Determine the deflection 8g at the free end of a cantilever beam AB with a uniform load of intensity q=4,6 kN/m acting over the middle of the length and a point load. The lenghth of beam is equal to L=4 m. The beam has flexural rigidity El-4852167 Nm². Note that upward deflection is positive. P=qL/6 A 9 L 3 B 4

Determine the deflection 8g at the free end of a cantilever beam AB with a uniform load of intensity q=4,6 kN/m acting over the middle of the length and a point load. The lenghth of beam is equal to L=4 m. The beam has flexural rigidity El-4852167 Nm². Note that upward deflection is positive. P=qL/6 A 9 L 3 B 4

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Analyze the propped beam loaded as shown below: use either double integration or area moment method. 1.Determine the reaction at the roller support. Ans.: RA = kN 2. Determine the deflection at midspan of the beam. Ans.: kN.m3 3. Determine the slope at 2m from the roller support. Ans.: kN.m2 4. Determine the moment reaction at the fixed support. Ans.: MA = kN.m
If Mz = 545 kip-ft, find the magnitude of the bending stress at a point H. For the beam cross section, assume a = 10 in. b = 14 in. d = 35 in. r = 5 in. The centroid of the cross section is located 16.07 in. below the uppermost surface of the beam. The moment of inertia about the z axis is 44269 in.4.
For the truss in Figure P8.3, compute the horizon-tal and vertical components of the displacement of jointC. The area of all bars = 2500 mm2, and E = 200 GPa.
Vertical Forces P & F in the figure produces a resultant of 500KN and a counter clockwise couple C of 250 KN-m. Find the magnitude of force P. a.) 1187.5 KN b.) -1687.5 KN c.) -1187.5 KN d.) None of the Above e.) 1687.5 KN
A simply supported beam of span 29.52 ft. carries two-point loads 210 KN and 125 KN at 6.56 ft. and 19.68 ft. from left support. The self-weight of the beam is 26 KN/m. Determine the maximum slope and deflection at the centre. EI is a constant.
A rectangular beam is supported at both ends. It carries two concentrated load of 110kN, a clockwise moment of 110kN-m, and a uniformly distributed load "w". The modulus of elasticity of the beam is 60GPa. Solve the following if the reaction at point B is 328.90256410256kN, upward. BEAM DIMENSION: Width = 190mm , Height = 390mm NOTE: b = 4.8m ; Determine the deflection at midspan
From the beam shown. Let P = 30 kN, Q = 2 kN/m, L =6m. Determine the following;a. Reaction at A.b. Constant C1.c. Slope at L/3.d. Deflection at L/3.
From the beam shown. Let P = 40 kN, Q = 4 kN/m, L =8m. Determine: 1. Reaction at A. 2. Constant C1. 3. Slope at L/3. 4. Deflection at L/3.
Determine the location of the maximum deflection on the beam, the value of this maximum deflection, and the slope and deflection 4m to the right of R1. EI is constant, and R1 and R2 represent reactions of a simply supported beam.
Compute the value of EIy at 2.5 m from the left support.
The block A and the wedge B weighs 100 kN and 40 kN, respectively. The coefficient of fritction for all contacting surfaces is µ = 0.268. Determine the following: a. What value of P in kN would be required to push to the right the wedge under the block? b. What value of P in kN would be required to pull to the left the wedge under the block? Assume the block A is stll in contact with the wall just as motion starts.
The left half of the simply supported beam carries a uniformly distributed load of internsity 600N/m. A.Compute the value of ??? at midspan. B.If E= 10GPa, determine the smallest value of I that limits the midspan displacement to 1/360th of the span.