Determine the maximum value of weight W which may be applied without causing the 8o N block to slip. The coefficient of static friction between the block and the plane is us = 0.2, and between the rope and the drum D µ', = 0.3. O A) T(1) = 80*cos (37)*(0.2) T. D '1 T. 2 B) T(2)T(1) Which following one is TRUE?

Determine the maximum value of weight W which may be applied without causing the 8o N block to slip. The coefficient of static friction between the block and the plane is us = 0.2, and between the rope and the drum D µ', = 0.3. O A) T(1) = 80cos (37)(0.2) T. D '1 T. 2 B) T(2)T(1) Which following one is TRUE?

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.4P: The two homogeneous bars AB and BC are connected with a pin at B and placed between rough vertical...

See similar textbooks

Similar questions

The square-threaded screw 0f the C-clamp has a mean diameter of 8 mm and a pitch of 1.6 mm. The coefficient of static friction between the threads is 0.2. If the torque C=1.50Nm is used to tighten the clamp, determine (a) the clamping force; and (b) the torque required to loosen the clamp.
roll of paper has a uniform weight of 2kN and is suspended from the wire hanger so that it rests against the wall. If the hanger has a negligible weight and the bearing at O can be considered frictionless, determine the force P needed to start turning the roll if = 30°. The coefficient of static friction between the wall ܬܐ and the paper is µ = 0.3.
The block brake consists of a pin-connected lever and friction block at B. The coefficient of static friction between the wheel and the lever is μs = 0.3, and a torque of 5 N ⋅m is applied to the wheel. Determine if the brake can hold the wheel stationary when the force applied to the lever is (a) P = 30 N, (b) P = 70 N Draw the free-body diagram of the lever.
A load G1 is placed on the horizontal plane. A rope is attached to it, which is passed over a stationary pulley, and a load of weight G2 is attached to the other end of the rope. Determine the equilibrium position of the load G1 (length x) if the height x and the coefficient of friction µ are known.Note: The answer is x=h\tan alpha i want to understdan how this problem is fixed.
Two hemispheres having an inner radius of 2 ft and wall thickness of 0.25 in. are fitted together, and the inside pressure is reduced to -10 psi. If the coefficient of static friction is ms = 0.5 between the hemispheres, determine (a) the torque T needed to initiate the rotation of the top hemisphere relative to the bottom one, (b) the vertical force needed to pull the top hemisphere off the bottom one, and (c) the horizontal force needed to slide the top hemisphere off the bottom one.
The block brake is used to prevent the wheel from rotating when it is subjected to a torque moment M0. If the coefficient of static friction between the wheel and the block is us, determine the minimum force P that must be applied.
The movable bracket shown may be placed at any height on the 3-in.-diameter pipe. If the coefficient of static friction between the pipe andbracket is 0.25, determine the minimum distance x at which the load Wcan be supported. Neglect the weight of the bracket.
The truck has a mass of 1.25 Mg and a center of mass at G. The coefficient of static friction between the wheels and the ground is Uw = 0.5, and between the crate and the ground, it is uc = 0.4. Determine = = the greatest load it can move if (a) the truck has rear-wheel drive while the front wheels are free to roll. (b) the truck has four-wheel drive.
The homogenous 360 kg block rests against the vertical wall, for which the coefficiewnt of friction is 0.25. A force P is applied to the midpoint of the right face in the direction shown in thre figure. What range of values may P have without disturbing equilibrium. Give solution. (Ans. 5260 N < P < 7890 N)
A worker is pulling down the rope as shown.If the pulleys in the system are frictionless, andthe coefficient of static friction between thecrate and the floor is ?? = 0.3, determine thesmallest force the worker must exert on therope in order to move the 100 kg crate, and theangle ? at this moment.
A small block of weight W is placed on a plane inclined at an angle θ to the horizontalThe coefficient of friction between the block and the plane is μi) When θ is 20O the block is in limiting equilibrium. Find μii) When μ = 1/3 and is 30o a horizontal force of 6N is required to prevent theblock from slipping down the plane. What is the weight of this block?iii) A force of 10N up the pane causes the bock to be on the point of sliding up If W = 20N and μ is ¼, find θiv) If θ is 40o and μ is 0.5 find the magnitude and direction of the least force required to prevent the block from sliding down the plane when W = 12N
the 31mm diameter screw has a double square theread with pitch of 6 mm and a lead of 12 mm .the screw and it's mating threads in the fixed block are graphite- lubricated and have a friction coefficient of 0.09. M=51N.m is applied to the right-hand portion of the shaft , determine (a) the force P required to advance the shaft to the right (b) the force P which would allow the shaft to move to the left at constant speed