Determine the different heights h, that water will raise in three different capillary tubes, with diameters: dz = 0.00075 mm (corresponding to a fine clay sized particle), dɔ = 0.075 mm (corresponding to the smallest sand sized particle) and dz = 0.75 mm (corresponding to a medium sand sized particle). Assume that the surface tension is 0.075 N/m with an angle a = 3°. %3D hi

Determine the different heights h, that water will raise in three different capillary tubes, with diameters: dz = 0.00075 mm (corresponding to a fine clay sized particle), dɔ = 0.075 mm (corresponding to the smallest sand sized particle) and dz = 0.75 mm (corresponding to a medium sand sized particle). Assume that the surface tension is 0.075 N/m with an angle a = 3°. %3D hi

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter8: Stresses In A Soil Mass

Section: Chapter Questions

Problem 8.16P

See similar textbooks

Similar questions

The dam shown has a base of which 2m below the ground surface. The pressure distribution diagram at the base of the dam can be obtained from the equipotential lines as follows: k=4.5 m/day. if H=6m determine the seepage through the foundation.
The water table is located at a depth of 4.0 m below the ground surface in a deposit of sand 16.0 m thick (Fig. 1). The sand is saturated above the water table. The total unit weight of the sand is 25 kN/m3. Calculate the (a) the total pressure, (b) the pore water pressure and (c) the effective pressure at depths 0, 4.0, 10.0, and 16.0 m from the ground surface, and draw the pressure distribution diagram.
The sand layer shown is 2.5m thick. Beneath the sand layer is a 1.8m thick clay layer, underneath the clay layer is a solid rock. Water table is at depth of 0.9 m below the ground surface. SAND: Ymoist= 23KN/m3 ; Ysat= 21KN/m3 CLAY: Ysat= 23 KN/m3 ; LL= 42% e=0.7 A.) Compute the overburden pressure at mid-clay layer. B.) Find the maximum surface pressure without exceeding a 139.5mm settlement in clay layer if it is assumed to be normally consolidated. C.) If surface pressure is 70kpa and pre-consolidation pressure is 80kpa, find the settlement in clay layer.
11. A channel runs almost parallel to a river as shown in the figure. The water level in the river has an elevation of 36 m. and the elevation of the channel is 33 m. The river and channel are 600 m apart and a previous formation of the average thickness of 9 m and hydraulic conductivity of 0.80 m/hr joints them together. Compute the hydraulic gradient Compute the rate of seepage flow from the river to the channel per meter width in liters per day. If the seepage velocity is 0.048 m/day, compute the void ratio of the previous medium.
CALCULATION USING DARCY'S LAW An aquifer system is formed by two horizontal layers. Two piezometers were installed for monitoring, the distance between them is 885m. The upper layer (A) has a thickness of 39m and K = 1.3 x 10-5 m/s and the lower layer (B) has a thickness of 25m and K = 2.7 x 10-6 m/s. THE hydraulic load in the PZA is 60m and in the PZB it is 40m. Calculate the flow and the transmissivity of each layer.
A masonry dam has a coefficient of permeability in the vertical and horizontal directions of Kz=4m/day and Kx=5m/day, respectively. The difference in the head is 18m and the distance between the base of the dam and the downstream water surface is 18m. Assume z=35m and width of dam = 40m. a. Determine the seepage flow (m3/day) b Determine the uplift pressure (kpa) at A. c. Determine the uplift force (x10^3 kN) acting in the dam. Assume that the uplift pressure under the dam varies uniformly.
A dense silt layer has the following properties: void ratio = 0.75, specific gravity = 2.59. Free ground water is 9.49 m. below the ground. Capillary action rise will reach 6.69 meters. The soil above capilary action rise is dry while within the zone, it is saturated at 50.02%. Determine the effective pressure (in kPa) at a depth of 7.51 meters from the ground surface. Round off to three decimal places. Selected Answer: 128.657
The hydraulic gradient is a rock that is porous and permeable enough to transmit water easily. b the difference in hydraulic head between two points, divided by the distance between them. c rock that is low in permeability so that water flows very slowly through it. d a relationship of groundwater flow rate between two point to the difference in hydraulic head between them. 2. An artesian well is one in which a pressurized groundwater rises from a deep, unconfined aquifer. b water rises above the top of the confined aquifer without any pumping. c the well is horizontal and the water table is perched. d Paint colors are mixed. e the water is warm, fairly saline, and recharged by an affluent stream. 3. A cone of depression is a a solid or hollow object which tapers from a circular or roughly circular…
A soil profile consists of 2m of sand (γ=18kN/m³, kv=4 x 10-2m/day) over 3m of silt (γ=17kN/m³, kv=1 x 10-2m/day) over 2m of silt (γ=16kN/m³, kv=5 x 10-4m/day) over gravel. The water table is 0.5m below the ground surface. A piezometer placed at the top of the gravel layer measures a porewater pressure of 42kPa. Assuming a one-dimensional flow condition in the vertical direction, compute the flow rate in m³/day/m². Also compute, atmiddepth of the clay layer, the porewater pressure, total vertical stress, and effective vertical stress.
if Manning's N=0.023 and Hydraulic radius=3 m , then value of Chezy constant is ________?
Figure shows that the pipe flow of 50 m^3/hr, is driven by pressurized air in the tank. a) Determine the head loss in the “smooth” pipe in meters if the friction factor is 0.014. b) What gage pressure p1 in kPa, is needed to provide the given flow rate?
Define Active and Passive Lateral Pressures.