Determine the magnitude of the resultant force. Replace the three forces acting on the shaft by a single resultant force. Suppose that F = 650 lb , F2 = 400 lb , and F3 = 260 lb . (Figure 1) Express your answer to three significant figures and include the appropriate units. ? µA FR = Value Units Submit Request Answer Part B Figure < 1 of 1 Determine the angle between the resultant force and the x axis. Express your answer using three significant figures. vec 5t 3 ft - 2 ft -- 4 ft °, measured counterclockwise from the negative x axis 12 Submit Request Answer Part C Specify where the force acts, measured from end B.

Determine the magnitude of the resultant force. Replace the three forces acting on the shaft by a single resultant force. Suppose that F = 650 lb , F2 = 400 lb , and F3 = 260 lb . (Figure 1) Express your answer to three significant figures and include the appropriate units. ? µA FR = Value Units Submit Request Answer Part B Figure < 1 of 1 Determine the angle between the resultant force and the x axis. Express your answer using three significant figures. vec 5t 3 ft - 2 ft -- 4 ft °, measured counterclockwise from the negative x axis 12 Submit Request Answer Part C Specify where the force acts, measured from end B.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter6: Beams And Cables

Section: Chapter Questions

Problem 6.15P: The structure is supported by a pin at C and a cable attached to A. The cable runs over the small...

See similar textbooks

Similar questions

Determine the magnitude(lb) of the vertical component of force at point C if P = 127 lb, x= 13.9 in, y = 8.7 in, and z = 8.2 in. Round off only on the final answer expressed in 3 decimal places. Instead of units, indicate the direction: use U if upward and D if downward
The shaft is supported at its ends by two bearings AA and BB and is subjected to the forces applied to the pulleys fixed to the shaft. (Figure 1) The T1=T1= 585-NN forces act in the -zz direction and the 200-NN and 80-NN forces act in the +yy direction. The journal bearings at AA and BB exert only yy and zz components of force on the shaft. Part A Determine the resultant normal force on the cross section at CC. Express your answer to three significant figures and include appropriate units. NC= values ? NC= units? Determine the resultant shear force in the yy direction on the cross section at CC . Express your answer to three significant figures and include appropriate units. (VC)y Values ? (VC)y units ?
If the component of a force along x-axis is Fx = 20 kN and along y-axis is Fy = 30 kN, and if “t” is an axis making an angle of 30o in the clockwise direction with respect to x-axis, what would be the components of this force Ft and Fn along the orthogonal axes “t” and “n”, respectively? Select one: Ft = 32.32 kN and Fn =15.98 kN Ft = 2.32 kN and Fn = 35.98 kN Ft = 15.98 kN and Fn = 32.2 kN Ft = 35.98 kN and Fn = 2.32 kN
If the component of a force along x-axis is Fx = 20 kN and along y-axis is Fy = 30 kN, and if “t” is an axis making an angle of 30o in the counter clockwise direction with respect to x-axis, what would be the components of this force Ft and Fn along the orthogonal axes “t” and “n”, respectively? Select one: Ft = 2.32 kN and Fn = 35.98 kN Ft = 15.98 kN and Fn = 32.32 kN Ft = 35.98 kN and Fn = 2.32 kN Ft = 32.32 kN and Fn =15.98 kN
Two forces X and Y act vertically downward directly at points D and F respectively while force Z acts at point B as shown. Determine the magnitude (N) of the force in member GF if X=651N, Y=232N, Z=134, a=5.7m and b=3.2m. Round off only on the final answer expressed in 3 decimal places. Instead of units, indicate C if force is compressive or T if tensile.
Draw the correct Free Body Diagram (FBD). Solve the Resultant Force at A. Given F1= 50lb and F2= 80lb.
The cantilevered rack is used to support each end of a smooth pipe that has a total weight of 460 lblb as shown in (Figure 1). Determine the magnitude of the normal force that acts in the arm at its fixed support A� along a vertical section. Determine the magnitude of the shear force that acts in the arm at its fixed support A� along a vertical section. Determine the magnitude of the moment that acts in the arm at its fixed support A� along a vertical section.
Don't Copy ,I need Correct Handwritten Solution Only Asap (Including FBD) 1)The support at O can hold a maximum of 1000 N-m magnitude moment. Determine the maximum possible force F. Express F in Newtons and use three significant figures. The direction of F is unknown.
The forklift supports the engine. Determine the force that this load generates on element FB. Write your answer in Newtons. Consider Engine mass = 148 kg a = 1.47 m b = 2.21 m
Resolve the forces shown in the Figure below to two components Fx and Fy
1. F1 and F2 forces AB in the system whose loading condition is given in Figure The tensile force in the chain is in balance with the Fab. of force F2 Calculate the magnitude and cosine directives. F1(N)=60 Fab(N)=100 a(°)=20 b(°)=50
Determine the Resultant Force, its magnitude and direction of the given co-planar, Space tensile force cables as shown in the diagram below. AB = 100lbs; AC = 80 Ibs & AD= 90 Ibs. Please answer in COMPLETE solution. *3 decimal places all answer.