Answered: Determine the largest length of a W10 *…

Determine the largest length of a W10 * 12 structural A992 steel section if it is pin supported and is subjected to an axial load of 28 kip. Use the AISC equations.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter11: Columns

Section: Chapter Questions

Problem 11.9.7P

See similar textbooks

Related questions

Q: ソーH 12 ft

A: As per given question Length of column=12 ft Stress=50 ksi We have to determine the largest axial…

Q: A W14 * 30 structural A-36 steel column is pin connected at its ends and has a length L = 10 ft.…

A: Write the values of the W14X30 structure. Write the properties of A-36 steel. Write the expression…

Q: Q2/ Determine the maximum allowable load P that can be safely suppom 1.5 in. and b-4 in. The wood…

A: t=1.5inb=4inσfail=2ksiζfail=2ksiFOS=1.5 To-Find:- P=?

Q: *R17-8. The W200 × 46 wide-flange A992-steel column can be considered pinned at its top and fixed at…

A: Write the properties of A992 steel. Write the properties of the W200X46 flange.

Q: A 6061-T6 aluminum alloy solid circular rod of length 4 m is pinned at one end while fixed at the…

A: Given data: The length of the rod is L=4 m. The axial load on the truss is P=15 kN. The factor of…

Q: Using the NFPA equations of Sec. 13.6 and Eq. 13–30, determine the maximum allowable eccentric load…

A: Given: The length of the column, L = 12 ft The width of the column, b = 6 in The height of the…

Q: Determine the maximum allowable eccentric load P that can be applied to the wood column. The column…

Q: The A-36 stee (Fy= 250 MPa) W 200 x 46 member shown in Fig. is to be used as a pin- connected…

A: Given data: The length of the beam is, L=4 m. The yield stress is, Fy=250 MPa. Refer to the table…

Q: The A992 steel rod BC has a diameter of 50 mm and is used as a strut to support the beam. (Figure 1)…

Q: For a W14 x 53 column of A992 steel, 45 ft tall, determine the available load capacity when the ends…

A: Given Length, L = 45 ft = 13.71 m Find Calculate the Load capacity

Q: The W200 * 46 wide-flange A992-steel column can be considered pinned at its top and fixed at its…

A: Obtaining the properties of A992 steel column from the standard properties of steel: Modulus of…

Q: Check if the wood column is adequate for supporting the eccentric load of P = 800 lb applied at its…

A: Write the properties of the wood. Write the expression of the slenderness ratio. Write the…

Q: Select the lightest W shape that will act as a column 8 m long with hinged ends and support an axial…

A: Given Load, F = 270 kN Stress = 200 MPa Length, L = 8 m Find Lightest W shape

Q: Assume that the factor of safety with respect to buckling is 2.0 and the column is made of Steel…

A: Given: F.O.S = 2.0 L2 = 2 m For A992 Structural steel, Young's modulus is E = 200 GPa = 200 x 109…

Q: The tube is 0.5 in. thick, is made of aluminum alloy 2014-T6, and is ixed connected at its ends.…

A: Given data as per the question The thickness of the tube = 0.5 in Length of the tube = 12 ft = 144…

Q: *17-8. The W360 x 57 column is made of A-36 steel. Determine the critical load if its bottom end is…

A: Given data: The length of the column is; L = 6 m. The material of column is A-36 steel. The column…

Q: The W12 * 50 is made of A992 steel and is used as a column that has a length of 20 ft. If the ends…

A: Given, From standard tables of Beams for W12×50 beam, A = 14.7 in2 I= 56.3 in4 For A992 Steel, E =…

Q: The linkage is made using two A992 steel rods, each having a circular cross section. If cach rod has…

Q: A W12 * 26 structural A992 steel column is pin connected at its ends and has a length L = 11.5 ft.…

A: Given data: The structure of the column is: W12 X 26 The eccentricity of the column is: 6 in. The…

Q: 17-9. A steel column has a length of 9 m and is fixed at both ends. If the cross-sectional area has…

A: Determine the moment of inertia about the x-axis as follows.

Q: Determine the support reaction at C when an axial force of P = 435 kN is applied. The 2014-T6…

A: Find the reaction at C and D.

Q: Select the lightest WT4 shape to be used as a 20 ft long tension member to resist the of dead load,…

Q: A circular-cross-section bar with a diameter of 50 mm and a length of 1.25 m is axially loaded. The…

A: For the above problem we calculate the transitional slenderness ratio whose value decides which…

Q: The linkage is made using two A992 steel rods, each having a circular cross section. If each rod has…

Q: Select the lightest WT4 shape to be used as a 20 ft long tension member to resist the following…

A: Given WT4 shape Length = 20 ft D = 20 k L = 35 k S = 25 k E = 50 k To find Verification of the…

Q: For a rod made of aluminum alloy 2014-T6, select the smallest square cross section that can be used…

A: Given, P = 55 kips = 55 ✕ 1000 psi Length = 20 in The given column is hinged at both ends. So the…

Q: section. If AB is made up of aluminum and CD of steel, determine the required diameter of each…

Q: Problem 2 AW14X30A-36 steel column is pin connected at its ends and has a length of 10ft. Determine…

Q: The W12 * 50 is made of A992 steel and is used as a column that has a length of 20 ft. If its ends…

A: Write the given data: Write the properties of the given material.

Q: The A992 steel W8 * 31 members shown in Fig. is to be used as a pin-connected column. Determine the…

A: Given data: The yield stress, σsy = 50 ksi. Refer the table “American Wide Flange Beams - W Beam”…

Q: Determine the vertical displacement of joint B. Each A992 steel member has a cross-sectional area of…

A: ΔBe = Σ (n N L / A E) ; Member n N L AE -1.667 -0.8333 10 * √(82 + 62) AF 1.667 0.8333 10…

Q: A 6061-T6 aluminum alloy solid circular rod of length 4 m is pinned at both of its ends. If it is…

A: Given data: Length of the circular rod, L = 4 m. Safe axial load acting on the circular rod, P = 15…

Q: Link OB is 20 mm wide and 10 mm thick and is made from low-carbon steel with Sy 200 MPa. The pin…

Q: The A992 steel bar AB has a square cross section. If it is pin connected at its ends, determine the…

A: Given data: The factor of safety with respect to buckling, F.S. = 2, The thickness of steel bar AB,…

Q: Determine the critical buckling stress for a 25' long W12 x 65 steel column. Assume simple pin…

Q: PROBLEM 10.15 12 mm A column with the cross section shown has a 4 m effective length. Using a factor…

Q: Determine the smallest diameter of the rod that will support the load of P = 3.4 kip without…

A: Given data: For the pin jointed beam, the end fixity coefficient is unity.

Q: There is a uniformly distributed load on the beam, which is made of Al2010 (T4) connected to the "A"…

A: As per Bartleby's policy, only the first 3 subparts can be solved please resubmit the next subparts…

Q: The strut is supported by a pin at C and an A-36 stoel guy wire AB. (Eguce.1) Part A If the wire has…

Q: 5. An A-36 (Fy= 250 MPa) steel column has a length of 5 m and is fixed at both ends. If the…

A: Given that, The beam is fixed,Length of beam, L=5 m,Yield stress of beam, σy=250 MPa, Calculate the…

Q: An A992 steel W200 x 46 column of length 9 m is fixed at one end and free at its other end.…

A: Given data: Column specification = A992 steel W200×46 Length of column = 9 m…

Q: The aircraft link is made from an A992 steel rod. Determine the smallest diameter of the rod, to the…

A: Given: Shaft material is A992 steel. Load is 4 kip. Ends are pin connected. E = 29000 ksi

Concept explainers

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.

Question

Determine the largest length of a W10 * 12 structural A992 steel section if it is pin supported and is subjected to an axial load of 28 kip. Use the AISC equations.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Determine the longest length of a W8 * 31 structural A992 steel section if it is pin supported and is subjected to an axial load of 18 kip. Use the AISC equations.
The aircraft link is made from an A992 steel rod. Determine the smallest diameter of the rod, to the nearest 1/16 in., that will support the load of 4 kip without buckling. The ends are pin connected.
The tube is 0.25 in. thick, is made of 2014-T6 aluminum alloy and is pin connected at its ends. Determine the largest axial load it can support.
Question no 1: a)Determine the critical load for its stability if Both ends are fixed.b) For these systems determine the developed stress (It is pin supported, bottom is fixed and the top is pinned;The system is fixed on the bottom ,Both ends are fixed.) The length LB is 14m and material is ANSI1020 where beam is W12 X 87.
The A992 steel W8 * 31 members shown in Fig. is to be used as a pin-connected column. Determine the largest axial load it can support before it either begins to buckle or the steel yields. Take sY = 50 ksi.
A 2014-T6 aluminum alloy column has a length of 6 m and is fixed at one end and pinned at the other. If the cross-sectional area has the dimensions shown, determine the critical load. sY = 250 MPa.
The 10-ft-long bar is made of aluminum alloy 2014-T6. If it is fixed at its bottom and pinned at the top, determine the maximum allowable eccentric load P that can be applied using the formulas in Sec. 13.6 and Eq. 13–30.
For a rod made of aluminum alloy 2014-T6, select the smallest square cross section that can be used if the rod is to carry a 55-kip centric load.
A W12 * 26 structural A992 steel column is pin connected at its ends and has a length L = 11.5 ft. Determine the maximum eccentric load P that can beapplied so the column does not buckle or yield. Compare this value with an axial critical load P applied through the centroid of the column.
The W12 * 50 is made of A992 steel and is used as a column that has a length of 20 ft. If the ends of the column are fixed supported, can the column support the critical load without yielding?
The A992 steel W8 X 31 member shown in Figure is to be used as a pin-connected column. Determine the largest axial load it can support before it either begins to buckle or the steel yields. Take ?? = 50 ksi.
The W360 X 57 column is made of A-36 steel. Determine the critical load if its bottomend is fixed supported and its top is free to move about the strong axis and is pinnedabout the weak axis.