Determine the Nyquist rate of a signal whose frequency spectrum is given by x(f) = r(f) – r(f – 1000) + r(f – 3000) – 2r(f – 4000) + r(f – 6000), where r(f) is the unit ramp function in the frequency domain. O a. 3 kHz O b. 8 kHz O c. 16 kHz O d. 6 kHz O e. 4 kHz Of. 12 kHz

Determine the Nyquist rate of a signal whose frequency spectrum is given by x(f) = r(f) – r(f – 1000) + r(f – 3000) – 2r(f – 4000) + r(f – 6000), where r(f) is the unit ramp function in the frequency domain. O a. 3 kHz O b. 8 kHz O c. 16 kHz O d. 6 kHz O e. 4 kHz Of. 12 kHz

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q 2 : An audio signal given by 15 sin( 000 pi t)+20 sin(8000 pi t) amplitude modulated DSB-FC) a sinusoidal carrier wave 60 sin(100,000 ) a. Derive an expression for the modulated signal. b. Find the modulation index. c. Find the spectrum of the modulated signal. d. Sketch the spectrum of the modulated signal e. Which type of demodulation method you propose to reconstruct the audio at receiver. Why? Q 2 : A modulating signal is used to modulate a carrier signal(AM modulation). Let P T . P c ,P SB . P USB , P LSB and u are the total power, carrier power, side band power, upper side band power, lower side band power and modulation index respectively, Prove the following: a. P c =P T ( 2 2+m^ 2 ) b. P SB =P T ( m^ 2 2+m^ 2 ) c. P USB =P LSB = 1 2 ( m^ 2 2+m^ 2 )P T
An FM radio broadcast used a modulator with a frequency deviation sensitivity of 5KHz/V, a 2Vp – 10 kHz modulating signal, and a 10Vp – 88MHz carrier Signal , determine : (a) Actual minimum bandwidth from the Bessel function table in kHz (b) Appropriate minimum bandwidth using Carson’s rule in kHz (c) Percent Modulation (d) The FM modulated waveform carrier and significant sideband components amplitudes; NOTE: Use this format in providing your answers to this problem: VJ0=x.xx v,VJ1=x.xx v,VJn=x.xx v; where VJO is the modulated carrier amplitude, VJ1-VJn is the amplitudes in significant sideband components and the number of sidebands (n) depending on your computation. (e) The unmodulated carrier power (W) for the FM modulator assumes that the load resistance is 50 Ω f) The corresponding FM modulated waveform carrier and significant sideband components power and its total power in mW. Note: Use this format in providing your answers to this problem: PJ0=xxx.xx mW,PJ1=xxx.xx…
help please with explain A narrowband FM signal has a carrier frequency of 110 kHz and a deviation ratio of 0.05. The modulation bandwidth (signal bandwidth) is 10 kHz. This signal is used to generate a wideband FM signal with a deviation ratio of 18 and a carrier frequency of 98 MHz. a) Give the required value of frequency multiplication, n. b) Give two frequencies for the mixer to give the desired carrier. c) Define the required bandpass filter (center frequency and bandwidth).
1. The CT signal x(t)=3cos (600πt) + 6cos2(mπt) is critically sampled (Nyquist rate) by fs=4000 Hz. Find:i. The value of m.ii. The frequency components of the signal.iii. The frequency resolution (∆f) of the output spectrum if the sampled signal is processed by 64 point-DFT.iv. Define frequency resolution.
1. The CT signal x(t)=3cos (600πt) + 6cos2 (mπt) is critically sampled (Nyquist rate)by fs=4000 Hz. Find:i. The value of m.ii. The frequency components of the signal.iii. The frequency resolution (Δf) of the output spectrum if the sampled signal isprocessed by 64 point-DFT.iv. Define frequency resolution.
1. Given an analog signal x(t)=10 cos(2π.5500t)+5 cos(2π.7500t) is sampled at a rate of 8,000 Hz, a. Sketch the spectrum of the sampled signal up to 20 kHz; b. Sketch the recovered analog signal spectrum if an ideal low pass filter with a cutoff Frequency of 4 kHz is used to filter the sampled signal in order to recover the original signal; c. determine the frequency/frequencies of aliasing noise.
Consider the following amplitude modulated signals(t)= cos(2000t) 4cos(2400t) cos(2800t). If this signal is sampled, then what will be Nyquist's sampling frequency of this signal s(t)?
A robotic system with transfer function ?(?) =(100)/(s(0.1s+1)(0.1s +1)) is controlled with gain K as shown in the figure. A)To analyze the frequency response of this system, draw the Nyquist graph. B)Apply the Nyquist stability criterion. C)Verify the stability analysis you made in part (b) by plotting root locus plots for the positive and negative values of the K gain. D)Calculate the gain value that makes this system borderline stable and show it on Nyquist and Root locus graphs. E)Calculate the gain margin, phase margin, gain crossover frequency and phase crossover frequency values. F)Explain whether the system is stable over the gain margin and phase margin values. WE NEED TO SOLVE THE PROBLEM IMMEDIATELY. PLEASE HELP.
An Armstrong modulator is used to generate FM which is suitable for FM broadcasting.You are given input of narrowband FM signal with carrier frequency fc1 = 27 MHz anda frequency deviation Δf1= 17 kHz. Assume that the frequency multiplier with n = 3 andlocal oscillator frequency of 80 MHz. Calculate the output of the carrier frequency andfrequency deviation if additive frequency is selected by mixer. Explain your obtainedanswer.
1- Explain the principle of direct method generation of FM signal.2- What is the difference between narrowband FM and wideband FM refer tothe spectral component of the two signals.3- Compare the S/N ratio of:a) AM DSB-LCb) AM SSB-SCc) FM4- Explain the operation of frequency demodulation by using the PLL method.5- Explain what Carson's rule is.
Explain the role played by Fourier's theory, with a special reference to Fourier synthesis and Four analysis
An analog signal is given as x(t) = 5 + 2 cos(20πt) + 3cos(400 πt). a) What is the bandwidth of x(t)? Determine the Nyquist sampling frequency for x(t), both in radian/sec (ws), and in Hz (Fs).b) Formulate Xp (jw), the signal sampled with the Nyquist frequency. c) Plot frequency spectrum of the the sampled signal, Xp (jw). d) Determine the filter to reconstruct the signal x(t). e) Is it possible to reconstruct the signal x(t) for Ts =0.004 [s]? State that if aliasing error occurs or not.