Determine the external reactions at A and F for the roof truss loaded as shown (positive answers are to the right and up). The vertical loads represent the effect of the supported roofing materials, while the 420-N force represents a wind load. 420 N y 260 N A 60° Answers: B. Ax i Ay = i Fy= i 480 N 60 30° 410 N G 9.5 m 420 N 30° E 30° N Z Z Z N N 250 N F x

Determine the external reactions at A and F for the roof truss loaded as shown (positive answers are to the right and up). The vertical loads represent the effect of the supported roofing materials, while the 420-N force represents a wind load. 420 N y 260 N A 60° Answers: B. Ax i Ay = i Fy= i 480 N 60 30° 410 N G 9.5 m 420 N 30° E 30° N Z Z Z N N 250 N F x

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The structure of a beam with single supports is subjected to a moment MA at the pinned end A, an inclined load FB applied at point B, and a uniformly distributed load with intensity q1 on the segment BC. Find the support reactions at joints A and C, then calculate the internal forces at the midpoint of BC. MA= 380 N.m FB = 200 N q1= 160N/m a= 3 m b= 2m
(a) Determine all reactions and bar forces pro-duced by the applied load in Figure P9.33. (b) If supportB settles 1 in. and support C settles 0.5 in. while the loadacts, recompute the reactions and bar forces. For all barsthe area = 2 in.2and E = 30,000 kips/in.2
Determine the magnitude of the bending moment at C. Assume a = 4.7 ft, b = 9.4 ft, c = 18.8 ft, w = 1130 lb/ft, and P = 3800 lb. Part 1 Determine the vertical reaction forces at B and D.Answer:By = lbDy = lb
given w = 8.2 kn/m and p = 15 kn for the beam below Calculate the vertical reaction at support A now. Provide your answer to 2 decimal places. Consider an upwards force as being positive, however only include a sign if the reaction is negative i.e. acts vertically down. Do not provide any units in your answer. Vertical reaction at A [kN] =
Calculate the support reaction at roller support C
The crate weighing 500N is supported by three ropes concurrent at B. Find the forces in ropes AB and BC.P = 600N.
In the figure on the right where there is a 50 N single load at point Bof the given rod system, (between AB: 4m / BC: 1m)a) find the support reactions?b) Immediately after support A, just before point Band immediately after and just before the C-bracketFind the cross section effects by cutting?c) Draw the cross sectional influence diagrams.
3. The force system has a resultant of 300 lb down to the right at 60 with the X axis. Compute the value of F and teta required to give this resultant.
a) The truss structure in Figure Q4 is supported at A and D with downward vertical load F1 acting at joint E and a downward vertical load F2 acting at joint C. The length of each truss member AB, BE, BC, CD and CF is 1.25 m. If F1 = 95 kN and F2 = 225 kN, determine the reaction force RA and RD at the supports A and D. Give your answers in kilonewtons (kN) to two decimal places. b) For the truss structure in Figure Q4, determine the forces FAE, FAB and FCF acting in members AE, AB & CF and clearly state if each member is in compression or in tension. Give your answers in kilonewtons (kN) to two decimal places. c) A solid homogeneous truss tie-rod has a diameter of 9.52 mm and an original length of 1.75 m experiences a stress of 600 MPa when placed under tension. If the material used for the truss tie-rod has a Young’s Modulus, E, of 5.8 x 1011 N/m2, calculate: (i) the tie-rod’s extension in millimetres (mm); (ii) the strain energy (U) in Joules; and (iii) the strain…
(a) Assuming that no loads act in Figure P9.16,compute the reactions if support B is constructed 0.48 in.too low. Given: E = 29,000 kips/in.2, I = 300 in.4. (b) Ifsupport B settles _32 in. under the applied loads, computethe reactions.
The frame shown in Figure is hinged at E and roller supported at A. Determine the horizontal and vertical components of the hinge forces at B. a.) Bh= 24 KN & Bv=56 KN b.) Bh=48 KN & Bv= 81 KN c.) Bh=24 KN & Bv= 81 KN d.) None of the Above e.) Bh= 48 KN & Bv=56 KN
Determine the external reaction at F for the roof truss loaded as shown. The vertical loads represent the effect of the supported roofing materials, while the 400-N force represents a wind load.