determine the diameter     of the rod C if the allowable stress 86.60 MPa.         Neglect the weight of the bar AB.

Q: Determine the normal stress in a ball, which has an outside diameter of 180 mm and a wall thickness…

A: Given data in question  Pressure  Outside diameter  Thickness To find out  Normal stress

Q: Using the principles of Mohr's Circles for the soil element shown in Figure. Determine the…

A: Radius of the circleR=(σx-σy2)2+τxy2R=(-9.6-2.42)2+-32R=6.708 kNm2σAVG=σx+σy2=-9.6+2.42σAVG=-3.6kNm2…

Q: For the given plane stress state '=120 MPa, ' c= 100 MPa and °c=150 MРа, σύ. . Calculate the…

A: Given: σb=120 MPaτc=100 MPaσa=150 MPa

Q: 18- Pressure applied equally on a rock: A. differential pressure B. directed pressure C.…

A: Confining Pressure applied equally on a rock.

Q: Determine the hoop stress developed in a thin wall cylindrical pressure vessel of diameter 1.5 m and…

A: Given data : Diameter (d)=1.5 mwall thickness (t)=20 mmInternal pressure (p)=500 kPa

Q: the vertical stress oz for each of the following cases:

A: There are two methods to calculate stress vertically at the ground surface Boussinesq method…

Q: 2. A water tank rests on soil. The vertical stress due to the tank is 60kPa resulting to an outward…

A:

Q: Determine the normal stress in a ball, which has an outside diameter of 165 mm and a wall thickness…

A:

Q: The cross-sectional area shown is subjected to V = 600 kN and M -1000 kN-m. What is the maximum…

A: The flexural stress is given by: σ=MyI Where, M = Moment y = Depth of neutral axis I = Moment of…

Q: Determine the normal stress in a ball, which has an outside diameter of 195 mm and a wall thickness…

A: step 1-

Q: refer to the figure due to application of line load q1 and q2 . the vertical stress increase at…

A: Given: The vertical stress is 42 kN/m2. Consider the figure,

Q: A rectangular concrete slab, 3m x 4.5m shown in Figure 05.12, rests on the surface of a soil mass.…

A:

Q: 5- Determine the stress increase at point A due to the embankment load. 10.4 m 9.1 m Unit weight =…

A: Solution- The diagram is shown below, For  Load intensity (qo) is…

Q: The Infinite line load as shown in figure has an Intensity of 600 kN/m. Determine the vertical…

A: Given data,For an infinite line load as shown in the figure,Intensity of loading, q=600kN/mTo find…

Q: Problem 4 A thin-walled cylindrical pressure vessel has an internal diameter of d = 2 m and a wall…

A:

Q: The circular flexible area is uniformly loaded. Given: q = 320 kN/m2. Determine the vertical stress…

A:

Q: 8.5 The cylindrical tank with a spherical end-cap has an outer radius of 2 m and a wall thickness of…

A: To find out the longitudinal stress, hoop stess     ( Circumferencial stress)  and stress at end…

Q: Determine the normal stress in a ball, which has an outside diameter of 195 mm and a wall thickness…

A:

Q: A spherical tank has an inside diameter of 3.85 m. The tank is to contain gas at an internal…

A:

Q: 1. The cylindrical tank with a spherical end-cap has an outer radius of 2 m and a wall thickness of…

A:

Q: AN 8 MM THICK CYLINDRICAL STEEL TANK HAS AN OUTSIDE DIAMETER OF 600 MM AND A LENGTH OF 3 M. (a) WHEN…

A: Given  Thickness 8mm Diameter 600mm Assume unit weight of water 10kn/m^3

Q: Problem 3 The tube shown below has a uniform wall thickness of 12 mm. For the loading given,…

A: We have to determine the value of stress at point A and B in the given figure according to the given…

Q: 120 kPå 30kPa A 30KPA 40° 150 kPa

A: plane which has zero shear stress is called principle plane .  the normal stress occurring in these…

Q: Determine the normal stress in a ball, which has an outside diameter of 170 mm and a wall thickness…

A: Given- a ball inflated to a gauge pressure of 87kpa. Required-to find normal stress in a ball.

Q: 5 m +A 5 m 5 m 10 m

A: Given: A rectangular loaded area as shown below Required to determine a) Stress at a depth of 5 m…

Q: Problems for Practice Situation 4 A point load P-5 kN at the origin (0, 0, 0) of a ground surface…

A:

Q: Determine the value of maximum shear stress Maximum principal stress-25.92 MPa Minimum principal…

A: Given data in question  Maximum and minimum principal stress To find out  Maximum shear stress

Q: A 20 mm diameter hole is drilled on the centerline of a steel strap 50 mm wide by 5 mm thick,…

A:

Q: 10.11 Refer to Figure 10.42. Due to application of line loads q, and q2, the vertical stress…

A:

Q: b. Consider the downward flow of water through a layer of sand in a tank shown below. For the sand,…

A: solution given e=0.48 and G.S=2.7find saturated unit weight γsat=γwG+e1+e=9.812.47+0.481+0.48=19.55…

Q: The rectangular bar shown in the figure is subjected to a uniformly distributed axial loading of w =…

A: Total load due to udl isF=wd=110.035=0.385kNso,Maximum normal stress will be in section…

Q: A cylindrical pressure vessel is fabricated from steel plating that has a thickness of 20 mm. The…

A: given data A cylindrical pressure vessel has thickness, t= 20 mm diameter, d= 15 in.  length, l= 6.6…

Q: Assume segments AB, BC, and CD have a circular cross section, all with constant diameter 45mm.…

A: Given, diameter,d=45mm To find , Average normal stress in respective segments

Q: A concentrated load of 2500 kN Is applied at the ground surface. Determine the vertical stress at…

A: Given data,concentrated load of 2500 kN Is applied at the ground surface.Determine (1)the vertical…

Q: Assume segments AB, BC, and CD have a circular cross section, all with constant diameter 45mm.…

A: From segment AB:∑ Fx=0FAB-24=0FAB=24KNNormal stress in AB:σAB=FABA=FABπ4d2σAB=24,000Nπ4452=15.090Mpa

Q: Problem 3 The tube shown below has a uniform wall thickness of 12 mm. For the loading given,…

A:

Q: Refer to Figure 10.41. Determine the vertical stress increase, Ar, at point A with the following…

A: Vertical stress increase at the given point beneath the ground surface is given by a formula.…

Q: bi ELABORATE Try solving the following problem: Practice Problem: Refer to Figure 3.8. Determine the…

A:

Q: Determine the normal stress in a ball, which has an outside diameter of 165 mm and a wall thickness…

A:

Q: 1. From the given figure below, determine the following: a. Maximum shearing stress of the beam b.…

A: As per Bartleby guidelines we are supposed to do only 1st problem with its all three parts so I…

Q: Refer to Figure, q1 = 90 kN/m; q2 = 325 kN/m; x1 = 4 m; x2 = 2.5 m; z = 3 m. the vertical stress…

A: Two line loads are given q1 and q2 We are required to calculate the increase in vertical stress due…

Q: knowing that P = 18 Kips, determine the maximum stress when r = 0.45 in and r = 0.70 in

A: Given-  P = 18 Kips r = 0.45 in r = 0.70 in

Q: Refer to the figure below. Given: 91 = 100kN/m, q2 = 200 kN/m X1 = 3m, x2 = 3m, z = 3m Determine the…

A:

Q: Determine the magnitude of the maximum in-plane shear stress at point A (in MPa). 100 kN/m .A 1m 0.5…

A:

Q: meters and wall thickness of 3 mm is filled with 2.4 meter deep of water. Unit weight of water is…

A:

Q: The normal and shear stresses acting on one plane passing through a point in a soil mass are 120 psi…

A:

Q: A cylindrical compressed tank with closed ends is filled with air at a pressure of 500 kPa. The…

A: Given data- Pressure P=500 kPa=500×103 PaInner radius=2 mInner diameter d=4 m=4×1000 mmthickness…

Methods to Determine Vertical Stress

The load applied to the soil is transferred to the underground. The presence of water at soil pores and solid grains above the soil are the primary components that are responsible for the effective load transfer. Due to the load acting, the internal component of the soil or the underground formations undergoes deformations or a tectonic shift. The amount of deformation depends upon the amount of load acting on the soil surface, which indeed, depends on the weight of everything present above the soil. Due to this, the underground soil element develops internal stresses which try to resist the tectonic changes.