Determine (a) the bending stress at point H. (b) the bending stress at point K. (c) the maximum tension and the maximum compression bending stresses in the cross section. (d) the orientation B of the neutral axis relative to the +z axis. b. K H. M a (Гур.) Answers: (a) OH = MPa %3D (b) OK = MPа (c) OmaxT = MPa OmaxC = MPa

Determine (a) the bending stress at point H. (b) the bending stress at point K. (c) the maximum tension and the maximum compression bending stresses in the cross section. (d) the orientation B of the neutral axis relative to the +z axis. b. K H. M a (Гур.) Answers: (a) OH = MPa %3D (b) OK = MPа (c) OmaxT = MPa OmaxC = MPa

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

If the bending working stresses are 22.5 ksi in tension and 27 ksi in compression for the beam loaded as shown, determine a) the magnitude of the shear force at a distance of 3 ft from the left support (in terms of P) b)The magnitude of the maximum moment in the beam (in terms of P c) The largest allowable value of P
An axial force P and a bi-axial moment M are applied on the section shown below simultaneously. The moment has 2 components namely Mx and My but It does NOT have Mz component. Calculate the stresses at Points A,B,C and D. take: M= 26 kNm P= 24 kN L1= 150 L2= 70 mm
Determine the maximum shear stress in the strut if it is subjected to a shear force of V = 20 k
The frame (Figure 1) has dimensions H1 = 4 m , H2 = 3 m , and L1 = 6 m , and supports two lateral loads P1 = 10 kN and P2 = 12 kN . The area of column AE is 40 cm2 and the area of column BF is 80 cm2 . a) Use the cantilever method to determine the axial force at G. Gy = ? b) What is the horizontal reaction from the ground on the base of the column at A? Let a positive reaction be pointing to the left. Ax = ? c) What is the horizontal reaction from the ground on the base of the column at B? Let a positive reaction be pointing to the left. Bx = ?
3. The beam below is used to support a part of the overhang at the entrance of the building (a). The idealized model for beam with load is shown in (b). Assume that B is roller supported and C is simple supported. (a) Draw shear force (V-) and bending moment (M-) diagrams for the beam. Determine the position and value of maximum bending moment. (b) For the beam, assume HEA 180 for the type of cross section. Calculate the maximum normal stress and the maximum shear stress, and determine where in the cross section the normal and shear stresses are greatest. Utilize Appendix C at the end of the textbook.
For the cantilever beam with uniformly distributed load shown in Figure 2. Use (bf hf.bw, hw) for the I section from Table 2, determine the following: The maximum shear force in the beam in (kN) . The maximum bending moment in the beam in (kN.m) The area of the section in (mm?) The moment of inertia about the centroidal x axis 5The maximum shear stress at section I in (MPa) The maximum shear stress at section 2 (within the flange) in (MPa) The maximum shear stress at section 2 (within the web) in (MPa) The maximum shear stress at section 3 (at the neutral axis) in (MPa) The average shear stress on the section (MPa)
From the given simply supported beam below, determine the following: d. The moment of inertia with respect to the neutral axis. e. The maximum flexural stress and shear stress of the beam. f. The bending stress at point B and C.
The vertical load of 115 kN and horizontal load 125 kN are applied at joint F and B by using method of sections determine the force in member EG, DG and DF.
The moment acting on the cross section of the unequal-leg angle has a magnitude of 15 kN-m and is oriented as shown in the figure. All stresses are positive if tensile and negative if compressive. Assume a = 245 mm, b = 175 mm and t = 24 mm.Determine(a) the bending stress at point H.(b) the bending stress at point K.(c) the maximum tension and the maximum compression bending stresses in the cross section.(d) the orientation β of the neutral axis relative to the +z axis. (a) σH= MPa (b) σK= MPa (c) σmaxT= MPa σmaxC= MPa (d) β= °
Determine the plastic limit load P for the frame shown in Fig.
1-10. A bar of variable cross section, held on the left, is subjected to three forces, P =4 kN, P, = -2 KN, and P, = 3 kN, as shown in the figure. On two separate diagrams, plot the axial force and the axial stress along the length of the bar. Let A1, = 200 mm, A2, = 100mm², and A3, = 150 mm".
A 0.400 in. diameter solid steel shaft supports two pulleys. The shaft has a length of L = 9.9 in., and the load applied to each pulley is P = 51 lb. The bearing at A can be idealized as a pin support and the bearing at D can be idealized as a roller support. Determine the magnitude of the maximum horizontal shear stress in the shaft.