Determine the following of the truss shown using the method of consistent deformations: Answer: Horizontal Support Reaction lat A= k Axial force in member BF= Axial force in member DF= Vertical Support Reaction at D= E (6 in.2) F A, (6 in.²) (6 in.2) (4 in.²) (4 in.²) B (4 in.2) (6 in.²) 25 k 25 k -3 panels at 20 ft = 60 ft- E = 29,000 ksi C -28 k (6 in.2) (6 in.2) k k k D tp. 15 ft Dx

Determine the following of the truss shown using the method of consistent deformations: Answer: Horizontal Support Reaction lat A= k Axial force in member BF= Axial force in member DF= Vertical Support Reaction at D= E (6 in.2) F A, (6 in.²) (6 in.2) (4 in.²) (4 in.²) B (4 in.2) (6 in.²) 25 k 25 k -3 panels at 20 ft = 60 ft- E = 29,000 ksi C -28 k (6 in.2) (6 in.2) k k k D tp. 15 ft Dx

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

From the figure shown, a truss is subjected to loads PI = 15 kN, P2 = 15 kN and P3 = 25 kN at joint C, D and E respectively. Use SI = 3 m; S2 = 4 m Properties of diagonal members (2L75 x 75 x 6): Ag = 1858 mm2 Fy = 248 MPa rx = 22.9 mm ry = 33.2 mm Question: a) What is the axial force in kN, in member DI? b) What is the allowable stress in MPa, in member DI? c) Calculate the allowable load in kN, in member DI.
For the beam shown, determine the support reactions and draw the stress diagrams.shear and bending moment. EI is constant. Use the force method. I have a correct answer, it is: VA = 44.3 kN (↑); HA = 0 kN; MA = 34.3 kN.m (counterclockwise); VB = 38 kN (↑). I don't know how to get to this result, please show me how to get there step by step
Use either the Virtual Work Method or the Method of Consistent Deformation. Please state what you use and please show the complete solution Considering the beam shown in Figure 1, E = 200 GPa and I = 2x10 ^9 mm^4 Determine the vertical reaction at support A. Determine the horizontal reaction at support A. Determine the Moment reaction at support A. Determine the vertical reaction at support C. Determine the vertical deflection of point B due to the loads Determine the horizontal deflection of point B due to the loads Determine the total deflection of point B due to the loads with respect to its original location.
1) Calculate the beam reactions 2) Draw:  Deformed, Shear and Moment Diagram  Deformed Equation  Slope Equation 3) State of Efforts 4) Calculate the distance where the shear is zero and the moment is maximum. 5) Determine the Maximum Bending and Shear stresses of the beam and indicate where the points where they occur, if the section shown is used, draw the stresses that occur in the section of the beam 6) Determine the inflection point of the deformed curve 7) Determine the value of the deformation when x = 3.83 meters
A pin-jointed plane truss shown in Figure Q1 is supported by a roller at point A and pinned at point G. Vertical point loads of 5 kN are acting downward at points B, C and D. As a structural engineer, you are responsible to check the stability and analyse all of the members in the truss.c) Determine the internal force of each member by using an appropriate method?
A rigid bar XYZ as shown in the figure below is hinged at X and is supported at Y. If the deformation of end Z must not exceed 1.0 in, determine the largest possible load P that can be applied at point Z.
For the truss in figure below, the cross-sectional area of the truss members is A = 500 mm2 and Young’s modulus E = 200 GPa. Let P = 90.9 kN. a) Strain energy for truss AC. Enter your answer in J to 2 decimal places. Positive value indicates tension, negative value compression. b) Strain energy for truss AB. Enter your answer in J to 2 decimal places. Positive value indicates tension, negative value compression. c) Strain energy for truss BC. Enter your answer in J to 2 decimal places. Positive value indicates tension, negative value compression. d) Strain energy for truss BD. Enter your answer in J to 2 decimal places. Positive value indicates tension, negative value compression. e) Strain energy for truss DC. Enter your answer in J to 2 decimal places. Positive value indicates tension, negative value compression. f) Strain energy for truss DF. Enter your answer in J to 2 decimal places. Positive value indicates tension, negative value compression. g) Strain energy for truss FC. Enter…
Calculate the support reactions by showing that the following systems are isostatic. Mafsal (Turkish) = Joint (English)
Determine the bending stress (in Pa) at the top of the beam at point C for the beam shown belowif P = 1920 N, T = 4044 Nm, a = 0.81 m, b = 1.11 m, c = 0.98 m, w = 37 mm, and h = 73 mm. Round off the final answer to one decimal place.
Determine the axial force in members of the truss shown below using the method of consistent deformations. Express your answer in kips and use two decimal places. Note that if the axial force is compression consider negative sign in your final answer.
when the structure shown is unloaded, there is a 0.03 mm gap between the rigid bearing plate and the rigid bearing cam on bar B. determine the magnitude of the force P that will cause the axial stresses in bars A, B, and C to have the same magnitude. use the following properties:
A steel strut S serving as a brace for a boat hoist transmits a compressive force P = 63 kN to the deck of a pier as shown in the figure. The strut has a hollow square cross section with wall thickness t = 8 mm and the angle θ between the strut and the horizontal is 41°. A pin through the strut transmits the compressive force from the strut to two gussets G that are welded to the base plate B. Four anchor bolts fasten the base plate to the deck. The diameter of the pin is dpin = 19 mm, the thickness of the gussets is tG = 14 mm, the thickness of the base plate is tB = 10 mm, and the diameter of the anchor bolts is dbolt = 10 mm. Determine the bearing stress between the anchor bolts and the base plate in MPa.