Hi. Please help me with this one. You can use the 2nd photo as reference. Thank you very much.Subject: Theory of structures.SN= 66 Determine the ReactionsSN kN/mHinge3 mAB-4 m-2 m Determine the Reactions3 kN/m8 kNB.2 m2 m1.5 m2 m(a)B,6 kN8 kNB, B,-1m 1mB,2 m1.5 mC,(b)2 m6 kN8 kNB3.- C|1m 1 m2 m1.5 mC,AA,2 mA,2 MB (Righ)=0= 2C, – 6(1)=0C, =3kNEM,=0 =C,(1.5)+3(4)– 6(3)– 8(2) = 0C,=14.7kNE F;=0 = 4,-14.7 – 8(2) = 0A,=9.87KNEF, =0 = 4, +3-6-8(2)=0A,=9.4kN

Answered: Image /qna-images/answer/12592c3f-8050-4712-b2bf-85c5b5140f5e.jpg

Answered: Determine the Reactions SN kN/m Hinge 3…

Engineering

Civil Engineering

Determine the Reactions SN kN/m Hinge 3 m A B +3m 2 m te

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: BLEM 2: | 1500 lb 4500 lb • ft A E В |D 6 ft 6 ft + -3 ft→

Q: A certain engineering equipment is supported by the foundation shown in figure 3.49. The diameter of...

A: Given data Pin dia,= 25 mm Fy= 345 MPa

Q: Water is added to each jug and the pressure is measured right at the bottom of each jug. Rank the ju...

Q: Q3: A rigid beam ABCD is supported as shown. Initially and at room temperature the Seam is horizonta...

A: Given, Temperature = 120°C Length =3 m Steel wire , Are...

Q: In the structure shown below, the ratio of distribution factor of OA to that of OC is A I, L I, L I,...

A: For given arrangement, the ratio of distribution factor of OA to that of OC is

Q: Truss detail Member=9 Joint=6 Reaction=4 Is truss formed is stable

A: Introduction : The given problem is related with truss topic in solid mechanics . We are provided wi...

Q: A plate with width of 300 millimeters and thickness of 20 millimeters is to be connected to two plat...

A: We have to determine the value of maximum P that can be resisted by Tensile Stress considering failu...

Q: 1. Explain why the transportation planning process is not intended to furnish a decision or give a s...

A: Note- Hi! Thank you for the question As per the honor code, We’ll answer the first question since th...

Q: change of 1 in. in the level of the eSsure in pipe A does not change

A: consider initial condition pof the manometer pressure at chamber at X-X will be equal in...

Q: 10 ft 4 ft 4 ft 10 ft 10 ft B. 600 lb 800 lb

Q: In the structure shown below, the ratio of distribution factor of OA to that of OC is D A I, L I, L ...

Q: Question: Determine the kinetic energy of a 25.0 kg mass moving at 61.3 m/s.

Q: Estimate the Moment about the point A. Your answer is N.mm

A: Given data : The force at Point B (PB)=52 N The force at Point C (PC)=30 N The value of Force at poi...

Q: 4. Determine the maximum load P that can be applied in the system consisting of a bent bar bolted at...

A: Given data: dB=1/4 in. dw=7/8 in. t=3/8 in.

Q: Determine the Reactions 10 k 6 k В DO MN lb/ft 20 ft A 30 ft 15 ft - 10 ft- 10 ft-

A: To determine the reactions. The support reactions can be determined by applying the conditions of ...

Q: The two cars collide at right angles in the intersection of two icy roads. Car A has a mass of 1040 ...

A: Hello dear, this is the solution of your problem The problem is based on the principle of momentum c...

Q: 5. The position of a point during the interval of time from t= 0 to t = 6 sec is given by s=-0.5t + ...

Q: Show P/2k in terms of velocity discontinuities and shearing planes. Do not solve for the v continuit...

A: The discrete shear occurs along OA,OB,OC and OD.

Q: Mo 90 A 160 N/m Mo 380 N-m 200 N 4 m

Q: Enumerate and explain (in your own words) the limit states that should be considered

Q: Freight car A with a gross weight of 174000 lb is moving along the horizontal track in a switching y...

A: Given data, Weight of car A m1 = 174000 lb Velocity of car A v1 = 1.5 mph Weight of car B m2 = 15700...

Q: Determine the shear lag factor of the connection shown in the figure

A: Finding the shear lag factor =? Shear lag factor : It is defined as the non-uniform stress trans...

Q: Give and discuss some of the different applications of steel in structures and some important consid...

A: It has been asked in the question to discuss the different applications of steel in structures and s...

Q: PROBLEM THEORY-10. A 4-m propped cantilever beam is loaded as shown in the figure. E = 200 GPa and I...

Q: Explain the difference between a short column and a long/slender column in the context of structural...

A: We have to determine the difference between a short column and long or slender column in the context...

Q: Use the graphical method to construct the shear-force and bending-moment diagrams for the beam shown...

Q: Vertical Reaction at C in kN. Moment Reaction at C in kN-m.

Q: Determine the shear lag factor of the connection shown in the figure. W10 x 19 Answer:

Q: A 2.5 m span cantilever beam has a rectangular section and reinforcement as shown in Figure below. T...

Q: A concrete column with a circular hole is to be loaded in compression. a. What is the average comp...

Q: What is the main objective of conducting a transportation project evaluation?

A: The main objective of a transportation project evaluation is to furnish the appropriate information ...

Q: Exercise Problem 1: Find coordinates of the Centroid for the following figure:

A: Solution: We need to find the centroid in the given figure. We can divide the figure in 3 parts and ...

Q: - 1 attachment - 5. First ball is released from rest. After 2.5 seconds, second ball is released wit...

Q: An ASTM A992 WT6-section is to be used to resist a dead load of 310 kips and a live load of 425 kips...

Q: 2.51 Water, oil, and salt water fill a tube as shown in Fig. P2.51. Determine the pressure at point ...

A: Given,

Q: Determine the Reactions SN kN/m Hinge 3 m A B 2 m te

Q: What is the amount of usage in hours per year if initial cost of bulldozer is Php 25.5 M with operat...

Q: 2. Compare and contrast Ordinary Portland cement (OPC), Portland pozzolana cement and High alumina c...

Q: Akuminum rod E= 70 GPa G-26 GPa A 100 mm a=21,6 x10C A.Rod 20 KN 0.5m Beam ABC El=15O MNm в TEMPURAT...

A: A straight variation/extension happens in a wide range of shafts when it is presented to expanding t...

Q: The figure below are cables ( circular section) supporting a MN kN. Find the axial stress of each. T...

Q: The rocket sled starts from rest and accelerates at a = 30 + 2t m/s2 for the first 10 seconds. It th...

Q: Y 2"I X- 12" 2"| 4" 4" | 2"|

Q: Refer to the braced cut shown in the figure for which y= 20 kN/m², o'=23º, and c' = 0. 2.0000 The st...

Q: 1. Determine the diameter of the pin in the hinge support if the allowable shearing st pin is 400 MP...

Q: Problem 2.7 A reinforced concrete beam has the following data. Beam width, b= 300 mm Effective depth...

Q: In our generation, which technological advancement is NOT TRUE? * Technology has changed the way we ...

A: Brief concept- Technology- Technology is the application and the science which eases the work and mo...

Q: Below is a moment diagram of a certain beam. 2(m) 2(m) 2(m) 1(m) 2.96 3.32 Mx n=2 -2.4 -2.04 1. Dete...

Q: Situation 4 The girl always throws the toys at an angle of 30° from point A as shown. Determine the ...

Q: A 15" x 3/8" bar of A572 Gr. 50 steel is used as a tension member. It is connected to a gusset plate...

Question

Hi. Please help me with this one. You can use the 2nd photo as reference. Thank you very much.

Subject: Theory of structures.

SN= 66

Determine the Reactions
SN kN/m
Hinge
3 m
A
B
-4 m-
2 m

Determine the Reactions
3 kN/m
8 kN
B.
2 m
2 m
1.5 m
2 m
(a)
B,
6 kN
8 kN
B, B,-
1m 1m
B,
2 m
1.5 m
C,
(b)
2 m
6 kN
8 kN
B
3.
- C
|1m 1 m
2 m
1.5 m
C,
A
A,
2 m
A,
2 MB (Righ)=0= 2C, – 6(1)=0
C, =3kN
EM,=0 =C,(1.5)+3(4)– 6(3)– 8(2) = 0
C,=14.7kN
E F;=0 = 4,-14.7 – 8(2) = 0
A,=9.87KN
EF, =0 = 4, +3-6-8(2)=0
A,=9.4kN

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Initial concept

VIEW

Draw Free body diagram

VIEW

Apply equations of equilibrium

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Two beams at 6 meters in length each are arranged so that the reactions at A, B, and D are the equal. The two beams are connected by an internal roller connection. Determine the equal reaction at A, B, and D. a. 180kN b. 120kN c. 160kN d. 240kN
Also each pin reaction
Determine the Reaction R4 in KN.0
compute the reaction at supports.
Two circular shafts are joined together between fixed supports to resist a torsional moment of 80 kN-m as shown. Determine the absolute value of the reaction at the left support in kN-m ( COMPLETE SOLUTION NO ROUNDING OFF)
force@ D=40kips. I have provided the reactions. Pls continue Asap. Thanks. Use moment distribustion method
Determine the reaction at support A and B?
Find the reaction in hinge A and roller C
Compute the support reaction
Determine the reaction at A if w =21 kN/m, L =5
Determine the horizontal and vertical components of the reaction at the pin Aand the reaction of the rocker B on the beam. Note that the roller support at B has an inclined axisby which the reactionary force will act through
Determine the reactions at the fixed support A and the roller B. Support B settles 2 mm. E = 200 GPa, I = 65.0(10-6) m4.