Determine the reactions at the supports and draw the bending moment diagram for the following structure. (Ans :θB =0.0354/EI, θC =-1.018/EI, Ay=12.483kN, MAB=- 10.388kNm, By=22.885kN, Cy=12.632kN)

Q: A traverse has the following data: LINE AB BC CD DE EA LENGTH 33.48 8.11 39.42 7.08 22.02 Use…

A: We have to compute for the linear error of closure and relative error of closure

Q: Answer the following questions since the two manometers shown in the figure are P A/P B = 4 in an…

A:

Q: 1- The spillway of a dam has a service life of 75 years. A risk of 5% for the failure of the…

A: Give data  Service life of the spillway = 75 years   n = 75 years  Risk of failure of structure = 5%…

Q: A nozzle is a device for increasing the velocity of a steadily flowing stream of fluid. At the inlet…

A: Specific enthalpy, velocity at exit and inlet. To determine : Velocity at nozzle exit. Since it is…

Q: D 04 m 0 0.3 0.6 m 0.2 m C If the shaft and plate rotates with a constant angular velocity of 5…

A: The angular velocity refers to how fast an object rotates or revolves relative to another point.…

Q: 1. Specifications on a job require a fill using borrow soil to be compacted to 95% of its standard…

A:

Q: C. A tsunami is a sea wave produced by an underwater earthouake. The height of a tsunami as it…

A:

Q: A beam (ABC) has a pin support at the left-hand edge (point A) and is supported by a thinner beam…

A: "Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: Referring to cast in place pile construction, produce a cause-and-effect analysis (fishbone)…

A: Cast in place pile construction- Cast-in-place pile construction involves inserting the reinforced…

Q: Anwer the question below: 1. Roles and Objectives of Structural Engineers 2. Different Structural…

A: Roles and objectives of Structural Engineers  Different Structural Elements Importance of codes and…

Q: The assembly consists of two brass rods AB and CD and one steel rod EF between a rigid bar. If the…

A: Horizontal displacement of end F of rod EF is, ∆=0.47 mm Material Length (mm) Diameter (mm)…

Q: Given the following data: Slump Requirement = 4" ements Max. Aggregate Size = 1.0" nts Water/cement…

A: Mass of cement = 350.91 kg/m3  Water/cement ratio = 0.55 Mass of coarse aggregate = 1072 kg/m3 Total…

Q: Given the following elements of a circular curve: middle ordinate = 2 m; length of long chord = 70…

A: Middle ordinate = 2m Length of long chord = 70 m Degree of curve = ?

Q: A rectangular "Apitong" beam 50mm x 250mm is used as a simply supported beam 3.2m long. Determine…

A:

Q: Determine the force in each member of the loaded truss. The forces are positive if in tension,…

A:

Q: EX/Determine the reaction at the support.Assume Ais Fixed B and c is rod = = FTITIT 4m 4m 2KW B ↓ 2m…

A: ###Reactions of Beam using force method of Analysis ( Castigliano's theorem)   Given- Length of rod…

Q: Q,28 A plane frame ABCDEFGH shown in figure has clamp support at A, hinge supports at G and H, axial…

A:

Q: 2-Force couples with an intensity of 100 N at the lowest level of the rigid body shaped to the side…

A:

Q: A Steel Cable used in a suspended roof system has an allowable tensile stress of 250 ksi.  It must…

A:

Q: metry for the jaws. 6 mm 12 mm G 35 24 20 mmmmmm 27 N -76 mm- B 27 N

A: An applied force is the force applied to an object by someone or something else. An object is…

Q: For the post-tensioned beam shown in the figure find the maximum usable moment capacity at midspan.…

A: material properties f'c= 5ksi,                                          fpu= 270 ksi,…

Q: A 6m simply supported beam AB carries 2 concentrated downward loads of P=60KN each placed at third…

A: EI = 21000 KNm2  Determine the slope at the left support A using Double Integration Method.

Q: Question # 2: The composite beam consists of a plates of steel. If the allowable bending stress for…

A:

Q: determine the tensile stress in each segment of the bar shown. Segment AB cross section 2in x 2in.…

A: Segment AB cross section 2in.×2in. Segment BC cross section with a dia. of 1.75in. Tensile load (P)…

Q: Determine the force P exerted on the twig G. Note that there is a horizontal line of symmetry for…

A: A tool which applies a load at twig G Line of symmetry exist for handle but not for jaws

Q: If the average run-off depth i è maximum run-off depth in a Om long and 40m wide, the a gation…

A: Given:- average run off depth = 80% L=400mm b=40m Irrigation current =10m3/min irrigation depth =…

Q: A steel rod of sectional area 25 sq. mm connects two parallel walls 5 m apart. The nuts at the ends…

A:

Q: Question 1 The velocity component in x and y direction are given by u= Axy-xy^²: v=x²y - 4y³. the…

A: The velocity component in x and y directions- u=λxy-xy2,&v=x2y-4y3.

Q: a. Find the moment of inertia of the section. b. Determine the moment capacity of the section. c.…

A: Wide flange: A =14000 mm4 d = 400 mm Ixx = 435 x 106 mm4 Iyy = 90.6 x 106 mm4 tw = 10 mm Fb = 138…

Q: a) Pressure acting on the vehicle door - b) Thrust force on the door = The vehicle, which flew into…

A: Height of Vehicle Door = 1.6 m Width = 1.5 m  It is 3 m below the free surface of the water

Q: 3) A beam carries uniformly distributed load of 60 kg/m rests on three supports spaced 1.2 m apart.…

A: Determine the overhange length (x) such that all support reaction shall be the same.

Q: Required information A garden hose attached with a nozzle is used to fill a 20-gal bucket. The inner…

A: The volume needed to fill a bucket = 20-gal The inner diameter of the hose = 1 in  The reduced…

Q: 4. A frame consists of four light, elastic vertical members and two rigid horizontal members, as…

A: m1=1350 kgm2=900kgnatural frequencies =4.91Hz and 12.05 HzExpressions for displacments…

Q: The body on the 30° incline is acted upon by a force P inclined at 20° with the horizontal. If P is…

A:

Q: The rigid beam shown is fixed to the top of the three posts made of steel and aluminum. The posts…

A: Thermal stress is defined as the stress that is created by the change in temperature value to a…

Q: The cross-sectional area of each member of the truss is 1000 mm². Calculate the stresses in the…

A: Cross sectional area of each section= 1000 mm2 To find Stress in member DF, CE, and BD.

Q: a) E is constant, find the reaction forces and moments. Using the Moment Distribution Method 1 = 300…

A: E = constant Determine the support reaction and moment using Moment Distribution Method.

Q: A simply supported steel beam ODD:9m EVEN: 8m long carries a uniformly distributed load of 21KN/m…

A: Span of simply supported beam = 9 m Uniformly distributed load = 21 kN/m Central concentrated load =…

Q: (a) Calculate the minimum flow velocities in sewers A and B. (b) At what minimum height above the…

A: Main sewer - A: Diameter of sewer = 750 mm Slope = 1% Discharge, Q=850 l/s Main sewer - B: Diameter…

Q: Given EI = 29x10^9 kN.mm^2, determine the following: 3 m 69 KN 30 kN/m 3 m 6 m 90 kN/m k = 10 kN/mm…

A:

Q: A steel strip is clamped at left end and supported by a spring at right end. The spring has a…

A: Length(L)=200mm I=bd312=5×10312=416.67mm4E=2×105N/mm2K=3 N/mm   To find  The deflection at right end…

Q: Draw a shear force diagram and bending moment diagram for a cantilever beam experiencing sine…

A: Given: Required : Shear force and bending moment diagram

Q: 7-4. Determine the equations of the elastic curve and specify the slope and deflection at B using…

A: Uniformly Distributed Load acting is 2 k/ ft on 8 ft span .

Q: 3) Determine the deflection at point C of the beam shown. E-200 GPa, I-250(106) mm*. Use the…

A: To find slope and deflection at C

Q: A rectangular beam having a width of 300 mm has an effective depth of 600 mm. Total depth of the…

A: As per our policy, the first two parts are solved within the stipulated time. Please post the…

Q: A simply supported beam of 2.4 metres span has a constant width of throughout its length with…

A: Supported by two supports and free to move horizontally, a simply supported beam rests on two…

Q: For beam with T section shown below calculate moment resistance and shear resistance and the maximum…

A: We know that Moment resistance for doubly reinforced beam is given by  ϕ.Mn =…

Q: Q3) A 2 mx 3 m spread footing placed at a depth of 1.75 m on a clayey sand soil with a unit weight…

A:

Q: A concrete pile with a rectangular shape with a base of 40 cm is built in saturated sand. Find the…

A: In order to calculate tension bearing capacity of the given pile using  β-method we have T = fs*Ap +…

Q: A W18 x 97 with Fy = 6 compression member. Compute the nominal s and Ku 1

A:

Equilibrium and Support Reactions

Civil engineers deal with structures that are composed of several members connected or with individual members such as beams and columns. To analyze such structures, the condition of statics must be applied. Under the static condition, the members are considered to be in equilibrium under the action of forces, that is, the members are assumed to be having negligible velocity.