Determine the optimum thickness of enamel paint
Q: Briefly explain the thermal spray coating process (coating of metal with powder) with diagram…
A: Solution:
Q: Impregnation refers to which of the following; O None of the mentioned O O Something that should not…
A: To choose: The correct option. Explanation: Impregnation: The process which is used to improve the…
Q: Estimate how much silver is needed to make a four-piece setof silverware containing teaspoons,…
A:
Q: Please read the instructions carefully and do what are asks. Illustrate and show the COMPLETE…
A: GivenFN=70kipsallowable stress =MN=76kips
Q: A diesel component steel plate has a surface area of 200 in2 with a thickness of 0.002 in. Determine…
A: Given data as per the question Surface area of plate=200 in2=1290.32 cm2thickness =0.002 in=0.00508…
Q: Discuss the essential properties of the materials to manufacture frying pan.
A: following are the essential properties of the materials to manufacture frying pan-
Q: How does a small scratch or nick in glass reduce the tensile strength of the
A: stress concentration is defined as the phenomenon when the local stress value increases…
Q: Draw the diagram of Paint Spraying and also provide the ladder program.
A:
Q: A 2m? glass panel needs to be processing would you recor toughening is achieved.
A: Toughened glass has undergone processes of controlled thermal treatment (the process of heating and…
Q: the dark blue colour steel gun is shown below.
A: Plastic coating : Plastic Dip Coating is a process that involves immersing a preheated part into…
Q: 1- Which log is used to measure porosity accurately in oil and gas?
A:
Q: Please Explain this. Thank you
A: Assumptions For bernollis equation:- 1). Flow should be Ideal 2). Flow should be Laminar. 3). Flow…
Q: Explain with neat sketch of “Etching” the surface finishing process.
A:
Q: Filiform corrosion.
A: Filiform corrosion is a corrosion that occurs under some thin coating the form of randomly…
Q: Define the following and their test methods/procedures used in measuring the foam quality of…
A: Definitions and Methods to test following properties : Foaming Property (Foamability) :…
Q: Determine optimum thickness of enamel paint?
A: Given; Wire diameter is to be coat is=2 mm k=0.2 W/mKHeat transfer coefficient,h=200 W/m2K
Q: As shown in figure a Pepsi can and a plastic Pepsi bottle. Describe how they were manufactured
A: Pepsi can is produced using an ample material found in the world's covering. It happens normally in…
Q: Investigate and describe the different types of fluidization. Mention at least two examples of…
A: Fluidization : In the Fluidization process, The solids are caused to behave like a fluid in terms of…
Q: An injection molded polyethylene part has a dimension of 6.25 cm. A new material, polycarbonate, is…
A: Dimension of polyethylene part = 6.25 cm = 2.46 in
Q: a) Explain the functions of a plastic coatings.
A: given: as per our guidelines,I am given the answer of the first question. if you want to know the…
Q: hich is the correct property of ceramics? highly ductility Low strength stronger interatomic…
A: Ceramics are made with the mixture of some material like clay, earthen elements and water.
Q: Write or introduce the following topics of ceramics: • Types of ceramics • Sintering • Metal…
A:
Q: A metal term used to indicate that two or more layers of plastics (or metals) are pressed together…
A: LAMINATE OR LAMINATION is the term used to indicate that two or more layers of plastics or metals…
Q: (d) You are requested to design a display cylinder as shown in Figure 3. The cylinder needs to be…
A: Manufacturing process Manufacturing process are the steps in which is raw material is transformed in…
Q: Q2: Select any one casted component shown in the figure which is made up of alloy material and used…
A: I will select second one i.e spiral bevel gear. Alloys used in making gears is zinc alloys or…
Q: Write in detailed steps to select the right material for cooking ware
A: Steps to select the right material for cooking Ware
Q: What are the benifits of the Community, Students, Schools,Future Researcher in 3D printing using pet…
A:
Q: Silicone, aluminum, magnesium :and oxygen are
A: To find correct option
Q: 3.b. Explain with neat sketch, "Liquid plastisol dipping" surface coating process.
A: This process is used to form a thin layer of plastisol on the metallic surface with the help of…
Q: Explain the surface finishing operation in which stainless steel spoon is coated with silver.
A: The surface finish operation in which stainless steel spoon or cutlery is coated with expensive…
Q: Which of the following ways of filler metals is applied to the brazing operation; * Rod Powders…
A:
Q: Tabulate the different color-coded evacuated tubes, the additive/s present, and their uses.
A: A Vacutainer blood collection tube is a sterile glass or plastic tube with a seal that is evacuated…
Q: 5. Why does wax have a high freezing point?
A: Freezing point of wax is around 57 degree centigrade.
Q: Identify the correct ceramics that are used for the manufacturing of cutting tools from the…
A:
Q: QUESTION 5 Assuming a cylinder of molten plastics with a starting radius of 8.8mm and hieght of 1.8…
A: The cylinder of molten plastics with a starting radius of 8.8mm and hieght of 1.8 mm, what is the…
Q: Compare metals, polymers and ceramics on a chart or Table using the following properties and the…
A: Metal: A metal is an element that usually forms positive ions and metallic bonds. They have a…
Q: Plzz help
A: Given data; h=400 W/m2 Kk= 20 W/mKc=400 J/kgKρ=8500 kg/m3T(t) = 2980C Now; length of spherical…
Q: Cementing is the process by which cement slurry is placed in the annulus, bonding the casing to the…
A: Answer is b) True
Q: List three examples each of automobile components made up of steel and polymers.
A: there are so many components which are made up of steel (alloys of steel) and polymers.
Step by step
Solved in 3 steps
- A furnace wall is to consist in series of 7 in of kaolin firebrick, 6 in of kaolin insulating brick, and sufficientfireclay brick to reduce the heat loss to 100 Btu/ hr ft2 when the face temperatures are 1500 and 100°F,respectively.a) Show the figure of the systemb) What thickness of fireclay brick should be used?c) If an effective air gap of 1/8 in can be incorporated between the fireclay and insulating brick whenerecting the wall without impairing its structural support, what thickness of insulating brick will berequired?It is proposed to coat a 10mm diameter metal wire with enamel paint (k=0.1 W/m K) to increase heat transfer with air a maximum possible value. If the air side heat transfer coefficient is 1 kW/m2K, the optimum radius of enamel paint in mm should bePlot how hx (heat transfer coefficient) depends on the distance along a plate (x) and explain how this relationship .
- 2. You have a 2.5 m x 10 m, R- 18 effective wall, that includes a window that is 4 m by 2 m that is installed with a window to wall transition details having a linear heat loss coefficient of 0.43 W/m·K. What would the adjusted opaque wall RSI-value be if you include the thermal bridging impact of the window to wall transitionThe door of a 1 m long by 27.5 cm wide oven is made up of 2 AISI 1010 carbon steel plates of identical thickness and an 8 mm thick mineral fiber board with resin binder (intermediate plate) . the composite plate considering the three plates is 5 cm. The temperature on the inner wall of the oven is 172 ° C and the surface temperature on the oven door (outer wall) is 35 ° C. The oven door is exposed in a room where the ambient air temperature is 30 ° C. Do the following: Estimate the convective heat transfer coefficient associated with ambient air.The rear window of an automobile is defogged by pass- ing warm air over its inner surface. (a) If the warm air is at T ,i 40 C and the correspond- ing convection coefficient is hi 30 W/m2 K, what are the inner and outer surface temperatures of 4-mm-thick window glass, if the outside ambient air temperature is T ,o 10 C and the associated con- vection coefficient is ho 65 W/m2 K? In practice T ,o and ho vary according to weather conditions and car speed. For values of ho 2, 65, and 100 W/m2 K, compute and plot the inner and outer surface temperatures as a function of T ,o for –30 T ,o 0 C.
- You are designing a PCB laid horizontally on the ground. The PCB surface temperature can’t exceed 85℃ and has a size of 96mm x 90mm. Tinfinity = 45oC. "p" is the perimeter of the plate a) Calculate the Rayleigh number. b) If the PCB is laid hot-side UP, what is the Nusselt number and heat transfer coefficient? c) If the PCB is laid hot-side DOWN, what is the Nusselt number and heat transfer coefficient? d) Given your results from b and c, which one has better heat transfer? In that case, what is the maximum power dissipation the board can put out? Properties of Air:k = 0.025 W/mkPr = 0.72v = 1.847 x 10−5u = 16.84 x10−6p = 1.2 kg/m3B =1/ Tf (idwal gass)A steam turbine casing is made of a 6mm thick steel plate. At one location it has an inside surfacetemperature of 100°C. The convective heat transfer coefficient on the outside is 10 W/m2K. Theambient temperature is 25°C. What is the outer surface temperature? If the outer surface iscovered with a 3cm layer of insulation (k = 0.04 W mK), will it be safe to touch? Explain.Partially-frozen ice cream is being placed in a package before completion of the freezing process. The package has dimensions of 8 cm by 10 cm by 20 cm and is placed in air- blast freezing with convective heat coefficient of 50 W/(m2 K) for freezing. The product temperature is -5°C when placed in the package, and the air temperature is -25°C. The product density is 700 kg/m3, the thermal conductivity (frozen) is 1.2 W/(m K), and the specific heat of the frozen product is 1.9 kJ/(kg K). If the latent heat to be removed during blast freezing is 100 kJ/kg, estimate the freezing time.
- A flat isothermal computer chip has square cross-section of 1 cm x 1 cm, and is mounted on a board that insulates the chip on its sides and bottom. The top surface is exposed to a flowing coolant at 10°C, and corresponding convection coefficient h = 1000 W/m2·K. In order for the computer chip to safely operate, its temperature cannot exceed 65°C. What is the maximum allowable chip power?(a) If the cost of producing the hot water is $0.10 per kWh, what is the representative daily costof heat loss from an uninsulated pipe to the air per meter of pipe length? The convectionresistance associated with water flow in the pipe may be neglected.(b) Determine the savings associated with application of a 10-mm-thick coating of urethaneinsulation (k = 0.026 W/m-K) to the outer surface of the pipe.One end of a 0.3 m long steel rod is connected to a wall at 204°C. The other end is connected to a wall which is maintained at 93°C. Air is blown across the rod so that a heat transfer coefficient of 17 W/(m2 K) is maintained over the entire surface. If the diameter of the rod is 5 cm and the temperature of the air is 38°C, what is the net rate of heat loss to the air?