Determine the capacitor size in micro farad necessary to increase the power factor by 20% if P1 and P2 loads are connected in parallel; Repeat if the load is only P1 load connected i Determine the capacitor necessary to increase the power factor by 20% if the loads are: P1= 100KW, pf=0.707 P2= 50 kW, pf=0.600 VL= 480 volts rms RL=0.1 ohm f=60 Hz

Determine the capacitor size in micro farad necessary to increase the power factor by 20% if P1 and P2 loads are connected in parallel; Repeat if the load is only P1 load connected i Determine the capacitor necessary to increase the power factor by 20% if the loads are: P1= 100KW, pf=0.707 P2= 50 kW, pf=0.600 VL= 480 volts rms RL=0.1 ohm f=60 Hz

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.7P: Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor,...

See similar textbooks

Similar questions

1. A motor load consists of a resistance of 6 Ohms in series with an inductance of 12 mH. Assume 120Vac, 60 Hz supply. a. What is the complex impedance of the load? b. What is the ac current through this load? c. What is theta, the angle between voltage and current through this load? d. What is the power factor? e. What capacitance should be added in parallel with this load to correct the power factor to 1? f. What is the current from the supply when the power factor is corrected?
AC electrical circuit is below: (refer picture below) a. Determine the current flowing in the load. b. If it is desired that the system power factor be 0.9. With system frequency = 50 Hz. Determine how large the capacitor is must be installed? Which one is correct? A/B/others answer A. C = 7.7015 mF B. C = 35.243 µF c. Please Draw all the phasor. Please give complete, details, and correct answer. Please do step by step, draw the phasor Please using handwriting (not typing ). THANK YOU, I WILL GIVE MANY THUMBS UP.
Between the terminals a and b in the figure, there is a load formed by connecting the resistor R0 and inductance L0 in series. The amplitude of the voltage Vs (t) is √2 150 volt phase angle Qs = 0 degree period T = 200π microseconds. Since R = 300ohm and C = 1 microfarad A) If the load phase angle QL = 30 degrees, find the values of R0 and L0 that enable the load to draw the maximum average power from the circuit. =? B) Calculate the average power on the load. =?
In the circuit shown in the figure, there is a load between the terminals a and b, consisting of the series connection of the resistor R0 and the inductance L0. The amplitude of the voltage Vs (t) is two root hundred and fifty phase angle Qs = zero degree period T = 200 PI microseconds. Since R = 300 ohms C = 1 nano F. a) Find the values of R0 and L0 that enable the load to draw maximum average power from the circuit b) Calculate the complex power on the load.
A factory has a large induction heater operating at 1000 V, 50Hz. The current flowing intothe heater is 12.33 A RMS and the true power is 10 kW b) Calculate the reactive power, apparent power and the power factor (PF) for this load.c) If the PF is lower than 0.9, explain the problem from an electrical perspective thencalculate how this load could be balanced practically.d) Draw a diagram to illustrate where the capacitor needs to be placed and what hashappened to the reactive current that was originally flowing from the inductive load backto the supplier? What are the specifications for this capacitor? What would such acapacitor cost? Who could supply this type of component?
(a) Calculate the equivalent impedance of the circuit given below, if the source voltage is v(t) = 60cos1000t (b) Calculate the source current flowing in the circuit (c) Draw the phasor diagram of the current and input voltage
A residential four-wire system supplies power at220 V rms to the following single-phase appliances:On the first phase, there are ten 75-W bulbs. On thesecond phase, there is a 750-W vacuum cleaner with apower factor of 0.87. On the third phase, there are ten40-W fluorescent lamps with power factor of 0.64.Finda. The current in the netural wire.b. The real, reactive, and apparent power for eachphase.
The variable resistor Ro in the circuit shown is adjusted until maximum average power is delivered to Ro.1. a) What is the value of Ro in ohms?2. b) Calculate the average power delivered to Ro.3. c) If Ro is replaced with a variable impedance Zo, what is themaximum average power that can be delivered to Zo?4. d) In (c), what percentage of the circuit’s developed power isdelivered to the load Zo?
Kindly answer letters d, e, f, g A 25 ohm resistor connected in series with a coil of 50 ohm resistance and 150 mH inductance. The combination is connected across the 220 V source. Calculate for the (a) power factor; (b) impedance; (c) true power; (d) graph the impedance triangle; (e) graph the power triangle; (f) show via phasor diagram the behavior of the current and voltage; (g) plot the sine wave equation of the current and voltage.
A residential four-wire system supplies power at 220 V rms to the following single-phase appliances: On the first phase, there are ten 60-W bulbs. On the second phase, there is a 1-kW vacuum cleaner with a power factor of 0.9. On the third phase, there are ten 23-W compact fluorescent lamps with power factor of 0.61. Find a. The current in the neutral wire. b. The real, reactive, and apparent power for each phase.
The variable load resistor RL in the circuit shown is adjusted for maximum average power transfer to RL. 1. a) Find the maximum average power.2. b) What percentage of the average power developed by the idealvoltage source is delivered to RL when RL is absorbing maximumaverage power?3. c) Test your solution by showing that the power developed by theideal voltage source equals the power dissipated in the circuit.
An industrial installation has a power factor of 0.85 in backward. The demand is 150 KVA, and the operating voltage is 4800 V at 60 Hz. What should be done to bring the power factor to 0.95 in lagging? Indicate what you would connect and with what three-phase power. If the connection of the element to be added is in delta, indicate its reactance and the value of its capacitance or inductance. capacitance or inductance.