Determine the force in member CD of the truss shown in the figure. Circled values are areas in square inches. E is constant. What is the horizontal Reaction at A? [Select] What is the Verticall Reaction at A? [S [Select] What is the Vertical Reaction at B? [Select] -10 ft What is the horizontal Reaction at C? [Select] What is the Vertical Reaction at C? [Select] B 30 k 15 ft- O 20 ft

Determine the force in member CD of the truss shown in the figure. Circled values are areas in square inches. E is constant. What is the horizontal Reaction at A? [Select] What is the Verticall Reaction at A? [S [Select] What is the Vertical Reaction at B? [Select] -10 ft What is the horizontal Reaction at C? [Select] What is the Vertical Reaction at C? [Select] B 30 k 15 ft- O 20 ft

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.10.13P: A large precast concrete panel for a warehouse is raised using two sets of cables at two lift lines,...

See similar textbooks

Similar questions

Hi, I have been given this pin-jointed frame analysis to solve (see pictures of the structure attached). Can you help me? The Figure 2 attached is a simplified structure to undertake a structural analysis on a concept design for a low cost stroller/buggy for children. The buggy consists of a number of metal sections that are pin-jointed together. The buggy is designed to accommodate a child of mass no more than 20 kg, sat on the seat which is supported at four points (Fc) on the frame of the buggy. Assume that the weight of the child is equally distributed across all of the points indicated on Figure 2 as Fc. Assume that there are no additional forces applied to the handle of the buggy, that the buggy is static (stationary) and that the buggy, and the elements of the frame have no mass. At points A and G, there are roll supports. At Points B, F and D there are the pin supports. I am required to determine the following: 1) Draw a free-body diagram of the structure 2) Simplify the Free…
we want to build a single-rail overhead crane in the workshop.when the load reaches the extreme point, it is 1800 mm away. the rail-shaped profile iron of the crane is connected from point B to point A by rope.the tensile stress of the rope is = 600 mpa. and the cross-sectional area is a=802 mm.according to other dimensions given (a=850mm b=1500 mm), this vince can hang No more than how many kg of load.(G=?)
A team of design engineers are designing an amusement park structure as in Figure 2below. The horizontal beam supporting the gondolas at both ends are supported by 2vertical bars, bar EB and bar CF with a cross sectional area of 11,100mm2 and 9,280mm2each. Gondola 1 (left) weighs 380 kN and Gondola 2 (right) weighs 360kN respectively. Due to theweight of both the gondolas, the design team needs to investigate the verticaldisplacements of both ends of the horizontal beam at A and D. You are required to helpthem analyze and calculate the vertical displacement at both ends due to the weight ofthe gondolas.
For the truss given below, it is desired to determine the normal efforts that act on the members, so that, thus, possible constraints for its design are possible. Consider that at point A there is a second gender support; and at point D, a first-class support. As this is asked: what is the effort acting on bar AB? Is it guidance or assessment?Source: Hibbeler (2004, p. 588). HIBBELER, R. C. Resistance of Materials. 5. ed. Rio de Janeiro: Technical and Scientific Books Publisher, 2004. Question 1 options: a) A compression force of 100 kN acts on bar AB. B) A tensile effort of 100 kN acts on bar AB. c) A compressive force of 141.42 kN acts on bar AB. d) A compression force of 200 kN acts on bar AB. e) A tensile effort of 141.42 kN acts on bar AB.
What is the shear stress, fv, for the glue of the lap of the connection with P= 15,000 lb? What is the axial stress due to tension, ft, on the thinner of the two plates?
A board of mass mand length l is attached to a wall and a rope that makes an angle of theta, as shown. A block of mass M hangs from the right end of the board. Suppose m = 2.0kg, L = .60m, M = 0.50kg, and angle(theta) = degrees. a. Using numbers, what is the magnitude of the tension force in the rope connecting the board and wall? b. Using numbers, what is the magnitude of the force applied by the hinge? c. Using numbers, in what direction does the force applied by the hinge point?
Floor joists are structural members which support flooring in structures, as in the diagram on the right. The floor sits upon the minor length of the joist, and the joists are set at equal spacing to reach the desired floor stiffness. How many 2x6 joists would it take to equal the floor stiffness of the same floor supported by ten (10) 2x12 joists of the same species?
1. A circular cylinder with inside diameter of 10 cm which carries a compressive force equivalent to 400,000 N. What will be the outisde diameter of this cylinder if the allowable stress is 120 megaPascal. 2. A diagram or a curve which is a used as a reference to picture the internal forces in a beam 3. Maximum M occurs when the _______________ is ______________. 4. Within the region of positive moment, the elastic curve is concave __________ 5. There must be a/ an _________________ where the curve changes from concave down to concave up
Question 1) in FIG loading condition is given beam F force F = 65 kN , first distributed load W 1 = 41 kN / m , w 2 distributed load w 2 = 51 kN / m , θ angle θ = 48 ° and L length of L = 5 m . According to this; Question 1-A) B at the point y direction ( B y ) Determine the support reactions. (Enter yourresultwithout writing kN units.) Question 1-B) to the point in y direction ( A y ) Determine the support reactions. ( Enter yourresult without writing kN units.) Question 1-C) to the point in x direction ( A x ) Determine the support reactions. ( Enter yourresult without writing kN units.)
Table 1 : F= 585 lb, P = 215 lb, X= 5 ft, Angle of the inclined bars of truss = 30°
The truss shown at left is:a. Internally determinateb. Internally indeterminateSelect one answer and briefly explain your choice.
The mechanism shown in the figure controls the lifter. Calculate the reactions on CDE as the weight supported by the platform is W W(N)= 2800, L1(m)=0.6, L2(m)=0.6 , L3(m)=0.2 1) For three dimensional problems, please use vector notation.2) State what all the transactions you have done. All intermediate actions you have to doshow clearly.3) Please write the units next to the values you find.4) In the related questions, please draw the free body diagram.