Answered: Determine the magnitude and location of…

Name: Determine the magnitude and location of the equivalent resultantforce
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: Determine the magnitude and location of the equivalent resultantforce acting on the shaft in Fig. 4-49a.240 N/m(60 x)N/mw =FR = 160 NdA = w dx-i = 1.5 m2 m

Engineering

Mechanical Engineering

Determine the magnitude and location of the equivalent resultant force acting on the shaft in Fig. 4-49a. 240 N/m (60 x)N/m W = FR = 160 N dA = w dx - = 1.5 m 2m

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter5: Stresses In Beams (basic Topics)

Section: Chapter Questions

Problem 5.8.1P: The shear stresses t in a rectangular beam arc given by Eq. (5-43): in which Fis the shear force, /...

See similar textbooks

Similar questions

The gate in the figure supported a maximum moment of 180kN-m at the support at a. Determine the maximum height h of water that it supported. The width is 2.0m. The mass of the gate is 1000 kg.
Find the magnitude and location of the resultant force on the cylindrical arc shown in Fig. (10) in each of the following two case: a. Pg=120.11 KPa (abs) b. Pg=90.68 KPa (abs) The arc is 25m long (normal to the paper)
3 include free body diagram
As the electric motor rotates at a constant speed, it applies a torque of 500 Nm to the ABCD shaft. Determine the torsion angle between B and C since G = 27 GPa and the torques shown in the figure are applied to the pulleys B and C.
The shear stresses t in a rectangular beam arc given by Eq. (5-43): in which Fis the shear force, / is the moment of inertia of the cross-sectional area, /lis the height of the beam, and i] is the distance from the neutral axis to the point where the shear stress is being determined (Fig. 5-32). By integrating over the cross-sectional area, show that the resultant of the shear stresses is equal to the shear force V.
3: T = 10.11 kN-m
A steel shaft of diameter 60 mm and length 3.5 m is fixed at its ends A and B. If two torques of the same direction are applied, a 500 N∙m torque at C (1m m from the left end) and a 200 N∙m torque at D (1m from the right end), determine the maximum internal torque in the shaft. 4.72 MPa 9.77 MPa 6.74 MPa 11.79 MPa
If the width of the wedge used in the 3 cm diameter shaft, which transmits the motion received from the 34 - 3 HP motor at 400 rpm, is 8 mm and the length is 24 mm, what is the shear stress acting on this wedge?A) 186.5 daN / cm2B) 193.9 daN / cm2C) 93.25 daN / cm2D) 139.9 daN / cn2E) 168.5 daN / cm2
Which of the following has the dimension for density. M1 L1 T-2 M-1 L1 T 2 M1L-3 M L -1 T-2
ANSWER THE FIFTH PROBLEM ONLY
The inner diameter of the AB compressed air tank is 160mm, the wall thickness is 1mm.Since the manometer pressure in the tank is 1,6MPa ,at point a at the top of the tank maximum normal stress and determine the maximum plane shear stress.(c=16mm , d=38mm, e =32mm, g=160mm, h=1mm, k =1.6MPa , F=160N)
The three-bar truss in Fig. a is subjected to a horizontal force of 5 kip. If the cross-sectional area of each member is 0.20 in2, determine the horizontal displacement at point B. E = 29(103) ksi.