Determine the normal stress in members BD, AC, and BC in the truss shown. The cross- sectional area of each member is 1500 mm². Indicate whether the stresses are tensile (T) or compressive (C). Use 2 decimal places in every solved value. 10 т 10 m 10 m K L 6 т G H 6 m 15° 15° 50 kN 40 kN E F 6 т D 6 m A

Determine the normal stress in members BD, AC, and BC in the truss shown. The cross- sectional area of each member is 1500 mm². Indicate whether the stresses are tensile (T) or compressive (C). Use 2 decimal places in every solved value. 10 т 10 m 10 m K L 6 т G H 6 m 15° 15° 50 kN 40 kN E F 6 т D 6 m A

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Rigid bar ABC shown in the figure is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 5 mm, and it is supported by double-shear pin connections at B and D. The pin at bracket A is a single-shear connection. All pins are 6 mm in diameter. Assume a = 600 mm, b = 250 mm, h = 425 mm, P = 900 N, and θ = 55°. Determine the the shear stress in pin B. Express your answer in MPa rounded to the nearest hundredths.
The plate as shown weighing 25kN is raised by a cable sling. The cable sling has the identical clevis at each end and the pins through these clevises are 20mm Ø. Determine the shear stress in the pin. Compute the bearing stress between the clevis and thepin if the thickness of the yoke is 25mm.Use 2 decimal places in every solved value.
Three steel rods, each having a cross-sectional area of 500 mm2, are assembled in a symmetrical manner, ass shown in the igure. Assume that steek behaves as a linear elastic material with E= 200 GPa. Determine the deflection of joint A due to a downward force of P= 2MN
The rigid bar BDE is supported by two links AB and CD. Link AB is made of aluminum (E = 70 GPa) and has a cross-sectional area of 519 mm2; link CE is made of steel (E = 200 GPa) and has a cross-sectional area of 633 mm2. For the 36 kN force shown, determine the deflection of B (mm) *deflection should have a negative sign if compression and positive if tension. Also, your final answer should have two decimal places
For the frame shown, determine the maximum normal stresses (compression and tension) and the maximum shear stress, caused by the acting trapezoidal load. Express your answer in MPa. Sección trasversal means cross section.
please sir solve accurate and fast. ( of possible solve compyuterised) THANKS a 30m weighing 0.900kg has a cross-sectional area 0.0485cm^2. the tape measures 30.000m when supported throughout under a tension of 5kg. the modulus of elasticity is 2.1x10^6kg/cm. what tension is required to make the tape measure 30m when supposed only at the two ends?
Determine the slope at the left support A (in degrees.). The beam is loaded with a moment load M = 15 kN-m at its midspan. EI is constant and equal to 36,159 kN-m^2. Use length of beam L = 8 m. ROUND OFF TO FIVE DECIMAL PLACES. USE STORED VALUES.
If P = 8.571 kN, determine the stress in member CE assuming that the area in steel is 24 mm^2. *DRAW THE FREE BODY DIAGRAM *COMPLETE SOLUTION *3 decimal places ALL ANSWER
Solve the following problems completely and neatly. Use 3 decimal places in all your computations except for strain and rho(5 decimal places). Input your answer in the text box provided in each number. Calculate the stress in the steel of the section in PART B in MPa.0
A square bar carries a series of loads as shown in Figure P1-47. Compute the stress in each segment of the bar. All loads act along the central axis of 1-47. the bar.
A square bar carries the series of loads as shown. Compute the load (kN) and stress (MPa) in each segment of the bar. Determine whether the load or stresses are tension (T) or compression (C). All loads act along the central axis of the bar.
1. The bar ABCD consists of 3 cylindrical steel segments with different lengths and cross-sectional areas. Axial loads are applied as shown. Calculate the normal stress in each segment in psi unit. Indicate if T or C.Calculate the total axial deformation in Problem #1 if Es = 29 x 10 6 psi . Indicate if the bar elongates or contracts.