Answered: Determine the magnitude of the moment…

Determine the magnitude of the moment of the force F about the base line AB of the tripod. a 4.9m b=0.5m i= 50 N J= -20 N K=-75 N

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter6: Beams And Cables

Section: Chapter Questions

Problem 6.18P: For the ladder in Prob. 6.17, find the internal force system acting on section 2, assuming that x <...

See similar textbooks

Related questions

Q: A 10-kg block slides down a smooth inclined surface as shown in the figure below. Determine the…

A: Given data:- Mass of block =10-kg gap between the block and the surface=0.1-mm the area of the block…

Q: 2. Heavy fuel oil flows from A to B through a 1000-m steel pipe. The horizontal 150-mm-diameter…

Q: Problem9 The entrance flow between two parallel plates (gap h) has a velocity that varies linearly…

A: In a laminar flow between two parallel plates, the velocity profile is symmetric about the mid-plane…

Q: To test a glue, two plates are glued together as shown in Fig. 3.16. The bar formed by the joined…

Q: using excel how can we convert these two 9.81 m/s2 to ft/s2 i. 2000 kg/m3 to lbm/ft3

A: Unit conversion can be done in excel using the CONVERT function. This function is very helpful in…

Q: glass with an area of 0.625 m² is fit in the wooden outside wall of a room. The dimension of wall is…

A: Given:Area of the glass window, Ag=0.625 m2wall dimension=25×3.05 m2thermal conductivity of wood,…

Q: A 4-m high and 6-m-wide wall consists of long 15-cm x 20 cm cross section horizontal bricks (k of…

A: To Find: The heat transfer rate through the wall.

Q: in regard to thrust-producing engines, what is the dilemma between performance versus efficiency,…

Q: Calculate the largest weight W that can be supported by two wires. The stress in either wire is not…

A: Givenσ=7.6 MPaAAB=150 mm2AAC=250 mm2

Q: Consider a w-N weight suspended by two wires as shown in the accompanying figure. If the magnitude…

A: According to the question F2=80N we need to find Force (F1) Weight(W)

Q: The stress-strain diagram for a steel alloy having an original diameter of 0.3 in. and a gage length…

A: To find: (a) The modulus of resilience. (b) The modulus of toughness. Given: The original diameter…

Q: A solid piece of metal of volume 10,000 mm3 is compressed by a pressure of 70 MPa. Determine the…

Q: What are the types of liquid fuels? 2. Why density is important to liquid fuels? 3. What are the…

A: 1.Liquid Fuels: Liquid fuels are the type of fuels which are in liquid form in nature and they can…

Q: A locomotive is traveling on the straight and level track with a speed v = 79 km/h and a…

A: Given that: speed of the locomotive is 79 km/h deceleration is 0.6 m/s2 when θ = 64o, r = 375 m, it…

Q: 3 100kN 100KN B VFL Ft o find the supports' reactions at Ay..... Dy.... 2) Find the normal force in…

A: Given data, To find: Ay, Dy, FFE, FBC, and FHG

Q: Part of a control linkage for an airplane consists of a rigid member CB and a flexible cable AB.…

A: The given information in the problem is shown in the following attached image:

Q: suppose that F1=4kN. a) Determine the magnitude of the resiltant force FR=F1+F2. b) Determine…

A: In this problem, we will calculate the magnitude of the resultant force by taking two different…

Q: Problem 5: Inputs: F = 81 i lb The force is applied at point A. (a) Use the cross product to compute…

Q: The launching catapult of the aircraft carrier gives the jet fighter a constant acceleration of 59…

A: Given the acceleration and carrier speed. Required: Velocity.

Q: A 200 x 100 x 50 mm steel block is subjected to a 15 MPa. The Young's modulus and Poisson's ratio of…

A: Given:Dimension of steel block=200×100×50 mmHydrostatic pressure=15 MPaE=200 GPaϑ=0.3Find,Change in…

Q: Carnot cycle heat pump utilizes R-134a as the working fluid. Heat is transferred from the fluid at…

A: Given:Refrigerant=R134aCondenser temperature, Tc=100oFEvaporator temperature, Te=20oFFind:a…

Q: Why is it better to use an automatic system rather than a manual one?

A: Manual System: A manual system is a system where records are maintained by hand without the aid of a…

Q: The new line of go-karts will have a two-stroke internal combustion engine. The engine generates 35…

A: Given: Power = 35 hp = 26.0995 kW Mean speed = 2000 rpm To find: Design a flywheel

Q: A Carnot refrigerator has working temperatures of -30°C and 35°C. If it operates with Refrigerant…

A: The answer is given below,

Q: A steel rod (k = 50 W/m K) of length 50 cm and diameter 10 mm is placed in such that one of its end…

Q: n the given figure below what is the normal and shear stresses in MPa at point P

A: Given:Force applied at corner, F=600 NDiameter of pipe, d=30 mm

Q: Question No #06: Analyze the telescoping link AB at the instant represent and determine its angular…

Q: Mohr's circle, invented by Christian Otto Mohr, is a graphical representation of the transformation…

Q: The aircraft A with radar detection equipment is flying horizontally at an altitude of 12.2 km and…

Q: enturimeter of 0.5 contraction ratio has been fixed in a 100 mm diameter horizontal pipe.The head of…

A: Given:d=100 mmcontraction ratio=0.5No flow pressure head=P1ρg=3 m +10.3 m=13.3 mthroat pressure…

Q: Figure 5-51/52 Full Alternative Text 5-53. The 50-mm-diameter A992 steel shaft is subjected to the…

Q: Two plates are positioned at distance of 1.3 mm from each other. One of the plates is moving at…

Q: Determine the moment of inertia of the cross-sectional area of the reinforced channel about the…

Q: CONSIDER A 210-MW STEAM POWER PLANT THAT OPERATES ON A SIMPLE IDEAL RANKINE CYCLE. STEAM ENTERS THE…

Q: A 200-kg dragster (racing car) exerts a constant force of 4000 N during a race. The coefficient of…

A: As per the guidelines we are subjected to solve only three subparts of a question. Please repost the…

Q: A girl operates a radio-controlled model car in a vacant parking lot. The girl's position is at the…

Q: Find the missing properties and give the phase of the substance. (a) H2O s = 1.75 Btu/lbm R, P = 4…

Q: escribe with the aid of diagrams the operational sequence of four stroke spark ignition and four…

A: According to the question we need to explain four-stroke spark ignition engine and Four-stroke…

Q: Determine the magnitude of the resultant internal normal force, shear force and bending moment on…

Q: The fuel economy of a car (miles per gallon) varies with its speed. In an experiment, the following…

A: Given: To find: Fuel economy at speed of a) 30 mph b) 65 mph

Q: 9. A certain ideal gas whose R = 278.6 1/kgm.K and C₂ = 1.015 kJ/kgm.K expands isentropically from…

A: GivenR=278.6 J/kgKCp=1.015 kJ/kgK=1015 J/kgKPVy=ConstantP1=1517 kPaT1=288oC=288+273=561KP2=965…

Q: Problem: Write the transfer function of the systems: G₁(s)= Y(s) U(s) m X k 日 b X(s) U(s) G₂(s)=- M…

A: The displacement of the block m is x. The displacement of block M is y. The transfer function is the…

Q: Motor torque, Tm I'm DC motor, J₁ Viscous friction, b₁ Gear train Load torque, TL Load, √₂ Viscous…

A: Free body diagram of load J1:

Q: Determine the magnitude of the vertical force A, for the cantilever beam, where w = 14 kN/m, M=131…

Q: rod of length L having uniform cross-sectional area A is subjected to a tensile force P . If the…

A: Given: A rod of length L having uniform cross-sectional area A is subjected to a tensile force P…

Q: RC-2 A half ring of charge lies in the x-z plane with its center at the origin as shown to the…

Q: A fin losses 6 W heat. The effectiveness and efficiency of the fin are 3 and 0.75 respectively.…

Q: then rounding-off to 5 decimal places yields 1.23457 and that is the value which you need to type in…

A: Given: Horizontal force→P=2600 lb Cross sectional area of the truss→A=2 in2=0.013 ft2 Youngs…

Q: 11.93 Engineers are examining how shock absorber designs affect the displacement of a mountain…

A: For the solution refer below images.

Q: can you show me the steps on how you were able to obtain the coordinate direction angles?

Concept explainers

Die Stock

Die stock is expressed as the type of component which is utilized for fitting purposes while creating or shaping uniform threads on tubes, pipes, or screws. The die stock (die handle) has three screws around the adjustable part of a particular machine that helps to locate the die. Also, die stock can endure on a variety of hex and split adjustable dies of several dimensions. One of the primary reasons for using die stock in industries is because die stock can be operated by hands. Commonly, it is made up of high carbon steel.

Question

Problem Statement
Based on Problem 4-61 from the textbook.
Determine the magnitude of the moment of
the force F about the base line AB of the
tripod. a
a=4.9m
b=0.5m
i= 50 N
J= -20 N
Unique Values for Each Student:
K=-75 N
1.5 m
X
2 m
2 m
b
D
B
Z
1 m
a
A-
2.5 m
y

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

For the ladder in Prob. 6.17, find the internal force system acting on section 2, assuming that x < a/2.
A cargo ship is tied down to marine boll arts at a number of points along its length while its cargo is unloaded by a container handling crane. Each bollard is fastened to the wharf using anchor bolts. Three cables having known tension force magnitudes F, = ll0 kN.F, = 85kN.and F, 9OkNare secured to one bollard at a point A with coordinates (0.0.45 m. 0) in the x-r-: coordinate system shown in the figure part b. Each cable force is directed at an attachment point on the ship. Force F, is directed from point A to a point on the ship having coordinates (3 m, 9 m. 0) force F, is directed at a point with coordinates (6.5 m. 8.5 m. 2 m) and force F, is directed at a point with coordinates (8 m. 9 m. S m). The diameter of each anchor bolts is 4 24 mm. (a) Find the reaction forces and reaction moments at the base of the bollard. (b) Calculate the average shear stress in the anchor bolts (in the x-: plane). Assume each bolt cart ics an equal share of the total force.
PROBLEM 4: The boom OC is subjected to tension forces at A and C. It is known that the tension in A is 26 kN and at C is 12 kN. Unit vector CE. (ANSWER: -0.38i-0.87j+0.32k) Tension at A. (ANSWER: 13.20i-15.8j+15.8k kN VECTOR COMPONENT FORM) Moment about O due to the given forces. (ANSWER: 78.71i+0j+3.2k kN VECTOR COMPONENT FORM)
A force F1= 2i – 6k {kN) is applied at the position 3j + 5k {m}, meanwhile another force F2 = - i + 4j + 7k {kN) is applied at the position 8k {m}, on a structure. Evaluate the resultant moment by vector calculation
Given the figure, answer the following multiple choice questions1) Which of the following best approximates the moment of force P about point B? A. 33.6 kN-m CW B. 44.8 kN-m CW C. 56 kN-m CW D. 156.8 kN-m CW2) Which of the following force-couple sets applied at point A is equivalent to the loadings acting on bent bar ABC? A. FA = 2kN down; CA = 19.8 kN-m CW B. FA = 8kN down; CA = 92.2 kN-m CCW C. FA = 2kN down; CA = 61.8 kN-m CW D. FA = 8kN down; CA = 156.8 kN-m CW
An L-shaped bracket is supported by a frictionless pin at A and a cable between points B and D. If pin A is the origin, point C is at (-7, 0); and pin B is at (-7, -10). The cable is attached between point B and an anchor at point D, at (-2, -14). Units are in feet. Force F acts at point C at an angle of 60o from the positive x-axis. Determine the magnitude of the moment that the force F produces about point A. Determine the tension required to hold the bracket in position.
Expiremental Method: Force Table F1 - 150N, 30° N of E F2 - 100N, 60° E of S 1) Find the Equilibrant Magnitude and Equilibrant Direction 2) Find Resultant Force Vector Magnitude and %Error 3) Find Resultant Force Vector Direction and %Error
Which of the following gives the moment MD about point D of the tensile force TBA exerted by the wire at point B? Note that rB/D = (4i - 6k) m and TBA = (-8i + 6j + 4k) kN and that MD = rB/D x TBA. a. (36.0i + 32.0j + 24.0k) kN-mb. (48.0i + 24.0j + 16.0k) kN-mc. (-36.0i - 32.0j - 24.0k) kN-md. (16.0i - 12.0j -8.0k) kN-m
a = 4 mb = 3.2 mc = 2 mF = {-7i+4j+12k} NSpecified axis: AF Find the magnitude of the moment of F about the specified axis.If the calculated answer is not whole number, express it in 4 significant figures.
1. R is the resultant coplanar-concurrent forces composing of P, T, F, and each Q acting on a body. Find the magnitude of the fourth force Q and its angle with respect to horizontal, if P = 840N directed downward to the left at 20 degrees with the vertical, T = 890N is acting to the right along the horizontal, F = 530N is up to the right at 45 degrees with the horizontal and R = 1300N acting downward to the right 30 degrees with the horizontal. show solution, formula and the sketch of the FBD and pls write legible
1. R is the resultant coplanar-concurrent forces composing of P, T, F, and each Q acting on a body. Find the magnitude of the fourth force Q and its angle with respect to horizontal, if P = 840N directed downward to the left at 20 degrees with the vertical, T = 890N is acting to the right along the horizontal, F = 530N is up to the right at 45 degrees with the horizontal and R = 1300N acting downward to the right 30 degrees with the horizontal.
R is the resultant coplanar-concurrent forces composing of P, T, F, and each Q acting on a body. Find the magnitude of the fourth force Q and its angle with respect to horizontal, if P = 840N directed downward to the left at 20 degrees with the vertical, T = 890N is acting to the right along the horizontal, F = 530N is up to the right at 45 degrees with the horizontal and R = 1300N acting downward to the right 30 degrees with the horizontal. Show your answers in graphucal and analytical method