Determine the discharge rate in a 1.37-m diameter corrugated metal pipe (CMP) (n = 0.024) on a slope of 0.007 flowing full. What is the discharge rate if the water depth is 1.22 m? Compute the water depth for a discharge rate of 1.70 m/s. Use Figure 5.3 below. 1.0 0.8 0.6 0.4 0.2 D 0.000 0.2 0.4 0.6 2/2p 0.8 1.0 Figure 5.3 Discharge in a circular pipe flowing partially full with Manning "w" as a function of water depth.

Determine the discharge rate in a 1.37-m diameter corrugated metal pipe (CMP) (n = 0.024) on a slope of 0.007 flowing full. What is the discharge rate if the water depth is 1.22 m? Compute the water depth for a discharge rate of 1.70 m/s. Use Figure 5.3 below. 1.0 0.8 0.6 0.4 0.2 D 0.000 0.2 0.4 0.6 2/2p 0.8 1.0 Figure 5.3 Discharge in a circular pipe flowing partially full with Manning "w" as a function of water depth.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The specific discharge in a horizontal and rectangular channel is q = 1.44 m2/s and the water depth is y1 = 1.28 m. What is maximum hump elevation without chocking effect? a) 0.65 m b) 0.55 m c) 0.5 m d) 0.45 m
A trapezoidal notch of 1.2m wide at the top and 450mm at the bottom is 300mm high. Find the discharge through the notch if the head of water is 225mm. Assume C=0.60.
A trapezoidal channel with a bottom width of 5m and side slope of 1V:2H is constructed to convey a steady discharge to a hydropower installation. This is made up of concrete with a Manning's n = 0.016 and bed slope of 3V:2000H. a. Determine the discharge and velocity if the discharge has a 2m-depth of water? b. Calculate the depth if discharge is 35m³/s? c. As shown below, when flooded, the flow goes over the top of the channel. If the flood channels are 10 m. wide and with side slopes of 1V:3H, and roughness is n=0.035, what is the discharge for a flood level of 4m?
If the water surface elevation in reservoir B is 110 m, what must be the water surface elevation in reservoir A if a flow of 0.03 m3s is to occur in the cast-iron pipe? Use f = 0.021 for all pipes. Draw the HGL and the EGL, including changes in slope due to head loss. Neglect minor losses.
A rectangular channel 1.25m wide and 30m long with a flat bottom carries a flow of 0.5m3/s. The channel terminates in a free discharge. Plot a sketch of the water profile in the channel. Take n = 0.011. [10 Marks] b) Find the depth for uniform flow in a trapezoidal channel side slopes 1 in 2, and bottom width 3m, when the flow rate is 6m3/s if So = 0.0006 and n is assumed to be 0.016. Compute the corresponding value of e. [10 Marks]
A rectangular channel 3.6m x 1.8m deep discharge 6.8 cu.m per sec. If the same consideration have been used for a trapezoidal section having the same perimeter, what would have been the discharge possible with the swme hydraulics slope? In cu.m/s
The bed of a corrugated channel, with Manning’s coeffcient n =0.019 s/m^1/3 drops 25 m every 1500 m. The channel has a semi-circular cross section with total width of W = 10 m (i.e. radius of the semi-circle is 5 m). 1. Given that the stream has a water depth of h = 2.5 m, find the flow rate in the stream 2. A concrete divider with the same Manning’s coeffcient was installed at the middle of the stream. Given that the total flow rate in the stream stays the same, would the water depth in the stream change as a result of the divider? If so, would it increase or decrease? Would the stream velocity change? If so, would it increase or decrease? You may assume the thickness of the divider to be negligible.
Calculate the discharge in the concrete trapezoidal channel if the slope is 0.0002, the side slope is 1.5, the width of the channel is 6 m and the normal depth is 1.6 m. Consider Manning's coefficient of 0.013.
Hydraulic structure Two concrete pipes (n = 0.01) must carry the flow from an open channel half square section 2m wide and 1m deep (n = 0.01168) The slope of both structures is (0.0009). Determine the diameter of the pipes.
5. A tar coated (n = 0.014) triangular channel has 45ᵒ sides and slope of 0.0004. Compute the normal depth for a discharge of 140 ft3/s.
Plz, solve the two parts of this question. Hydraulics. Reg.No: 5395 Question. a). A lined rectangular channel (n = 0.015) has a flow depth of 2m and a bed slope of 1 in 1600. Width of a channel is equal to the last digit of your registration number in meters. Retaining the rectangular shape and same total perimeter of a lining, DISCOVER the change in discharge for a most efficient x-section of a channel, if the bed slope, channel width and manning’s n remain same. b).DISCUSS the critical depth, normal depth and hydraulic depth of flow for subcritical and supercritical flow in open channel.
A trapezoidal channel B=4.50m m=1.0 ,n=0.03 has a bed slope of S=0.003 The channel ends in a sudden drop. Calculate the GVF profile for a discharge of 25.0 m³/s