Determine the force in member AE. if P =7.6 kN and L= 5 m Note: Negative if compression and Positive value if Tension RD

Q: Take 2 KN/m in place of 1.5. Determine support reaction

A: Given data : The value of point load P=3 KN The value of uniformly distributed load q=2 KN/m…

Q: Determine the force (kN) at member DO. 4 m C A 1 m 2 m 60 kN D 120 kN

A:

Q: Determine the force in member BD, in kN. 3.5 5.0 7.0 1.75 5 kN. B 5 m jc 10 kN 5m 2 m 3 m

A: It is To find the force in member BD-

Q: Determine the forcelin members Hlof the truss in kN, and state if the re in tension or compression.…

A: We can calculate member force in HI using methods of joints or by method of section. Here we have…

Q: Determine the forces in members BE and CE of the loaded truss. The forces are positive if in…

A:

Q: H 4.5 m 3 m E B 7 kN -12 m, 4 @ 3 m - 6 kN 4 kN Figure 1

A:

Q: Given the ngure below, del nine the tension fn the thi (in KN) initial pull of the motor is 0.20…

A:

Q: The structure is comprised of rigid bars AB and BCD supported by hinges at A and D. A steel rod at C…

A:

Q: Determine the value of the force P (kN)

A:

Q: Question 1. Determine the tension force in member C and its angle e for equilibrium. The forces are…

A:

Q: Consider the given plane truss supported at A and B as shown below. 20 kN E 2 m G 2m 2 m H 2 m F 5…

A: Take moment at A zero to find reaction at B

Q: A cantilever truss is pin-connected at joint D and is supported by a roller at G. Spacing of trusses…

A: Since it is said that wind load is normal in front  A,B,C,D So , take the plane passing A,B,C,D  as…

Q: Use the moment distrībution method to determine the support reactions for the following beam. The…

A:

Q: 4. Determine the location of the maximum moment on the beam in meters. 5. Determine the maximum…

A:

Q: Determine the area of the moment diagram of the structure P O(-PL^2)/2 (PL^2)/2 O(-2PL^21/3 O…

A: Given data in question  Cantilever beam  Span member length  Point load To find out  Area of bending…

Q: The member of the structure weights 200 lb/ft. Neglecting the weight of the member find the safe…

A: Find the safe value of P in kips

Q: 3. The rigid bar ABC is supported by a pin at A and a steel rod at B. Determine the largest vertical…

A: Draw the free-body diagram of the bar.

Q: Determine the forces in members BE and CE of the loaded truss. The forces are positive if in…

A: Given data: BC=CD

Q: Determine the forces in members BE and CE of the loaded truss. The forces are positive if in…

A: Given data in question  Load  Span member length  To find out  MEmber force

Q: Question 7 H -67.5 kN 3.6 m D 112.5 kN E F 3.6 m A B 6 m +4.5 m- Use portal method to analyze the…

A: Portal method works on the assumption that includes assuming a shear force in the columns of the…

Q: Determine the maximum flexural stress at 1 m from the support at D to E in MPa.

A:

Q: For the beam loaded as shown, determine the reactions at the support. w = 12 kN/m; P = 20 kN; L = 6…

A: To determine The support reactions R1 , R2 , H1

Q: 100 N 200 N E A B 2 m 1.5 m 3 m 11.5m 1.5 m 150 N

A:

Q: Example Determine the support reactions at the roller at A and the pin at B. Neglect the weight and…

A:

Q: y 2 kN 4 kN/m A 3 m -1.5 m 1.5 m

A:

Q: Solve the forces in the simple space truss shown if Figure Q2 using tension coefficients. P(-4;3;0)…

A:

Q: P2 B MATHalino.com D 5 m 4 m MATHalino.com

A:

Q: (b) Figure Q2(b) shows that the truss supports loads at point C and E. If the value of F = 3 kN,…

A: In this question, we shall first use method of sections to determine force in the member BE and then…

Q: Determine the forces in members EF, BF and BC. F 2.74 m 3.66 m 2.74 m B C 13.35 kN 2.74 m E.

A: Let,RA=vertical reaction at support A in upward directionHA=horizontal reaction at support A in…

Q: The beam is subjected to an internal moment of M = 140 kN.m. Determine the bending stress developed…

A:

Q: e the force in each m are in tension or comp 60 kN 40

A: Given:- forces=60kN,40kN To find:- force in each member

Q: Determine the forces in members BE and CE of the loaded truss. The forces are positive if in…

A:

Q: Determine the reactions of the beam using Force Method Analysis. Set A is fixed, B is roller and w =…

A:

Q: Determine the forces in members BE and CE of the loaded truss. The forces are positive if in…

A:

Q: If the force in member C is -4.3 kip, what is the force in member D? A

A: Given:- A truss is given  The force in member C of the truss = -4.3 kip To determine:- The force in…

Q: Q 3 Determine the moments at the supports, then draw the moment diagram. Assume B is a roller and A…

A: It is required to determine the fixed end moments. Consider member AB,

Q: For the frame below, F = 11.3 kips, a = 4 ft, b 8 ft, and c 3 ft. Determine the magnitude of the…

A: Given data F = 11.3 kips, a = 4 ft, b = 8 ft, and c = 3 ft

Q: Q2 / Determine the reactions at the supports. Assume B is hinge connected. El is constant .Use…

A: Load(P)=35 kN, The length of the span AB(LAB)=4 m, The length of the span BC(LBC)=7 M, The length of…

Q: P = SN kN 1. For the force in the figure, determine the rectangular components along u and v axes if…

A: GIVEN FORCE SYSTEM

Q: Determine the force in member AE of the loaded truss. The force is positive if in tension, negative…

A: Consider the figure, Here, T is the tension and C is the compression.

Q: B D. H. G. 6 @2m 12 m Determine the following: 1. The axial force on member DF. 2. The axial force…

A: To find force in member DF,EG,EF

Q: The beam is supported by a pin at A and a short link BC. If P = 5 kN and the diameter of the pin at…

A: When a structural component is stationary and the value of the load you are working on is a dead…

Q: G H -67.5 kN 3.6 m -112.5 kN E F 3.6 m 6 m -4.5 m- Use portal method to analyze the frame. Determine…

A:

Q: Using method of joints, solve for the reaction and forces of members CD, JK, CI and EJ using (1)…

A: Method of Joint : 1. The method of joints is a process used to solve for the unknown forces acting…

Q: Q.3. Determine the length b of the triangular load and its position a on the beam such that the…

A:

Q: he given struc

A: Take reaction at B as redundant :Deflection due to reaction =RBL33EIupDeflection due to load…

Q: B 1m 3KN E 2m 2.5 2m 1.5m 4KN 5KN 6KN A. SOLVE THE VERTICAL REACTION IN THE ROLLER SUPPORT. B. SOLVE…

A:

Q: Determine the force in member AB if P=20 kN Note: Negative value if compression and positive if…

A:

Q: For the truss shown in Figure 2.3b, determine the force in member KP ifx = 5 m, y =7 m and P = 7.94…

A: To find force in member KP

Q: X. kN 6 kN 6 KN F 2.75 kN 2.75 kN h A G E d. d d.

A:

Load on Structures

Civil engineers primarily deal with beams in their day-to-day applications. A beam is a structural member that resists shear loadings. There are various types of beams such as cantilever beam, simply supported beam, and over the hanging beam. All these beams have a different end and loading conditions.