Determine the Available colum strength for Colum AB in the Frame, Fy= 50ksi Colum above or below assume are the same Size as AB. only in plane behavior is Considered A) Assume elastic Behaviar Answer (Indowed 6,27 K, LRFD, 420 K ASD) B) Assume melastic Behavior PD= 140K, PL = 260k Answer (629k, LRFD, 420K ASD)

Determine the Available colum strength for Colum AB in the Frame, Fy= 50ksi Colum above or below assume are the same Size as AB. only in plane behavior is Considered A) Assume elastic Behaviar Answer (Indowed 6,27 K, LRFD, 420 K ASD) B) Assume melastic Behavior PD= 140K, PL = 260k Answer (629k, LRFD, 420K ASD)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

rectanqular seetion with width bz250 and depth h= 500mm is to carcry a A m %3D design bending moment M= 260KN•M, The conerete is of greade e30 and the tensile steel is of HRB400. The tension reinforzce. ment A, is requined.
2- A steel pod is stretek between two rigid walls ard carries a tensile Coad 4GO0ON at c f the allowatle Stress is not to excred 130 MPa at -4C, what is the minimum the nd? diameter f ard E= J00 GPa. Figure: ST L
Maxinnun allowable stress for steel - 140 MPa Maxinnum allowable stress for ahuminum = 90 MPa Maxinnun allowable stress for brouze - 100 MPa Required: Maximun safe value of axial load P Aluminum A 400 mm Bronze A= 200 mm Steel A= 500 mm 2P 4P 2.5 m 2.0 m 1.5m
7 30 Enercise:- diameter of 12mm A cylindrical rod 100 mm long with is subjected to a 30000 N. Assuming that the tensile load of deformation is entirely elastic and allowable elevation in pligmeter is allowable reduction in dligmeter is 0.015mm. choose amory only meeting requirent U (Poiss ons vahu) 0.33 below Material Aluminium alloy Bronze Titanium allow manimum 0.3 mm while manimum E (GPa) 70 100 110 0.34 3
4 A flanged bolt coupling has ten 12-mm di ameter steel bolts on 500 mm diameter b olt circle and six 16 mm diameter aluminu m bolts on 300 mm diameter bolt circle. T he maximum shear stresses of the materi als are 60 MPa in steel and 40 MPa in al uminum. Use G = 80 GPa for steel and 3 0 GPa for aluminum. What is the maximu m required shear strength of each alumin um bolt to determine the maximum torqu e that can be applied to the system? Dra wing not included in this problem.
2-A teel ptd is stretek between fwo rigid walls ard carries a tensile load f GO0ON at C f the alowatle Stress is not to excred 130 MPa at -4°C, what is the minimum diameter f the nod? as ard t= a00 GPa. figure: ST L
7 Enercise:- 30 long with is subjected to a Assuming deformation is entirely elastic and manimum allowable elongation tensile 30000y that the is 0.3 mm while manimum. allowable reduction in, digmeter is 0.015mm. choose amory below only. candidate meeting requirent E (GPa) A cylindrical rod 100 mm diameter of 12 mm load of 30000 N. Aluminium alloy Bronze Titanium allow 70 100 110 U(Poiss ons vahi) 0.33 0.34 0.3
Structure w:- Analyze by the Con Sistend defor madion_method defor mation method EXH- the bean shown and then D raw S-F D and B-MD EI Canstamnt- sol. .A. 3+0 i Stad Indeteminade 3m to the 1st degree- one redundant) (M)E (2) |(* +here S priman det- Aio choose RB () redundant. as. 84 36 Str. nd3)=Rc(10) ieRc=367 Fjeo1 RA =84 KN1 mi * SMA= 0,4 Ix6=RCAlo RA=0.4 Sec. orig. timits. AD 0--3 84X AB 36 84x-12olk-) oi4 ¥3+X) 0 384(x-3)-120(x) 0-47 CB 36X
2- A 2m COPPER BAR SUBJECTEO TO A TENSILE IS SUSPENDED FROM A LOAD IBO KN SUPPORTED BY TWO IDENTICAL PIN THAT S pOSIS AS SHON OF THE LOWER AFPLIED TENSILE POSTS SUPPORT THE STEEL DETERMINE THE TOTAL DEFORMATION END OF THE LOAD HINT: NOTE THAT THE STEEL PIN WHERE THE COFPER BAR IS ATTACHED. COPPER BAR DUE TO STEEL POST L=0.5m A= 4500mm E- 200GPA COPFER BAR L- am A= 4800 Mn E- l20 GPa 180KN
(2) 4 0 5 211 5 4 #9 4 "1 16 #3" ft-k fé = 3 ksi, M = 90 NWC. The section is cracked. Computer the bending stresses in the beam by using transformed-area metho
Q1 Delermine the design (ultimate) bending mement for the beam sections showen belowi- 300 mm AG0 mn 330 530 4 bars A es 70 (a) fy s20 Mla - 34 Mla SI0 mm fe'= 28 MAA An 820 mn Ans: prh= 448ma) (Ans: Sectien has
Two polymer bars are connected to a rigid plate at B, as shown. Bar (1) has a cross-sectional area of 1.71 in and an elastic modulus of 2050 ksi. Bar (2) has a cross-sectional area of 1.019 in? and an elastic modulus of 3910 ksi. Assume L-20 in. Lyn47 in. Q-6 kips. P-3.6 kips, and R-13.2 kips. Determine the horizontal deflection of end Crelative to end A. (1) (2) Answer: UCIA - in.