determine a. ID. b. VDS. c. VGG.

Q: In the network shown, what is the voltage gain?

A: It is given that:

Q: The reference node in nodal analysis is the node that will be to determine the voltage across each…

A: Consider the following circuit, The circuit has four nodes A, B, C, and D.

Q: Determine the differential equation that define the loop connected to the voltage source.

A: Resistors, inductors and capacitors form an integral part of any electrical circuit. A source,…

Q: Given the measured value of VD Determine mathematically: a) IDQ , VGSQ and VGG

A: Determine mathematically: IDQ , VGSQ and VGG  ?  Where VD  = 9V

Q: Q2, Simplify the block diagram shown below.

A:

Q: Determine and sketch the Vo for each of the network shown

A:

Q: For the circuit shown, findR * and Vs

A: To solve above problem concept required are: In series the current remain the same In parallel…

Q: find the power Supply in bhe Cir cuit in fig. 12ka 12kn

A:

Q: need the solves asap plz

A:

Q: Q3// if Vsc=25v, Isc31.33A, Find:- P.Fsc, and Xol

A: A transformer is an electrical machine which is used in AC circuit to either step up or step down…

Q: Determine the value of Vo.

A:

Q: Give an application example where AND circuit is used.

A:

Q: The reference node in nodal analysis is the node that will be to determine the voltage across each…

A: Answer : True. The given statement is true.

Q: Find the base currents of Q1 and Q2.

A: By voltage Division ruleVB= 1010+33x14    RTh= 331110 = 7.61 KΩVB = 3.25 VBy KVLVB= iR1RTh -…

Q: B) / Reduce the system shown below by using Block diagram reduction:

A:

Q: b. VGs, and Ipg Q-1) For the network of Fig. , determine: a. VG. b. VGs, and Ipg c. Ig.

A: Note :- As per guidelines we are supposed to answer only first 3_sub-parts. So I request you to post…

Q: a- Why should the licld theostat he kept in the position af minimum resistatnce?

A: At the time of starting a motor, the field rheostat is to be kept in minimum position and armature…

Q: Generate the state table and diagram of the circuit.

A: Consider the given circuit,

Q: (b) Determine V. and In for the Given Network A SKA

A: Solution 1  Considering the diodes are ideal i.e -  in forward biased                       At…

Q: V

A:

Q: Is

A: Please refer the attached images for the complete answer..

Q: In the network shown, what is the value of the output

A: BJT (bipolar junction transistor) A transistor having a three terminal made up of semiconductor…

Q: 1.For the network given below, determine VBC 2. For the network given below, determine VCE

A: We will apply KVL in the three loops to get base current and base collector voltage VBC and…

Q: C) Using your knowledge of Kirchhoff's Laws you have acquired in

A: The equivalent circuit with voltage drops polarities across each resistor based on current…

Q: Find /K/VGSQ/VRD/IDQ

A:

Q: Determine Vgg

A:

Q: Discuss two ADCs with circuit diagram and proper equations. List their pros and cons.

A: Flash type ADC The operation of Flash ADC is the fastest compared to all other ADCs. Hence, Flash…

Q: Q4 For the network of figure shown below, determine the currents Ig and Ig and the voltages VCe and…

A:

Q: What differentiate rethinking model from refine model?

A: (d) Managers have varying proclivities for participatory decision making (PPDM), thus the…

Q: Q2 (a) Based on the relationship between the line and phase value of currents and voltage, show that…

A:

Q: Q2/Reduce the system below by using the block diagram reduction:

A: YsRs=1+G1G2G3G4G6H4+G5G41-H3G1G5G41+G6H61-G3G4G5+G3G2H2+G2G3H2-1 Step (1) by combining the block of…

Q: Find a state space model' for the following electrical network. Let the output of the system

A:

Q: V.

A: The hollow cube is given below:

Q: For the circuit shown if Vs=5020°Vms.

A:

Q: Q4 For the network of figure shown below, determine the currents Ig and Ig and the voltages VCE and…

A:

Q: Determine VDQ and IDQ using load-line analysis. Also find Vo and voltage across the resistors.…

A: For the given circuit and Load analysis curve the VDQ and IDQ is calculated using Load analysis and…

Q: Generate the state table and diagram of the circuit

A: Given the sequential circuit: We need to generate the state table and state diagram of the circuit.

Q: C Q₂ Draw the circuit (A+B+C+D) using half and full a dobr which add four bits

A: Before designing a 4-bit binary adder let us know some basic rule of binary addition.   Half Adder :…

Q: (d) Determine IC and VCE for the network of Figure (b). (e) Change β to 180 and determine the new…

A: As per the policy, attempting first three subparts of the question (d)Base current can be calculated…

Q: Determine VD and VGS for the network

A: The required parameters can be calculated by using the DC analysis of the amplifier circuit.

Q: b. VGs, and Ipe Q-1) For the network of Fig. , determine: a. VG. c. IE.

A: Note :- As per guidelines we are supposed to answer only first 3_sub-parts. So I request you to post…

Q: Q2// For the following network draw ve

A:

Q: Solve for VcE -22 V 2.2 k2 82 k2 Vc IB B = 220 16 k2 0.75 k2 +12 V

A:

Q: Vz=?

A: According to the question we have to find the value of V2.

Q: - Find the base currents of Q1 and Q2.

A:

Q: Find VAF , VFB and VBD 12 V E AO O B OF 24 V `6 V `4 V D C 8 V

A:

Q: Solve for VGSQ and VDS

A: In this question,   We need to determine the voltage VGSQ and VDS  ?

Q: Q4 For the network of figure shown below, determine the currents Ig and Ig and the voltages VCE and…

A: 4. The BJT (bipolar intersection semiconductor) is developed with three doped semiconductor locales…

Q: Determine the value of the load resistance R1. shown in figure that give s maximum power…

A: To deliver maximum power load resistance should be equal to thavenins resistance of the network seen…

DC Series Motors

A DC motor is a type of electric motor which converts electric energy into mechanical energy. The forces that are produced by the magnetic field are what those common types of motors rely upon. Either electro-mechanical or electronic, all types of DC motors have some internal mechanism to change the current direction in part of the DC motors. As the DC motors could be powered from existing DC lighting power distribution systems, these motors were the first form of motors widely used. By changing the strength of the current in its field winding or by using a variable supply voltage, the speed of the DC motors can be controlled over a wide range.