Determine the average normal stress at section a-a and the average shear stress at section b-b in member AB. The cross-section is square, 0.45 in. on each side. Draw free-body diagram. Determine the average normal stress atsection a-a and the average shear stress atsection b-b in member AB. The cross-section is square, 0.45 in. on each side.150 lb/ftC4 ft60°aab

Given:- Cross section side of square = 0.45 inch

Answered: Determine the average normal stress at…

Determine the average normal stress at section a-a and the average shear stress at section b-b in member AB. The cross- section is square, 0.45 in. on each side. 150 lb/ft C 4 ft 60° a

Principles of Foundation Engineering (MindTap Course List)

8th Edition

ISBN:9781305081550

Author:Braja M. Das

Publisher:Braja M. Das

Chapter6: Vertical Stress Increase In Soil

Section: Chapter Questions

Problem 6.4P: Refer to Figure P6.4. A strip load of q = 900 lb/ft2 is applied over a width B = 36 ft. Determine...

See similar textbooks

Related questions

Q: Determine the maximum torsional shear stress in the 40-mm-diameter shaft. 150 mm 10 kN B 4 kN

A: torsion at B :TB=(6-2)×150×10-3×10-3=600N-mTA=(10-4)×100×10-3×10-3=600N-m

Q: The effective stress (kPa) at C is A 0.5 m y 16.0 kN/m? Ksat = 16.5 kN/m D. 0.5 m %3D Ysat = 20…

Q: Refer to Figure P6.3. Determine the vertical stress increase Δσ at point A with the values q1 = 90…

A: Given: Line load 1, q1 = 90 kN/m Line load 2, q2 = 325 kN/m Distance between line loads, x1 = 4 m…

Q: If the concentrated load, P = 5 kN, the resultant stress (in MPa, in integer) experienced at point…

A: given- a prestressing beam with a prestressing force acting at a distance of 100mm from neutral…

Q: Q2: For the beam of section shown, the bending moment =12.5 kN.m and shear force = 14.4 kN determine…

Q: 5.12-2 A solid circular pole is subjected to linearly varying distributed force with maximum…

A: The maximum allowable stress is σallow=150 MPa. The length of the pole is L=3 m. The linearly…

Q: Determine the maximum shearing stress (MPa) in a solid shaft of 60-mm diameter as it transmits 94 kW…

Q: 3. Determine the principal stresses . 02 and the principal direction a, from the following stress…

Q: A B C D 40 kN.m 60 kN•m E OK 30 kN-m 50 kN-m

Q: average

Q: The bar has a 140 mm by 20 mm rectangular cross section. If P = 190 kN, determine the force…

A: Appreciate if there is detailed work with explanation and finds you helpful for ease of…

Q: Calculate the average normal stress and the average shear stress on a plane passing horizontally…

Q: Determine the average normal stress and average shear stress at point C in the beam. The…

Q: The simply supported beam AB as shown in Figure Q3(a) has a uniform load of intensity, w=15 kN/m…

Q: Determine the maximum total stress in the cross section for the below beam. 50 kN 3 60 kN D B 2 m 2…

A: Calculate support reaction at support A and D:

Q: A rectangular channel 2.5 m wide carries water at a depth of 1.2 m. The bed slope of the channel is…

A: Given data,Width of channel =2.5 mdepth =1.2 mbed slope =0.0036to find average shear stress on the…

Q: Determine the average normal stress at section a-a and the average shear stress at section b-b in…

Q: The major principal stress (kPa) on the soil element is (anti-clockwise shear +ve) 100 kPa 50 kPa…

Q: A 24-mm-diameter solid shaft is subjected to an axial force of P = 4700 N, a horizontal shear force…

Q: Determine the vertical shear stress 1.5" below the top, 3" above the bottom and the maximum on the…

Q: Q1/ The below cross section is for a beam has a maximum applied moment of 50 kN.m and a maximum…

Q: The hollow circular shaft having 120 mm outer diameter and 80 mm inner diameter. It is subjected to…

A: Torsion means twisting of a structural member when it is loaded by a couple that produces rotation…

Q: mm. (a) Determine the magnitude of the horizontal sl =D310 N. (b) If the allowable shear stress for…

A: Given:- D=35mm d=33m a=86mm t=8mm To find:- a)maximum shear b)V

Q: The uniform beam is supported by two rods AB and CD that have cross-sectional areas of 12 mm? and 18…

A: Drawing free body diagram and using equilibrium equations

Q: 1. A solid aluminum alloy disk with uniform thickness has an allowable speed of wall = 40,000 RPM, a…

A: Introduction- The neutral axis has the most shear stress. The shear stress decreases as the point…

Q: In the beam is gi In the ngure, a) Calculate all the internal forces in the most critical section.…

Q: Q2: Find the increase of the vertical total stress, and total stress at point Z. 02 N/m Q1…

A: Given data- Q1=2100 KN/m/meter Q2=10500 KN/m z=3 Dry unit weight of soil = 16.32 KN/m3

Q: If M=50 kN-m, what is the bending stress at the center of the upper hollow circle about the z-axis?…

Q: Determine the maximum shear stress in the T-beam at section C. Show the result on a volume element…

A: Solution:

Q: SECTION: 300 mm 10 KN m 800 mm B 15m P= 300 KN e = 250 mm A. Calculate the stress at the top located…

Q: A. Determine the maximum bearing stress in MPa if P = 115 kN. B. Determine the maximum shear stress…

A: The given figure is shown below:

Q: 4. Determine the maximum flexural stress; 5. Determine the maximum flexural stress at a section 2.5m…

Q: Determine the lateral earth pressure force on the wall (6.0 m height shown in the figure. Draw the…

Q: For the overhang beam shown, determine the shearing stress (a) at the neutral axis and (b) at the…

A: Left support is considered as A and Right support considered as B

Q: S. A rectangular beam 10 cm wide, is subjected to a maximum shear force of 50,000 N, the…

Q: 1. The shaft is subjected to the axial force of 40 kN. Determine a. the average bearing stress…

Q: . At a point, the major principal stress 66 KPa (c) and the minor principal stress is 34 KPa (T). a)…

Q: The beam is supported by two rods AB and CD that have cross-sectional areas of 12 mm² and 8 mm²,…

Q: SITUATION 11. A 12 mm thick steel tank has a diameter of 3m and is 6m high. 31. When the tank is…

A: Given:- The thickness of the steel tank = 12 mm = 0.012 m The diameter of the steel tank = 3 m The…

Q: The simple beam with a height of 200mm, a width of 100mm and a length of 4m loaded as shown. Do the…

Q: Q1/ Draw the distribution of the effective stress for section A-A in the following soil profile: A…

Q: 2. A 3.0 x 1.5m sign is supported by a hollow circular column, which has a 100mm outside diameter…

Q: inclined at 30° to the known directions of the respectively. E = 2.1 x 10$ N/mm? and Poisson's In a…

Q: fM = 50 kN-m, what is the maximum bending stress about the AB-axis? (in MPa) Radius of hole 3 R 2…

Q: A rectangular channel 2.5 m wide carries water at a depth of 1.2 m. The bed slope of the channel is…

Q: 2. A sign with dimensions of 2.0 m x 1.2 m is supported by a hollow circular pole having an outer…

Q: The channel section shown in Figure P9.65 is subjected to a vertical shear force of V = 7 kips.…

Q: 1.2 The cross-sectional area of bar ABCD is 600 mm². Determine the maximum normal stress in the bar.…

A: Given:- The cross-sectional area of the bar ABCD = 600 mm2 To determine:- The maximum normal stress…

Q: SITUATION 1| The system below is consisting of two solid circular cross-section bars AB and BC,…

Question

Determine the average normal stress at section a-a and the average shear stress at section b-b in member AB. The cross-section is square, 0.45 in. on each side. Draw free-body diagram.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Similar questions

The bar has a 140 mm by 20 mm rectangular cross section. If P = 190 kN, determine the force components perpendicular (N) and parallel (V) to a-a, the inclined surface area, and the normal and shear stress magnitudes acting on surface a-a.
P = 15 kN Determine the normal and shearing stress at point a, b, and c.
The cantilever beam is subjected to a concentrated load of P=20kips. The cross-sectional dimensions of the rectangular tube shapre are b=5.2in , d=8.10in , and t=0.400in. Determine:a) The magnitude of the maximum horizontal shear stress in the rectangular tube shape. Answer in ksi, rounded-off to 2 decimal places.b) The magnitude of the shear stress at point K, which is loacted to the left of the vertical centroidal axis zK=1.1in. Answer in ksi, rounded off to 2 decimal places.
P = 49 kips Determine the normal and shearing stress at point a, b, and c
1.) Draw the internal stress and strain diagram of beam considering that the depth of the stress block is greater than the thickness of the flange. f’c =30 MPa, fy=400 MPa and is subjected to a positive bending Mu=140KN-m.
If d = 450 mm, determine the absolute maximum bending stress in the overhang beam.
A 0.2 m diameter shaft is supported by a smooth journal bearing at E and a smooth thrust bearing at F. Determine the maximum shear stress developed in segment BC of the shaft. 43.33 MPa 35.01 MPa 13.12 MPa 22.11 MPa
The solid circular shaft is subjected to an internal torque of T= 6.0 kN.m. Determine the shear stress developed at point A and B
a horizontal single force P of 150 lb magnitude is applied to the end D of lever ABD. 1. what is the normal and shear stresses at point H having sides parallel to the x and y axes? 2. determine the principal planes and pricipal stress at the point H
If M=50 kN-m, what is the bending stress at the center of the upper hollow circle about the z-axis? (in MPa).
The figure which is in equilibrium under the forces P and F = 42 kN inclined at θ= 48o, is supported by a pin at D. Determine the shear stress in the pin if it is 21-mm-diameter.
A. Determine the maximum bearing stress in MPa if P = 115 kN. B. Determine the maximum shear stress in MPa if P = 115kN. C. Determine the maximum tensile stress in MPa if P = 11 kN.