Answered: Determine the force Prequired to…

Determine the force Prequired to maintain the 165-kg engine in the position for which 0 = 40°. The diameter of the pulley at Bis negligible. 2.4 m B 2.4 m 165 kg Answer: P= i N

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter6: Beams And Cables

Section: Chapter Questions

Problem 6.90P: The 14-kN weight is suspended from a small pulley that is free to roll on the cable. The length of...

See similar textbooks

Related questions

Q: 86. The uniform 100-N (* 10-kg) ladder rests on the rough floor for which the cocfficjent of static…

Q: Determine the required mass of the lamp that can be suspended in the position shown for equilibrium.…

Q: Q1- if the 5 kg block is suspended from the pulley B and the sag of the cord is d=0.15m determine…

Q: The 54-kg homogeneous smooth sphere rests on the 28° incline A and bears against the smooth vertical…

Q: The 46-kg homogeneous smooth sphere rests on the 32° incline A and bears against the smooth vertical…

A: When an amount of push or the pull applied on the object, it has the ability to change its state…

Q: Q1- if the 5 kg block is suspended from the pulley B and the sag of the cord is d=0.15m determine…

Q: The mass center G of the 1350-kg rear-engine car is located as shown in the figure. Determine the…

Q: Q2/. The automobile has a mass of 1 Mg and center of mass at G. Determine the towing force F…

A: Consider the below FBD for calculation: Based on the data given in question, m = 1 Mg = 1000 kgW =…

Q: 1. If the spring DB has an unstretched length of 2 m, determine the stiffness of spring to hold the…

Q: ~4%3D0.2 BA D 4m Hi =0.2 -7.5 m-

A: To determine the weight of the block D that can support the pole ABC.

Q: The man uses the hand truck to move material up the step. The truck and its contents have a mass of…

A: Given data mass of truck (m) = 50 kg To determine Normal reaction on both wheels if the minimum…

Q: 0.25 m 0.25 m 1.5 m E 30° H D 10° 2 m 60° 0.5 m

Q: Determine the force P required to maintain the 150-kg engine in the position for which e = 22°. The…

Q: UNIVERSSITY O F LIVERPOOL Ei POL UNIVERSITY OF CIAL NJVERSITY OF UNIVERSITY OF NCING LIVERP 毛我S1T…

A: Calculated vertical force P and normal reaction force N on the tire.

Q: Quiz: Determine the force P required to maintain the 200-kg engine in the position for which 0 =…

Q: The 20-kg homogeneous smooth sphere rests on the two inclines as shown. Determine the contact forces…

A: Given data Mass of sphere = 20kg

Q: Determine the force P required to maintain the 200-kg engine in the position for which 0 = 30o. The…

Q: Determine the magnitude of the pin reaction at A and the magnitude and direction of the force…

A: Given Data All dimentions are modified into the 1.1 m The mass of the object is modified into 175 kg…

Q: Determine the force acting along the axis of each of the three struts needed to support the 500-kg…

Q: The automobile has a mass of 2 Mg and the center of mass at G. Determine the towing Q3 force F…

A: Given Data M=2000 kg μs=0.3

Q: The mass center G of the 1400-kg rear-engine car is located as shown in the figure. Determine the…

A: When a body is in equilibrium condition then it simply means that the net horizontal as well as net…

Q: Determine the length of spring CD so that the 10-kg sphere can be suspended in the position shown.…

A: Given data: Un-deformed length of spring, LCD = 0.4 m. Stiffness of spring, kCD = 300 N/m. Mass of…

Q: The mass center Gof the 1400-kg rear-engine car is located as shown in the figure. Determine the…

Q: The mass center G of the 1470-kg rear-engine car is located as shown in the figure. Determine the…

Q: Determine the force P required to maintain the 160-kg engine in the position for which e = 26°. The…

A: Given data: Mass of the engine, m = 160 kg. Calculate the weight of the engine, W=mg=160 kg×9.81…

Q: Determine the required length of cord AC , so that the 8-kg lamp can be suspended in the position…

Q: Determine the force P required to maintain the 200-kg engine in the position for which 0 = 30o. The…

Q: Determine the minimum force P required to hold the 10 kg mass in equilibrium as shown. (N) 1.5 m…

A: Given data: The hanging mass is, m = 10 kg. Calculate the angle made by cable AB with horizontal.…

Q: 05: The 50-kg homogeneous smooth sphere resèts on the two inclines. Determine the contact forces at…

Q: The structure consists of a spring CD and a solid member ABC with a slot at B. The peg at B fits…

Q: The 46-kg homogeneous smooth sphere rests on the 42° incline A and bears against the smooth vertical…

Q: Determine the force P required to maintain the 195-kg engine in the position for which 0 = 29°. The…

Q: Determine the force P required to maintain the 200-kg engine in the position for which e = 30o. The…

Q: Determine the components for the forces at A and D. The mass of the cylinder is 50 kg. 0.8 m 0.8 m…

A: Given : AD = 1.2 m AC = 1.6m

Q: The 79-kg homogeneous smooth sphere rests on the ( 2.3/2.4) incline A and bears against the smooth…

Q: The 30 kg block is supported by two springs having the stiffness shown. Determine the strech of…

A: Consider the free body diagram: tanθ=0.30.4θ=36.86°tanϕ=0.40.4ϕ=45°Applying Lami's…

Q: The 53-kg homogeneous smooth sphere rests on the 40° incline A and bears against the smooth vertical…

Q: The mass center G of the 1405-kg rear-engine car is located as shown in the figure. Determine the…

A: To Find : The normal force under each tire. Given : The mass of car m=1405 kg. FBD: The free body…

Q: (i) Determine the force P required to maintain the 200 kg engine in the position for which which 0 =…

A: Solution: Free body diagram of the force acting at C is shown below

Q: Determine the force P required to maintain the 155-kg engine in the position for which 0 = 34°. The…

Q: Determine the force P required to maintain the 240-kg engine in the position for which = 26°. The…

Q: 1. Determine the force P required to maintain the 200-kg engine in the position for which 0 = 30°.T…

A: Given data: The given mass is M = 200 kg. From the geometry, ∠ABC=∠ACB…

Q: Q3 Determine the force acting along the axis of each of the three struts needed to support the…

Q: s00 Ib- 8 ft U ZI

Q: The plate has a weight of W with center of gravity G. Determine the distance, d, along line GH where…

Q: The mass center G of the 1400-kg rear-engine car is located as shown in the figure. Determine the…

Q: A hand trolley is used to move a crate weighing 150 Ib down the ramp as shown below. The center of…

A: Given Data Weight of crate is : W=150 lb Now draw the free body diagram

Q: The crate has a weight of 550 lb. Determine the force in cable BA. B (3 30% A

Q: If the 5-kg block is suspended from the pulley B and the sag of the cord is d= 0.15 m, determine the…

A: Given data: Mass of the block, m = 5 kg. Draw the free-body diagram of the system, Calculate the…

Q: The grinder has a force of 400 N in the direction shown at the bottom. The grinder has a mass of 300…

A: Given: Let us consider the given image, Force, F=400 N Mass, m=300 kg To find: The force of…

Question

Determine the force P required to maintain the 165-kg engine in the position for which 0 = 40°. The diameter of the pulley at
Bis negligible.
2.4 m
2.4 m
P
165 kg
Answer: P =
i

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Similar questions

Determine the smallest horizontal force P that would push the homogeneous cylinder of weight W over the curb. Neglect friction.
The 80-kg crate has its center of gravity at G. Determine the smallest force P that will initiate motion if =35.
The homogeneous plate of weight W is supported by a ball-and-socket joint at D and three wires. Draw the FBD of the plate and count the unknowns.
The homogeneous bar AB weighs 25 lb. Determine the magnitudes of the forces acting on the bar at A and B. Neglect friction.
The 400-kg drum is held by tongs of negligible mass. Determine the magnitude of the contact force between the drum and the tongs at D.
Determine the horizontal force P that would keep the uniform 12-kg rectangular plate in the position shown.
The 40-kghomogeneous disk is placed on a frictionless inclined surface and held in equilibrium by the horizontal force P and a couple C (C is not shown on the figure). Find P and C.
The homogeneous 240-lb bar is supported by a rough horizontal surface at A, a smooth vertical surface at B, and the cable BC. Draw the FBD of the bar and count the unknowns.
The 40-lb spool is suspended from the hanger GA and rests against a vertical wall. The center of gravity of the spool is at G and the weight of the hanger is negligible. The wire wound around the hub of the spool is extracted by pulling its end with the force P. If the coefficient of static friction between the spool and the wall is 0.25, determine the smallest P that will extract the wire.
The 40-kg homogeneous disk is resting on an inclined friction surface. (a) Compute the magnitude of the horizontal force P. (b) Could the disk be in equilibrium if the inclined surface were frictionless?
The spring attached to the homogenous bar of weight W is undeformed when =0. Determine the smallest spring stiffness k for which the =0 equilibrium position will be stable. Use W = 10 lb, a = 24 in., and b = 6 in. Assume that the spring remains horizontal, which is a valid approximation if is small.
The 14-kN weight is suspended from a small pulley that is free to roll on the cable. The length of the cable ABC is 20 m. Determine the horizontal force P that would hold the pulley in equilibrium in the position x=5m.