Need Solution through 15min Determine the pressure difference between points C and D.Take the specific weights to be Benzene: 8640 N/m2, Mercury:133100 N/m3Kerosene: 7885 N/m³, Water: 9790 N/m³, Air: 12 N/m³.WaterBenzeneAirDC50 cm19 cm30 cm|24 cm18 cmMercury-Kerosine

The pressure under hydrostatic condition is the normal force per unit area on the fluid element.…

Determine the pressure difference between points C and D. Take the specific weights to be Benzene: 8640 N/m3, Mercury:133100 N/m3 Kerosene: 7885 N/m³, Water: 9790 N/m³, Air: 12 N/m³. Water Benzene Air D 50 cm 19 cm C 30 cm 24 cm t18 cm Mercury- Kerosine

Determine the pressure difference between points C and D. Take the specific weights to be Benzene: 8640 N/m3, Mercury:133100 N/m3 Kerosene: 7885 N/m³, Water: 9790 N/m³, Air: 12 N/m³. Water Benzene Air D 50 cm 19 cm C 30 cm 24 cm t18 cm Mercury- Kerosine

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.119P: Determine the force F required to pull up the 3.54m stopper from the drain of a sink if the depth of...

See similar textbooks

Related questions

Q: A diver is 21m below the free surface of the sea. The barometric pressure is 101.000 kPa and SG is…

A: Answer: The pressure exerted on the diver at this depth is 45.185 psi.

Q: 2. a) Determine the resultant force acting on the inclined circular gate. b) Find the location of…

A: Given: Specific weight of water (ρg)=9810N/m3Diameter of the circular gate (D)=1mInclination of the…

Q: The initial pressures at A and B are the same at 103 kPa. If the pressure at the liquid at A (SG1 =…

Q: Determine the hydrostatic force and its location by (a)integration method and (b)formula method. 3m…

Q: Determine the pressure difference between points C and D. Take the specific weights to be Benzene:…

A: Given: Specific weight of benzene, wb=8640 N/m3 . Specific weight of mercury, wm=133100 N/m3 .…

Q: 46. Determine the absolute pressure required to lift the column of water from 2m depth. Assume…

Q: What is the hydrostatic force (kN) that acts on the Gate A-B? Given that the specific gravity of…

A: Total Hydrostatic force on a flat surface in any orientation is given by :- 》》 F = ρgx¯ A Where; ρ…

Q: Determine the new differential reading along the inclined leg of the mercury manometer of the figure…

Q: At 20 0 C, determine pressure (in N/m²) inside a water droplet having diameter of 1.5 mm with a…

Q: A simple U tube manometer is used to measure the pressure of oil flowing in a pipeline. Its left…

A: GivenC=59mmh=137mmS.Go=0.72S.Ghg=13.6

Q: If 3.9 m3 volume of water is displaced by an object, then the buoyant force acting on the object is…

A: Given V = 3.9 m3 Let the density of water is 1000 kg/m3

Q: y 1m 2 m 1 m

A: Vector is a physical quantity that has magnitude and direction both. Scalar is a physical quantity…

Q: Solve the hydrostatic force components of AB, BC, and CD using the general solution. Be sure to…

A: given; →DC=1m→AB=2.5m→CB=8m→density of water (ρ)=1000kg/m3

Q: Three liquids of different densities fill connected tubes as shown in the figure below (not drawn to…

Q: Determine the pressure difference between pipe A and B. 0.2 Water 0.3 Z4 Water 45 Z 0.45m Z3 0.675m…

A: Given data: z1=0.45 mz2=0.225 mz3=0.675 mz4=0.3 m Need to determine the pressure difference between…

Q: Determine the pressure (kPa) in the air space. Specific weight of water is 9.81 kN/m3. Reduce to 2…

Q: Determine the pressure difference between point A and B. pv = 1000 kg / m3 , pk = 13600 kg / m3…

Q: A cubic tank with a full capacity of 100 m^3 is filled halfway with oil (SG = 0.7). Determine the…

Q: A simple U tube manometer is used to measure the pressure of oil flowing in a pipeline. Its left…

A: As per our guidelines we are supposed to solve only 3 subparts if multiple subparts are asked .…

Q: Blood of specific gravity 1 flows through an artery in the neck of a giraffe from its heart to the…

Q: Determine the pressure difference between the points at A and B. Take the density of air as 0.03486…

Q: A U-tube manometer is connected to a closed tank as shown. The air pressure in the tank is 0.25 psi…

Q: Determine the pressure difference between points C and D. Take the specific weights to be Benzene:…

A: for the given arrangement ωbenzene = 8640 N/m3 ωmercury = 133100 N/m3 ωkerosene = 7885 N/m3 ωwater…

Q: If the plate is replaced with a vertical triangular plate (base = 5ft and height = 12ft) where its…

A: Dimension of the triangular plate,base, B=5 ftH=12 ftbase is submerged by 12 ft below the water…

Q: a).kN/m2. b) Head of water in meters,

Q: A tank contains mercury up to a height of 0.3 m over which water stands to a depth of 1 m and oil of…

Q: 2. Given the two compartment vessel as shown in the figure. Gage A reads 85 psig, gage B inside the…

A: GIVEN :- Pressure in gauge- A : PA=85 psig Pressure in gauge-B :PB=25 psig barometer reading :…

Q: Determine the pressure if the reading in a barometer shows 2.5 inches of Mercury. 8.65 kPa 1.23 psi…

Q: (i) the intensity of pressure in kPa at the interface between coconut oil & crude oil (ii) the…

Q: Question Q:- Determine the force exerted on the cone curved surface. The liquid in the tank has a…

A: Given data specific weight of liquid (γ) = 27kN/m3absolute pressure of the air (Pa) = 151 kPa…

Q: A diver is 27m below the free surface of the sea. The barometric pressure is 101.000 kPa and SG is…

Q: Y = 10 kN/m3 y = 20 kN/m3 50 cm 10 cm I. cm For the manometer shown, what is the gauge pressure at B…

A: The inclination:

Q: A simple U tube manometer is used to measure the pressure of oil flowing in a pipeline. Its left…

Q: etermine the hydrostatic force exerted by the water on the bottom an 3 ft 8 ft B 20 ft

A: Fluid Mechanics

Q: e. 235.87 What is the hydrostatic force (kN) that acts on the Gate A-B? Given that the specific…

Q: Determine the pressure of the water in Pipe A if the gage pressure of the air in the tank is 2 psi.…

Q: 10. Determine the magnitude of the hydrostatic force acting on gate AB, which has a width of 2 ft.…

A: Given:w=2 ftγw=62.4 lb/ft3

Q: Positions A-l are different points with respect to the atmospheric pressure as shown in the figure…

Q: 3.14 Determine the pressure p, in the bulb for the manometer readings shown. Oil (SG 0.85) 30 in.…

Q: 1 m Depth of Gate A-B is 6 m 4 m Liquid B 30

A: We know that Hydro-static force acting on the gate(F)=ρgAx

Q: absolute pressure in pa at a depyh of 6 m belowthe free surface when a barometer reads 760 mm…

Q: What is the hydrostatic force (kN) that acts on the Gate A-B? Given that the specific gravity of…

A: Given: The specific gravity of liquid, S = 8 The depth of gate, b = 6 m

Q: Calculate the manometer reading (x) if the upper manometer reading (y) is 400 mm Take the relative…

A: The pressure inside the container can be determined as,

Q: Determine the pressure difference between points C and D. Take the specific weights to be Benzene:…

Q: Define atmospherie, absolute and gauge pressure. Give the inter-relationship between them. A 6 m…

Q: Find the height of the portion of a cubic block that extends below the water surface (h) , the…

Q: 47. Determine the absolute pressure required to push the column of water to 2m height. Assume…

Q: A skin diver wants to determine the pressure exerted by the water on her body after a descent of 35…

Q: the steel is 9000 psi, determine the maximum safe pressure for the tank. (b) Compu the corresponding…

Question

Need Solution through 15min

Determine the pressure difference between points C and D.
Take the specific weights to be Benzene: 8640 N/m2, Mercury:133100 N/m3
Kerosene: 7885 N/m³, Water: 9790 N/m³, Air: 12 N/m³.
Water
Benzene
Air
D
C
50 cm
19 cm
30 cm
|24 cm
18 cm
Mercury-
Kerosine

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Basic:

VIEW

Calculation:

VIEW

Step by step

Solved in 2 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The 12-ft wide quarter-circular gate AB is hinged at A. Determine the contact force between the gate and the smooth surface at B due to water pressure acting on the gate. Use =62.4lb/ft3 for water.
Determine the volume of the concrete arch dam.
The cylindrical water tank with R = 10 ft and H = 1.6 ft has thin steel walls of uniform thickness and weighs 18000 lb when empty. Determine the depth of the water h for which the center of gravity G of the tank plus water will be located at the surface of the water. For water, use =62.4lb/ft3.
The weight of the cylindrical tank is negligible in comparison to the weight of water it contains (water weighs 62.4lb/ft3). The coefficient of static friction between the tank and the horizontal surface is s. (a) Assuming a full tank, find the smallest force P required to tip the tank, and the smallest s that would allow tipping to take place. (b) If the force P = 200 lb initiates tipping, determine the depth of water in the tank.
Determine the resultant force acting on the elbow of the thin-walled pipe when the pipe carries a uniform internal pressure p0.
Determine the force F required to pull up the 3.54m stopper from the drain of a sink if the depth of water is 10 in. Use =0.036lb/in.3 for water and neglect the weight of the chain.
Determine the smallest distance I) that would prevent the concrete dam from tipping about corner A. Use w=62.4lb/ft3 for water and c=150lb/ft3 for concrete.
The high-pressure water cock is rigidly attached to the support at D. Neglecting the weights of the members, draw the FBD of the entire assembly and count the unknowns.
Using integration, locate the centroid of the area under the n-th order parabola in terms of b, h, and n (n is a positive integer). (b) Check the result of part (a) with Table 8.1 for the case n = 2.
Find the elevation h (km) where the weight of an object is one-tenth its weight on the surface of the earth.
Each of the three gates has a constant width 1: (perpendicular to the paper). Calculate the force P required to maintain each gate in the position shown. Express your answers in terms of b, c, h, and (the weight density of the fluid).
Figure (a) shows the cross-sectional dimensions for the structural steel section known as C1020 (channel with a nominal depth of 10 in., weighing 201b/ft). The American Institute of Steel Construction Structural Steel Handbook lists the following properties for the cross section: A=5.88in.2,Ix=78.9in.4, and Iy=2.81in.4. If two of these channels are welded together as shown in Fig. (b), find Ix and Iy for the resulting cross section.