Given: • The members are a rectangular cross-section with a radius of 16 mm. • Thickness of each member is 14 mm • Diameter of the rivet used is 18 mm Determine: a. Cross-sectional area of the members b. Internal load in member AB, and indicate if 3 m 4 m tension or compression c. Internal load in member BD, and indicate if tension or compression d. Normal Stress in member AB e. Bearing stress in member BD 3m 50 KN 80 KN 4 m

Given: • The members are a rectangular cross-section with a radius of 16 mm. • Thickness of each member is 14 mm • Diameter of the rivet used is 18 mm Determine: a. Cross-sectional area of the members b. Internal load in member AB, and indicate if 3 m 4 m tension or compression c. Internal load in member BD, and indicate if tension or compression d. Normal Stress in member AB e. Bearing stress in member BD 3m 50 KN 80 KN 4 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A hollow steel [E = 30,000 ksi] tube (1) with an outside diameter of 3.00 in. and a wall thickness of 0.223 in. is fastened to a solid 1.75-in.-diameter aluminum [E = 10,000 ksi] rod. The assembly is attached to unyielding supports at the left and right ends and is loaded as shown. Assume P=18 kips, Q=13 kips, L1=4 ft, L2=6 ft, and L3=6 ft. Determine(a) the stresses in all parts of the axial structure.(b) the deflections of joints B and C.
Given: -The members are a semi circular cross section with a radius of 16mm -Thickness of each member is 14mm -Diameter of the rivet used is 18mm Determine: a. Cross sectional area of the members b. Internal load in member AB, and indicate if tension or compression c. Internal load of member BD, and indicate if tension or compression d. Normal stress in member AB e. Bearing stress in member BD
e. Calculate "P" in KN considering failure on bearing on block shear Two A36 16mm Thick Steel Plates Are Connected By Four Rivets With Fv=152 MPa As Shown. Given: Rivet Dia 20 mm x=100 mm
The angle bracket shown, 75 mm x 75 mm x 15 mm thick, is 200 mm long. It is connected to the 16 mm thick flange of the column support with 2 of 16 mm diameter bolts. The bracket is subjected to a load of 42 kN from beam A. Assume that the load is applied concentrically at the connection. 1. Determine the resulting bolt shear stress in MPa 2. Determine the resulting bolt shear stress in MPa 3. Determine the critical bolt shearing stress in MPa
Given the following allowable stresses:• 50 MPa for shear in rivets• 100 MPa for bearing between a plate and a rivet• 80 MPa for tension in the platesNOTE: Draw FBD(a) If we increase the diameter of each bar to 20 mm, determine the maximum load Pthat can be applied to the lap joint.(b) Using the value computed for maximum load P from (a) compute for the over-allfactor of safety given that the actual P= 20kN.
1. Two A36 16mm Thick Steel Plates Are Connected By Four Rivets With Fv=152 MPa As Shown. Given: Rivet DIa 20 mm x=100 mm a. Calculate "P" in KN considering tension failure on gross area b. Calculate "P" in KN considering tension failure on net area c. Calculate "P" in KN considering failure on bearing on projected area. d. Calculate "P" in KN considering failure on shear on rivets e. Calculate "P" in KN considering failure on bearing on block shear f. Calculate the maximum safe load "P" in KN
pls help! Write the complete solutions and legibly. Answer in 2 decimal places. UPVOTE WILL BE GIVEN! MECHANICS OF DEFORMABLE BODIES Let Q = 0 and T = 8 (Example: 12Q°C = 120°C). Just substitute the number in letter. Thank you! For the frame shown, a 4QQT-N load is acting on member ABD at D. If the allowable material shear stress for is 4Q MPa, determine the required diameter (rounded off to the nearest 2.5 mm) of the pins at C and D. Pin C and pin D are subjected to double shear and single shear, respectively. If the thickness of member BC is 12 mm and that of member DE is 16 mm, determine the maximum bearing stress at C.
Given: -The members are a semi circular cross section with a radius of 16mm -Thickness of each member is 14mm -Diameter of the rivet used is 18mm Determine: a. Cross sectional area of the members b. Internal load in member AB, and indicate if tension or compression c. Internal load of member BD, and indicate if tension or compression d. Normal stress in member AB e. Bearing stress in member BD (assume that the cross-section is rectangular)
The strut AB made from two bars (thickness of each bar = 0.50 in) is connected to a rectangular beam CD (b = 0.80 in x h = 7.5 in) at joint B. The beam carries a concentrated load of 2750 lb at the end joint D. (a) determine the minimum diameter of the bolt at B if the shearing stress in the bolt is not to exceed 14000 psi. (b) determine the minimum diameter of the bolt at B if the allowable bearing stress in the bar plate is 20000 psi.
A cantilever beam AB of length L = 6.5 ft supportsa trapezoidal distributed load of peak intensity q,and minimum intensity q/2, that includes the weight ofthe beam (see figure). The beam is a steel W12 X14wide-flange shape (see Table F-1(a), Appendix F).Calculate the maximum permissible load q basedupon (a) an allowable bending stress σallow =18 ksiand (b) an allowable shear stress τallow = 7.5 ksi.Note: Obtain the moment of inertia and section modulusof the beam from Table F-1(a).
The following solid aluminum bar (E = 10,000 ksi; α = 11.70E-06/F) is located between two fixed supports. Segment AB has a diameter of 3 inches and segment CB has a diameter of 2 inches. The load P is equal to 25 kip and the temperature increases by 50°F. Determine: a. The reactions at the supports. Answ: Cy = 17.938 kip (downward); Ay = 42.938 kip (upward). b. The deformation at point B. Answ: 2.693E-03 pulg. c. The stress in both segments. Anws: 5.709 ksi, 6.07 ksi.
The Channel section is used as a purlin placed on top of trusses with spacing of 4.1 m and slope 1V to 4H. The purling are supporting a total uniform load of 20.2 kN/m.Properties of Channel:Sx = 119 × 10^3 mm^3Sy = 87 × 10^3 mm^3 Compute the maximum bending stress.Use NSCP 2015Round your answer to 2 decimal places.