in zener voltage=0.1V

Q: (a) Draw the waveform at the output if R=100KN, Io = luA from the diode. %3D

A: According to company guidelines, only the first question will be solved for multiple questions. If…

Q: 5.) You are given a 9V battery and want to create a 5V voltage source. You have available a 3V Zener…

A: As given in the question, we have available a 3 V Zener diode with a minimum Zener current of 2 mA.

Q: Answer the questions according to the information given in the circuit below. 20kn JOU DI Vo = 0,7 V…

A: In the circuit, Two diodes are consist. Obtain output voltage waveform of the circuit in the form…

Q: Design a clamper to perform the function indicated Vị Vo +16 V Ideal diodes 20 V Vi Design -4 V -20…

Q: In a circuit that composed of a single diode that connects an AC source to a load. the diode acts as…

A: 1) We know Diodes conduct only when they are forward biased. In reverse bias diodes are treated as…

Q: tränsformer having a center-tapped secondary winding ses two silicon diodes that can be modeled to…

Q: 7. A yellow colored LED with a forward voltage drop of 2.1V is to be connected to a 5.0V stabilized…

A: Given data Voltage drop VF=2.1V Supply voltage Vs=5.0V IF≤10mA

Q: Q.1. Explains the following circuit and (a) Draw the output voltage across 1KN resistor assuming…

Q: A given monocrystalline silicon solar cell has the following specifications: Isc=5 A and Voc=0.6 V.…

A: Given that Voc=0.6VISC=5An=25 Although, All are connected in series Hence,…

Q: A silicon solar cell has a short circuit current of 90 mA and an open-circuit voltage of 0.75v under…

A: Given, Silicon solar cell has short circuit current (Isc) = 90 mA open-circuit voltage (Voc) = 0.75…

Q: B) For the circuit shown in Figure 5, sketch the output voltage V, for the input V.. D, is an ideal…

A: The diode turns forward biased when the anode voltage is greater than the cathode voltage. The ideal…

Q: 2. Design a clamper to perform the function indicated below. Silicon diodes 10 V 2.7 V -10 V -173 V

Q: olve for the value of R that will provide an output voltage of 2.4V.A he diodes available have 0.7V…

Q: Q4- For the circuits in Figure 4 a,b,c,d,e, each utilizing an ideal diode (or diodes), sketch the…

A: It is given that that CR>T, i.e capacitor takes a long time to charge or discharge. For figure…

Q: 7. A yellow colored LED with a forward voltage drop of 2.1IV is to be connected to a 5.0V stabilized…

Q: Q4. A Zener diode is used as part of a voltage regulator circuit as shown below. R 20 mA 12 V 7 mA…

A: Zener Diode-Zener diode is highly doped diode(1:105)(P+,N+). It is always fabricated with Si.…

Q: R, = 5 kn R, = 5 kn R, = 5 ka -10V -5V If the cut-in voltage of all the diodes equal to 0.7 V on…

A: Assuming all the diodes in the ON condition, then the circuit is redrawn as:

Q: 5 نقاط Q3/A: Design a clamper to perform :the function indicated below Silicon diodes 10 V 2,7 V -10…

A: DIODE: A diode is a semiconductor device that functions as a current one-way switch. It lets current…

Q: Q3/A: Design a clamper to perform the function indicated :below Silicon diodes 10 V 2.7 V -10 V…

Q: A zener regulator has an input voltage Vi of 50 V and the voltage across the load Vi is to be…

Q: a. Design such a power supply with an input Voltage ranging from 10V t 15 V, and a limiting Resistor…

A: According to guidelines we need to solve only first question. According to the question we have to…

Q: 2. Design a clamper to perform the function indicated below. Silicon diodes 10 V -10 V -173 V

A: Please refer the attached images for the complete answer..

Q: For the network below, determine the range of Vi that will maintain VL at 8V and not exceed the…

A: For the network below, determine the range of Vi that will maintain VL at 8V and not exceed the…

Q: In the circuit below, Vi = 6sin (wt) and diodes are considered ideal diodes. Describe the working…

A: Given data: Vi=6sinωt Solution: Assume that forward voltage drop across diodes that are 0.7 V.…

Q: Vi Diode is ideal draw the output waveform. +10 0.1 µF 56 k2 V. V,= 10 V Find time constant T and…

A: Diode is used in wave shaping device. Total swing in output of clamper circuit is same as total…

Q: In the follow figure, we have known E =3v u =6 sin arV Please use the ideal-diode model to analyze…

A: Need to draw output waveform

Q: èstion 23 During the analysis of diode circuits, the forward resistance will be considered if model…

A: An ideal has zero forward resistance A complete model of diode consists of forward resistance,…

Q: A 5.0V stabilized power supply is required from a 12V d.c. input which uses a stabilising resistor…

A: Part (A):- The circuit of the ZENER diode consisting load and source resistor or stabilizing…

Q: Silicon diodes 10 V 2.7 V Design -10 V -17.3 V

Q: A. When the reverse current in a particular zener diode increases from 20 mA to 30 mA, the zener…

A: We’ll answer the first question since the exact one wasn’t specified. Please submit a new question…

Q: The four diodes used in a bridge rectifier circuit have forward resistances which may be considered…

A: In a bridge rectifier two diodes operatone at a time whether in forward bias or reversebias.∴Total…

Q: Determine the state of diode for the circuit shown and find ID, VD. Assume simplified model for the…

Q: A silicon diode is in parallel with a germanium diode and is connected to a load resistor having a…

A: Voltage across the germanium diode when it is turns on is 0.3 volts and voltage across the silicon…

Q: Q3. 240V and 50HZ single-phase source is used to supply a heavily inductive load. Compare with…

A: 240V , 50Hz single phase source supplied to heavily inductive load. Compare the fully controlled…

Q: Design the circuit in the box to perform the function indicated in figure below Silicon diodes 10 V…

A: Silicon diode- Silicon diode is a diode which have both charge polarity and allow current to pass…

Q: For the following limiter consider that both zener diodes are identical with Vz =4.5V @ z =20mA and…

A: Given: For the following limiter consider that both Zener diodes are identical with VZ=4.5 VIZ=20…

Q: What is the value of the resistor that must be linked in parallel with the 6 k resistor? To limit…

Q: T

A: It is given that: VL=9 VIL=0 to 400 mAR=7Ω

Q: D2 D1 O vo O vo 1 kN 1 kQ DI D2

Q: If V1=26V ,v2=12V, R1=4.9k ohms , R2 =8.2k ohms, R3 = 1.4k ohms, and all diodes are silicon for the…

Q: The four diodes used in a bridge rectifier circuit have forward resistances which may be considered…

A: In a bridge rectifier two diodes operatone at a time whether in forward bias or reverse biasThen,…

Q: The three diodes in the circuit shown below are identical with n = 1.1. Find the value of the…

Q: . Design such a power supply with an input Voltage ranging from 10V to 15 V, and a limiting Resistor…

A: Given input voltage range, Vs=(10V to 15V) Zener voltage, Vbr=8V Rz=100Ω

Q: The circuit shown below uses 3 Zener diodes, then Vout will be equal to

Q: Find the load voltage VRL if all Zener diodes are Si with Vz = 5 V. O zero O 5.7 V O 1.4 V O 6.39 V…

Q: In a circuit that composed of a single diode that connects an AC source to a load. the diode acts as…

A: Diode only conducts in forward biase Direct. When Anode of diode is connected to postive terminal…

Concept explainers

Operational Amplifier

An operational amplifier also called op amp is an integrated circuit or analog circuit that takes input as a differential voltage and produces output as a single-ended voltage. It is an IC that can amplify weak electric signals.An op amp has one output pin and two input pins. The basic role of an opamp is to amplify the voltage difference between the two input voltages. It is also used in filtering or to perform mathematical operations or in signal conditioning.

Question

Design such a power supply with an input Voltage ranging from 10V to

15 V, and a limiting Resistor of 4.0 kΩ. Specifications of the Zener

diodes are; VBr is 8 V and RZ is 100Ω. Your task is to obtain regulated

output Voltage within the input voltage range.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

For the circuit of the figure, find vc(t)
In the circuit below, find the relationship between the output voltage ?0 and the input voltages ?1, ?2.
Please refer to the parallel-basedclipper circuit shown below for this problem.For simplicity, assume that Von = 0 for bothdiodes.(a) Plot the output vO(t) for 0 ≤ t ≤ T. Pleaseplot the vI(t) in the same graph as well.(b) Plot the voltage transfer curve (x-axis: VI& y-axis: VO)
Find the voltage, voltage gain, input and output resistances of the circuit (RS=RC=RE=2k,RB1=150k,RB2=25k,β=100, VBE=0.6V, VT=26meV)
Design the following circuit so that the operating point is at the center of the load line, keep the value of Rx. Vcc=24V, Icmax=50mA. Draw the load line.Rx=15KΩβ =86.
a)Use the DC equivalent model to find the four quiescent operating parameters. b)Develop the AC equivalent model to find Zin, Zout, and Av. Assume β = 100.
The op amp in the circuit shown shown is ideal. Calculate vo when vg equals 3 V.
(a) What are the two output currents and output resistances of the current source as shown if VEE = 12 V, βo = 125, VA = 50 V, R1 = 33 kΩ, R2 = 68 kΩ, R3 = 20 kΩ, and R4 = 100 kΩ? (b) Repeat for the circuit as shown.
How to create a circuit that has three varying input voltages and one output voltage that is equal to the average of the three? Vin = V1, V2, V3Vout = (V1 + V2 + V3) / 3 Example:V1 = 750mV, V2 = 700mV, V3 = 800mVVo = 750mV You can only use resistors and OpAmps (operational amplifiers), show circuit schematic and computations/formulas used
subject: Communication Fundamentals Modulation and Demodulation (give solve sub-parts iv and v)
4- Find the number of times the following loop is performed in 8051 microcontroller ORG 0H MOV R6, #200 BACK: MOV R5, #100 HERE: DJNZ R5, HERE DJNZ R6, BACK END
Design an amplifier circuit using OPAMP with vo= (5*v1)+(v2)+(3*v3)-(2*v4). Draw vo knowing that v1 = 1 sin (1000*pi*t), v2 = 2 sin (2000*pi*t), v3 = 3sin (3000*pi*t), v4 = 4 sin (4000*pi*t)