Determine the in figuere. s efficiency of the fin shown Tip of the fin is adiabatic Accept it as an one-dimensional heat transfer. in a Continuous regime for the thin-tip air foil with the Shape shown in figure.

Determine the in figuere. s efficiency of the fin shown Tip of the fin is adiabatic Accept it as an one-dimensional heat transfer. in a Continuous regime for the thin-tip air foil with the Shape shown in figure.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter7: Forced Convection Inside Tubes And Ducts

Section: Chapter Questions

Problem 7.31P

See similar textbooks

Related questions

Q: Determine the reactions to the structure Af 5 ft 8P 5 ft 5 ft 15P 5P B

Q: F(kN) = x¹ + 2x orce to displacement at 1 cm by dith

Q: A force of 1000 lb is applied to the 600-lb horizontal beam supported by a hinge at A and a roller…

Q: Otto Cycle 1. Why are high compression ratios not used in spark ignition engines? 2. How does the…

Q: can you resolve the problem but with 10mm diameter, l=100mm, P=7850N, change in diameter =…

Q: ꜱʜᴏᴡ ᴛʜᴇ ꜰᴜʟʟ ᴅᴇʀɪᴠᴇ ᴇQᴜᴀᴛɪᴏɴꜱ ᴏꜰ ʙʀʏᴛᴏɴ ᴄʏᴄʟᴇ

A: Given: ꜱʜᴏᴡ ᴛʜᴇ ꜰᴜʟʟ ᴅᴇʀɪᴠᴇ ᴇQᴜᴀᴛɪᴏɴꜱ ᴏꜰ ʙʀʏᴛᴏɴ ᴄʏᴄʟᴇ

Q: Determine the reactions to the structure w2 = 200 lb/ft w1 = 100 lb/ft 15 ft 4000 lb 5 ft

Q: A smooth aluminum sphere hangs in air on a 0.5 m-long cable. The sphere has a diameter of 10 cm and…

A: (a) To find: The magnitude of drag force. Given: The weight of the sphere is W=1.5 N. The radius of…

Q: 2. 100 kN/m 3 200 kN-m 5 100 kN/m 10 ►x (m)

A: To draw: The shear force and bending moment diagram. Load diagram: The load diagram is shown below.

Q: Heat transferred from the higher and lower temperature reservoirs are and , respectively. Select…

Q: A thermal power plant generates 50mw to market and has an efficiency of 54%. Consider that It uses…

Q: A rectangular wing on an aircraft has a chord length of 1.6 m and span of 11 m flying in sky at the…

A: Given:Chord length, L=1.6 mSpan, S=1 1 mSpeed of an aircraft, U=195 km/h=195*1033600m/sTotal…

Q: A 2 x 2 m flat plate solar collector for domestic hot water heating is shown in the figure. The…

A: Given Data: Energy supplied to the water = 316.75 W/m2 cost of electricity = $0.13/kwh Efficiency of…

Q: Determine the temperature distrubition of the fin shown in figuere. Tip of the fin is adiabatic…

Q: Liquid fuel of kinematic viscosity 2.37x10-6 flows through the pipe of diameter 15 cm. Determine the…

Q: 14 A smooth sphere of diameter d=1 cm falls at constant velocity through water.

Q: A thin two dimensional member with thickness t is loaded by constant traction 00 at one end and…

A: Solution: Given Data: To Find:

Q: What material is the piston? None of these answers are correct Steel Cast iron O Aluminum

A: Given: To select the correct option for the material of the piston.

Q: Link AB is moving in circular motion about point A as shown. Link CD is moving in circular motion…

Q: The slender bar AB with a mass of 60 kg and a length of 4 m is secured by a cable at C, and pivoted…

A: Introduction In this problem, we will calculate the tension in the cable BC and construct the…

Q: A kiloJoule/meter ( kJ/m) is ?

A: kj/m it is just showing energy grediant . distribution of energy or variation of energy along the…

Q: Water at an average temperature of 23 deg C flows through a 10-cm diameter pipe that is 2.5 m long.…

A: Given: Tin = 23 deg C Diameter , D = 10-cm Length, L = 2.5 m long. Ts = 100 deg C. convective heat…

Q: Brayton Cycle 1. What is the back work ratio? How do back work ratio effect on the overall…

Q: An aluminium rod fits inside a steel tube. The diametral clearance between the rod and the tube is…

Q: In a steady adiabatic flow through a duct with no shaft/electrical work and no change in elevation…

Q: QUESTION 10 The Kelvin-Planck and Clausius statements of thermodynamics are equivalent. In order to…

A: Option (B) is correct,remaining are incorrect.

Q: 2. The cylinder shown below with mass M and radius R is held by a hand that is accelerated upward so…

Q: Who was responsible, using observation and a stopwatch, in developing standards used to teach…

A: Frederick Winslow Taylor.

Q: Match the process, positions, and parts of an internal combustion engine using the figure.

A: For given diagram followings are the notation, A- Exhaust valve B- Intake valve C-Intake stroke…

Q: What is the required insulation for a 270 ft long pipe with inner radius 3.55 inches. Foam will be…

A: Given: Length, L=270 ft Inner Radius, r = 3.55 in Thermal conductivity = 0.02 W/mK To find: Radius…

Q: Construct a qualitative work-energy bar chart for a process that is consistent with the equation…

A: Given: To find: Qualitative work energy bar chart

Q: What is the lowest temperature in degrees Celcius? Question 2 What is the lowest temperature in…

A: Temperature:- It is a measure of degree of hotness or coldness of any body , because of which, heat…

Q: A Carnot cycle takes in 108 kW of heat from a high-temperature reservoir at 500 C. At what rate is…

Q: The thin rectangular block is supported at its corners by small rollers resting on smooth horizontal…

Q: If cables BD and BC can withstand a maximum tensile force of 17 kN, determine the maximum mass of…

Q: A metal axle with second moment of area of 3,313.5 mm and radius of 15 mm is subjected to two…

Q: A 3.2-kg piece of putty is dropped 2.3 m onto the initially stationary block, which is supported by…

Q: A spherical bowling ball with mass m = 4.6 kg and radius R = 0.105 m is thrown down the lane with an…

Q: A humidifier in an air heating duct handles 3000 CFM, and increases the moisture content of the air…

A: Give Data: Air handling Duct Flow rate V˙= 3000 CFM Moisture Content of air goes from 30g/lb a.s.…

Q: a) Use the model above, determine the resonant frequency of a rectangular plug-in epoxy fiberglass…

A: To find: The frequency of the PCB. Given: The length of the PCB is a=9 in. The width of the PCB is…

Q: 7.17. When oil (kinematic viscosity 1 × 10-4 m²/s, specific gravity 0.92) flows at a mean veloeity…

Q: Equation 2 (M) is a second order differential equation that models the relationship between the…

A: Solution: Given Data: md2xdt2+Kddxdt+Ksx=FinFin=2 Nx(0)=0dx(0)dt=0m=10 kgKd=50 N-s/mKs=80 N/m To…

Q: 4. A disk of mass M and radius R is free to rotate about a horizontal axis through its center. A…

A: To find: The linear acceleration of mass, the angular acceleration of the disc, the tension in the…

Q: The bracket BCD is hinged at C and attached to a control cable at B. For the loading shown,…

A: Given data:- a=0.11 m Force applied (from C)= 240 N at 0.4 m and 240 N at 0.8 m To find:- Reaction…

Q: ㅗ Fo 고 -1층~ 1호1 4급 휴미 유 Drill Ka

A: Given: Draw the isometric view

Q: 7.38 Air Hows steadily into a nozzle at 0.125 kg/s, 500 kPa, 750°C and a low velocity. If it flows…

A: As per the bartleby code of conduct it is recommended to answer the first three parts of the sub…

Q: In a 2D dimension incompressible flow , if the fluid velocity components are given by u = x-4y , v =…

A: Given:The fluid velocity components are given as:u=x-4yv=-4x

Q: A beam section as shown in the sketch is subjected to a bendingmoment of Mx = 4 kN.m and a shear…

A: Given data, The given section is To 4) Draw the stress condition below the flanges, at the centroid…

Q: Wheels A and B are uniform 16.1-1b cylinders with frictionless axles as shown. A 32.2-lb box C with…

A: To find: The acceleration of the box. Given: The diameter of the cylinder, D = 0.3048 m. The…

Q: Air flows in a pipe under fully developed conditions with an average velocity of 1.25 m/s and a…

A: Given data as per the question The velocity of air in pipe =1.25 m/s Diameter of pipe =4 cm Length…

Concept explainers

Conduction and Convection

When energy travels from one object to another it is said to have undergone heat transfer. Heat transfer is nothing but the transfer of thermal energy or internal energy from one thing to another, like e.g., when a vessel with water, kept on top of a burner, heats up because of the flame underneath it.

Question

Tb=250°C
8mm
-120mm
-L= 50mm
Determine the
in figuere.
K= 300 W
mk
h=160W/m²K
key
efficiency
To = 32°C
Imma
n fin = ?
of the fin shown
Tip of the fin is adiabatic
Accept it as an one-dimensional heat transfer. in a
Continuous regime for the thin-tip air foil with the
Shape shown in figure.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 9 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

4.) A 15-cm-diameter steam line carries saturated steam at 6 MPa and is located in a tunnel with stagnant air with a temperature of 50oC. The outside unit convective coefficient is 8.5 W/m2-K. The steam line is covered with 3 cm of 85% magnesia insulation. It is decided to reduce the heat loss by one-half. How much 85% magnesia insulation is required? Neglect thermal resistance of pipe and inside surface.
Question - Maddy found the value of heat transfer coefficient 26 W/m^2 °C and faces the difficulties in conversion of si units to english units , so help him in conversion by conversion factors between watt to btu/h and m to ft and °C to °F
Hot exhaust gases leaving a stationary diesel engine at450°C enter a l5-cm-diameter pipe at an average velocity of3.6 m/s. The surface temperature of the pipe is 180°C. Deter-mine the pipe length if the exhaust gases are to leave the pipeat 250°C after transferring heat to water in a heat recovery unit.Use properties of air for exhaust gases.
What is the value of the heat transfer coefficient for air at 37 ° C flowing at 5 m / s perpendicular to a 10 cm x 10 cm square pipe at 93 ° C? h = 23kcal / hm ^ 2 ° C around this value
Water is heated at a rate of 10 kg/s from a temperature of 15°C to 35°C by passing it through five identical tubes, each 5.0 cm in diameter, whose surface temperature is 60.0°C. Estimate (a) the steady rate of heat transfer and (b) the length of tubes necessary to accomplish this task.
Consider a house that is maintained at a constanttemperature of 22°C. One of the walls of the house has threesingle-pane glass windows that are 1.5 m high and 1.8 mlong. The glass (k = 0.78 W/m·K) is 0.5 cm thick, and theheat transfer coefficient on the inner surface of the glass is8 W/m2·K. Now winds at 35 km/h start to blow parallel to thesurface of this wall. If the air temperature outside is -2°C,determine the rate of heat loss through the windows of thiswall. Assume radiation heat transfer to be negligible. Evaluatethe air properties at a film temperature of 5°C and 1 atm.
Q3: Air flows across a 20-cm-square plate with a velocity of $ m/s. Free-stream conditions are 10-C and 0.2 atm. A heater in the plate surface furnishes a constant heat-flux condition at the wall so that the average wall temperature is 100-C. Calculate the surface heat flux and the value of h at an x position of 10 cm. Answers: Q= 1414 W, b= 13.3 Wm?.C
An average man has abody surface area of 1.8m2 and a skin temperature of 33degrees celcius .The convection heat transfer coefficient for a clothed person walking in still air is expressed as {h,8.6V^0.53}FOR 0.5<v<2m/s,where V is the walking velocityin m/s.Assuming the average surface temperature of the clothed person to be 30degrees celcius, determine the rate of heat loss from an average man walking in still air at 10degrees celcius by convectionat a walking velocity of (a)0.5m/s (b)1.0m/s (c)1.5m/s (d)2.0m/s
For internal flow with fully developed flow condition The velocity profile .................... change and the thermal profile .............................. change in the direction of flow Please fill the blank Blank 1 ( Does or does not) Blank 2 ( Does or does not )
Flat-plate solar collectors are often tilted up towardthe sun in order to intercept a greater amount of direct solarradiation. The tilt angle from the horizontal also affects therate of heat loss from the collector. Consider a 1.5-m-highand 3-m-wide solar collector that is tilted at an angle u fromthe horizontal. The back side of the absorber is heavily insulated.The absorber plate and the glass cover, which arespaced 2.5 cm from each other, are maintained at temperaturesof 80°C and 40°C, respectively. Determine the rate ofheat loss from the absorber plate by natural convection foru = 0°, 30°, and 90°.
Hot air at 60°C leaving the furnace of a houseenters a 12-m-long section of a sheet metal duct of rectangularcross section 20 cm * 20 cm at an average velocityof 4 m/s. The thermal resistance of the duct is negligible,and the outer surface of the duct, whose emissivity is 0.3,is exposed to the cold air at 10°C in the basement, with aconvection heat transfer coefficient of 10 W/m2?K. Taking thewalls of the basement to be at 10°C also, determine (a) thetemperature at which the hot air will leave the basement and(b) the rate of heat loss from the hot air in the duct to thebasement. Evaluate air properties at a bulk mean temperatureof 50°C. Is this a good assumption?
Hot air leaving the stove in the kitchen of a house at 70 0C, with a square section of 22 cm x 22 cm.sheet metal enters the 12 m long section of the channel with a speed of 6 m/s. Emissivity 0.3The outer surface of the duct, whose thermal resistance is neglected, is located in the basement of the house at 14 0C and 12 W/m2.It is in contact with cold air with 0C convection heat transfer coefficient. Basementtaking the wall temperatures of the floor to 14 0C.Find the rate of heat loss from the hot air in the duct to the floor.