Determine the magnitude of the moment of the force about the x axis. The lug nut on the wheel of the automobile is to be removed using the wrench and applying the vertical force of F = 30 N at A. (Figure 1) Express your answer to three significant figures and include the appropriate units. Figure 1 of 1 M, = Value Units F = 30 N Submit Request Answer 0.25 m Part B 0.3 m 0.5 m Determine if this force is adequate, provided 14 N · m of torque about the x axis is initially required to turn the nut. .0.1 m O no O yes

Determine the magnitude of the moment of the force about the x axis. The lug nut on the wheel of the automobile is to be removed using the wrench and applying the vertical force of F = 30 N at A. (Figure 1) Express your answer to three significant figures and include the appropriate units. Figure 1 of 1 M, = Value Units F = 30 N Submit Request Answer 0.25 m Part B 0.3 m 0.5 m Determine if this force is adequate, provided 14 N · m of torque about the x axis is initially required to turn the nut. .0.1 m O no O yes

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.75P: The single-plate clutch transmits the torque C from the input shaft on the left to the output shaft...

See similar textbooks

Similar questions

Determine the magnitude of moment (Nm) of the 383-N force about point A if x = 0.55 m , y = 0.69 m, and θ = 41.4ᵒ. Round off only on the final answer expressed in 3 decimals. Instead of units, type either POSITIVE or NEGATIVE to indicate the direction of moment which is consistent with the sign convention discussed on lectures. Sample answers are 12.908 POSITIVE or 12.908 NEGATIVE
Take that w0 = 4.6 kN/m. Replace the loading by an equivalent force. Express your answer to three significant figures and include the appropriate units. Enter positive value if the force is upward and negative value if the force is downward. Replace the loading by a couple moment acting at point O. Include clockwise or counterclockwise.
Determine the algebraic sum of the moments of forces relative to a point in F = 10.0 N; m =9.0 Nm, q =8.0 N/m
Solve Prob. 7.29 if =0.
The single-plate clutch transmits the torque C from the input shaft on the left to the output shaft on the right. Compression springs between the clutch housing and the pressure plate provide the necessary pressure on the friction surface. The splines prevent the clutch plate from rotating relative to the output shaft. If Ri=4 in. and R0=9 in., determine the total force that must be applied to the pressure plate by the springs if the clutch is to transmit a torque of C=56lbft when it is new.
Calculate all forces acting on the bar AB described in Prob. 5.1.
Select F1=108 and F2=112 on the train bridge in the figure. Find the force on the bar BC and whether it is the pull.
The motorcycle weighs 151 kg and the driver weighs 64 kg. Dimensions l1 = 0,31 m ja l2 = 0,23 m Determine the support force on the rear tire.
FINDING MAXUMIM AND MINIMUM MOMENT My question goes about the problem which is located here: https://www.bartleby.com/questions-and-answers/the-70-n-force-acts-on-the-end-of-the-pipe-at-b.-determine-the-angles8-0-180-of-the-force-that-will-/567dba2e-b426-4c49-967a-56130cc9db87 In the second step, it states that the value of the equation (1) will be maximum when the first derivative of the moment equation will be zero. Why? And why did we use the derivative rules in the first place? Thank you in advance for your patience,
For the spring assemblage shown below, determine the displacement at node 2 and the forces in each spring element. Also determine the force F3. Given: Node 3 displaces an amount 8 = 12.5 mm in the positive x direction because of the force F3 and k1 k2 175 kN/m.
The shaft is supported at its ends by two bearings AA and BB and is subjected to the forces applied to the pulleys fixed to the shaft. (Figure 1) The T1=T1= 585-NN forces act in the -zz direction and the 200-NN and 80-NN forces act in the +yy direction. The journal bearings at AA and BB exert only yy and zz components of force on the shaft. Part A Determine the resultant normal force on the cross section at CC. Express your answer to three significant figures and include appropriate units. NC= values ? NC= units? Determine the resultant shear force in the yy direction on the cross section at CC . Express your answer to three significant figures and include appropriate units. (VC)y Values ? (VC)y units ?
Determine the magnitude of the pin force at A.Assume W = 755 lb, a = 5.4 ft, b = 3.9 ft, r = 7 in.