PROBLEM NO. 2Determine the allowable axial load "P capacity for a rectangular columnand fixed support at both3.0 meters. If the Allowable compressive stresswith dimension of180 mm x200 mmends with length of9.56 MPa. E-7310 MPa180 mmFixed3.00 m200 mmColumn SectionFixed

Answered: Image /qna-images/answer/dcec6f25-c051-4220-bf01-5082591577a8.jpg

Determine the allowable axial load P capacity for a rectangular column 200 mm and fixed support at both 30 meters. If the Alowable compressive stress with dimension of 180 mm x ends with length of 9.56 MPa.E- 7310 MPa is 180 mm Fixed 3.00 m 200 mm Column Section Fixed

Determine the allowable axial load P capacity for a rectangular column 200 mm and fixed support at both 30 meters. If the Alowable compressive stress with dimension of 180 mm x ends with length of 9.56 MPa.E- 7310 MPa is 180 mm Fixed 3.00 m 200 mm Column Section Fixed

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 3. This tension member contains 20mm diameter bolt holes. What should be the value of s so that the ...

A: “Since you have asked multiple question, we will solve the first question for you. If you want any s...

Q: A 40 cm diameter pipe is carrying discharge in turbulent regime. The pipe's interior surface irregul...

Q: You are asked to design a horizontal curve for a two-lane oad. The road has 3.6- m lanes. Due to exp...

Q: The floor frame shown carries a (superimposed) service dead load of 2.2 kPa. Slab S1 is 110 mm thick...

A: We have to determine the value of dead load carried by the different beams and girders also compute ...

Q: Determine the magnitude Fand direction 8 (measured clockwise from the positive y-axis which is downw...

Q: A foundation carries uniform loads as shown. Determine the value of w (in kN/m). 70 kNm W. 4m 2m

A: We are required to find the value of w

Q: Question 41 of 46 In raising the 52-m pole from the position shown, the tension Tin the cable must s...

Q: A commercial airliner with four jet engines, each producing 64 kN of forward thrust, is in a steady,...

Q: Degree of curve, DA = 2° 00' 00", STA @ BC = 21+33.04 (feet) Determine the radius of the curve (feet...

A: Given : circular curve with degree of curve = 2 degrees STA@BC = 21+33.04 (feet)

Q: A four storeyed building has an elevation shown in Fig. 20.10 and is located in seismic zone IV. Det...

Q: An experimental device imparts a force of magnitude F = 67 lb to the front edge of the rim at A to s...

Q: Situation 1| Simply Supported Beam ABCDE below carries multiple loads as shown. A built-up section m...

Q: Compute the volume change of a solid copper cube, 40 mm on each edge, when subjected to a pressure o...

A: We have to determine the value of volume change of a solid copper cube 40 mm on each edge when subje...

Q: An equal-tangent vertical curve with an entry grade of +1.0% and a final grade of -2.0% was designed...

A: Given, G1 = 1% G2 = -2% V = 110 km/hr

Q: A foundation carries uniform loads as shown. Determine the value of w (in kN/m). 70 kNlm 70 bNm fom ...

A: Given information in question Footing / Foundation UDL Span dimensions To find out Value of W

Q: To check the radius of a railroad curve, the effect of a 40-N weight is observed to be 41.400N on a ...

A: Given, Speed of car = 64 kmph Measured weight = 41.4 N Actual weight = 40 N

Q: Determine the factor of safety against overturning.

Q: From the given technical description shown. Lines Bearings Distances (m) AB N 32°27' E 110.8 BC ? 83...

Q: Compute the acceleration of body B and the tension in the cord attached to it. 300 lb 4-0.20 200 lb ...

A: Given: The coefficient of friction is 0.20. Consider the figure,

Q: What document is required for facilities before they discharge treated wastewater into bodies of wat...

Q: Pick up the correct statements about Free Vibration of Undamped SDOF System: Motions taking place wi...

Q: Prob. 1: From the following design information for a circular horizontal curve; Degree of curve, DA ...

A: Given Degree of curve = 2*00'00" STA@BC = 21+33.04 ft To find - The radius of curve and the station...

Q: (1) The three-bar truss ABC shown in the figure is constructed of steel pipes having cross- sectiona...

A: “Since you have posted a question with multiple sub-parts, we will solve first three sub-parts for y...

Q: If the longitudinal main reinforcement in beam used is D-16 mm, the size of stirrup should be

Q: Calculating settlement. Worked example ge landfill is planned on 10 m of normally consoli- i clays w...

A: Ysat = 18Kn/m3 YW = 10Kn/m3 H0 = 10 m Coefficient of Consolidation CC = 0.15 Porosity = 0.5 e...

Q: For a colony of 10000 persons having sewage flow rate of 200 1/capita/day, BOD of applied sewage is ...

Q: solve the whole truss find equilibrium find R1 ,r2, FAB,FAI,FBC,FBI,FCI, FCH,FCD, FIH, FHD,F...

Q: The connection shows a PL10X200 loaded in tension and welded to a 10mm gusset plate. Calculate the f...

Q: Determine the location of the horizontal neutral axis of the section (in mm) with respect to the bot...

Q: An airport is to be constructed at a site 190m above mean sea level and on a level ground. The runwa...

Q: If a two dimensional flow field is defined as V = xi - - yj then The flow is occurring along a strai...

Q: Determine the moment capacity of the section, kN-m, if fbcap≤300 MPa.

Q: Structural Theory

Q: Find moment at O, given the figure below. 50 N 2 m 5 m

Q: fy = 415 MPa n = 9 Tension reinforcement: 2 – 25mmø RSB 1.4 Pmin fy Pmax = 0.75pp 0.85f:B, (600) Pb ...

A: Given : b = 200 mm D = 400 mm, d = 337.50 mm fc = 21 MPa fy = 415 MPa

Q: Find The value of Work done if fosice applied is 6 N cwhich by 4 elis place "the obyect m.

A: Introduction : Work done is a parameter which depends on force applied and the value of distance cov...

Q: Calculate for the following member forces of the frame shown below using Portal Metho a. Shear at co...

Q: What is the most common cause of noise in internal detectors

Q: A В

Q: Calculate the moment (positive if countercloewise, negative if clockwise) of the 290-N force on the ...

Q: At station 5 +100 of a portion of a highway stretch has an area of 100 m2 in cut while that of stati...

Q: Determine

Q: A right circular cone with radius 'r' is inscribed in a sphere with radius 'R. If it is known that, ...

Q: Simply Supported Beam ABCDE below carries multiple loads as shown. A built-up section made from a T-...

Q: P1. Two blocks A and B are released from rest at 30 degree incline when they are 50 ft. apart. The c...

Q: 7. Calculate the Moment of force acting on the bracket about point O. 400 N 100 mm 60 120 mm 60 mm

A: To find moment about point O

Q: 16.3

Q: The alkalinity of a water sample is 120 mg/1 as CaCO3. pH of the water sample is found to be 9. Conc...

Q: An 8-meter long horizontal beam is supported to the left end by a fixed support and supported to the...

A: To find the maximum bending moment in the beam

Q: Ql-1) See Figure 1, classify each of the structures as statically determinate, statically indetermin...

Question

PROBLEM NO. 2
Determine the allowable axial load "P capacity for a rectangular column
and fixed support at both
3.0 meters. If the Allowable compressive stress
with dimension of
180 mm x
200 mm
ends with length of
9.56 MPa. E-
7310 MPa
180 mm
Fixed
3.00 m
200 mm
Column Section
Fixed

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

An eight meter simply supported beam carries a superimposed dead load of 6kN/m and aservice live load of 15kN/m. The beam has a width and total depth of 400mm and 550mm respectively.It is reinforced with five diameter 25mm bars and 10mm stirrups. Material properties are fc'=27.60MPaand fy=421.60MPa. 1. Using the detailed calculation of Vc, required spacing of stirrups at 1.20m from the support using the NSCP 2015 provisions.
A rectangular, tied column 480 mm wide along x-axis and 540 mm wide along y-axis is reinforced with 4 25-mm-diameter vertical bars with fy = 420 MPa enclosed in 10-mm-dia. ties. Using f'c = 21 MPa, calculate the nominal axial strength at balanced condition in kN with bending about the x axis. Write your answer with 2 decimal places only.
6 Calculate the nominal shear strength (kN) of 4-legged stirrups 12-mm-diameter, spaced at 280 mm on centers for a beam with effective depth of 417 mm. Use yield strength of stirrups fy = 275 MPa.
ACI Code Table 9.7.6.2.2 sets the maximum spacing of vertical stirrups of d/2. Explain why?
Calculate the required steel area for a reinforced concrete T-beam with an effective flange width of 1200 mm and a slab thickness of 100 mm. The beam is to carry an ultimate moment of 1300 kN-m. The width of the web is 300 mm and the effective depth is 550 mm. Assume f’c = 28 MPa and fy = 400 MPa * a. 7772 mm² b. 8256 mm² c. 7932 mm² d. 7232 mm²
If the resultant force acting on the bracket isrequired to be a minimum, determine the magnitudes of F1and the resultant force. Set Φ = 30°.
A circular column carries an axial concentric dead load of 1530kN and a live load of 1420kN. Assume 12mm diameter of spirals, fc’=30MPa and fy=425MPa. If the allowed steel ratio is 0.04, Determine the diameter of the column in the nearest tens, mm. Determine the number of diameter 28mm longitudinal reinforcements. Which of the following gives the pitch of the spiral?
2. A 50- m steel tape weighs 0.04 kg/m and is supported at its end points andat the 9-m and 30- m marks. If a pull of 6kg is applied, determine thefollowing:a) correction due to sag between the 0-m and 9- m marks, 9-m and 30-mmarks, and the 30- m and 50- m marks.b) correction due to sag for one tape lengthc) correct distance between the ends of the tape.
36 -Loading status in figure q= 4 kN ⁄ m, P = 48 kN in the bar dimensions L= 2 m and e= 0.5 m. The cross-sectional effects at point E will be calculated. A is fixed, B is sliding joint bearing. Accordingly, By=? a) 0B) 48C) 24D) NoneE) 14
For questions 2A and 2B, refer to the load and shear diagrams below. 2A. What is the slope of the shear diagram of the line from B to C?A.15 KN/mB.16 KN/mC.24.46 KNmD.11.26 KNmThe change in moment [KNm] of the diagram above from point A to the concentrated load is nearest toA.98B.99C.100D.101
A rectangular beam is 15 in. wide and 30 in. deep. For f c′ = 4000 psi and fyt = 60,000 psi, determine the required spacing of No. 4 (No. 13) closed stirrups for a factored shear of 80 kips and factored torsional moment of 50 ft-kips. The stirrup centroid is located 1.75 in. from each concrete face. The effective depth is 26.5 in.
please help! upvote will be given. NO LONG EXPLANATION NEEDED STRENGTH OF MATERIALS Draw the shear-force and bending-moment diagrams for the simply supported beam shown. Determine the shear force 3.5 m to the right of point A if W = 9.9 kN/m, T = 14.75 kNm, m = 11.1 m, and n = 5.9 m. Round off the final answer to four decimal places.