Start your trial now! First week only $4.99!*arrow_forward*

Question

Determine the resultant of the force system. Indicate where the line of action of the

resultant intersects the line AB.

Tagged in

Engineering

Mechanical Engineering

Find answers to questions asked by students like you.

Q: Wind at 20°C and 1 atm blows at 75 km/h past a flagpole18 m high and 20 cm in diameter. The drag coe...

A: Given data

Q: How can we calculate the maximum stress?

A: Stress: Stress is defined as the developed force in the specimen per unit area when that specimen is...

Q: A gas is contained in a vertical, frictionless piston– cylinder device. The piston has a mass of 3.2...

A: Given: The mass of the piston is M=3.2 kg. The cross-sectional area of the piston is A=35 cm2. The f...

Q: 3-10. A balloon is released into the air from the origin and carried along by the wind, which blows ...

A: Given Data: The x-component of velocity is u = 0.5 m/s. The y-component of velocity is v = 0.8+0.6y...

Q: Question 3 What defines a pathline? DAll of the fluid particles from the same origin The lines drawn...

A: Path lines: Path lines represents the actual path travelled by the particle. When a particle moves a...

Q: 4-26. The cart supports the uniform crate having a mass of 85 kg. Determine the vertical reactions o...

A: Write the expression of the moment about AB.

Q: QUESTION 10 This question is about springs and oscillations. A mass of 10 kg is attached to two spri...

A: Click to see the answer

Q: 7-17 A crate weighing 4000 lb is attached by light, inex- tensible cables to the truss of Fig. P7-17...

A: Click to see the answer

Q: Determine the value of θ corresponding to the equilibrium position of the rod of Prob. 10.10 when I=...

A: The force and dimensional geometry of slender rod can be modified as follows,

Q: it's very urgent.

A: Draw the diagram replacing the UVL with point load.

Q: Air, assumed to be an ideal gas with k = 1.40, fl ows isentropicallythrough a nozzle. At section 1, ...

A: Given data: The temperature at the section 2 is, T2 = -50 0 The ratio of specific heat is, k = 1.40...

Q: h = 4m

A: Click to see the answer

Q: In Prob. 3.24, determine the perpendicular distance from point B to wire AE.(Reference to Problem 3....

A: Coordinates A (-90, 160, 0) E (120, 0, 120) Unit vector AE can be determined as

Q: 21-55. The 20-kg disk is spinning on its axle at w, = 30 rad/s, while the forked rod is turning at w...

A: Given Angular velocity of disk = 30 rad/s Precision angular velocity = 6 rad/s Moment of inertia of ...

Q: The rod ABC is made of an aluminum for which E5 70 GPa. Know-ing that P5 6 kN and Q542 kN, determine...

A: a) Deflection at A can be determined as

Q: For a geothermal power plant, the underground hot water thetemperature of 80oC is the source, and th...

A: Click to see the answer

Q: F16-23. At the instant shown, the wheel rotates with an angular velocity of w = 12 rad/s and an angu...

A: Given that,

Q: Define the term deflection?

A: Whenever loads are applied to the object: It can deform depends on the loading condition.

Q: 3-3 A homogeneous cylinder weighing 500 lb rests against two smooth planes that form a trough as sho...

A: Click to see the answer

Q: If the direction of the resultant force acting on theeyebolt is defined by the unit vector uFR = cos...

A: The force vector of force F1, The force vector of force F2, The force vector of force F3,

Q: The truck is used to pull the heavy container. To be most effective at providing traction to the rea...

A: The container is better positioned where it is currently placed because the effective centre of mass...

Q: The volume flow rate of liquid refrigerant-134a at 10°F (? = 83.31 lbm/ft3) is to be measured with a...

A: Given Data: The density of the refrigerant is ρ = 83.31 lbm/ft3. The inlet diameter is D1 = 6 in. T...

Q: Technical sketching is only appropriate for fine detail work near the conclusion ot the design proce...

A: The technical drawing is a tool to share the ideas and thoughts among the engineers. Technical sketc...

Q: R12–11. Two planes, A and B, are flying at the same altitude. If their velocities are vA = 600 km/h ...

A: Given data as per question Velocity of plane A =600 km/hr Velocity of plane B = 500 km/hr Angle =750

Q: A spherical tank is designed to be filled with gasoline (SGgasoline = 0.75). If the allowable maximu...

A: Write the expression of the density of the gasoline. Write the expression of the pressure. Write t...

Q: A composite has 20 vol% fibres with E = 150 GPa in a matrix Em = 30 GPa. The matrix fails first at a...

A: The given problem belongs to composite materials, and in the composites if either the matrix or the ...

Q: Write the primary dimensions of each of the following variables from the field of solid mechanics, s...

A: Part (a) Moment of inertia (I) can be expressed as, Where, ri is the perpendicular distance of the ...

Q: Determine the reactions at the journal bearing supports A, B, and C of the shaft, then draw the shea...

A: Given Weight pulley 1 = 400 N Weight pulley 2 = 400 N Support bearing A, B, C To find Shear force an...

Q: A 16-lb wooden panel is suspended from a pin support at A and is initially at rest. A 4-lb metal sph...

A: Write the expression of the moment of inertia of the plate. Write the expression of the velocity of...

Q: At what height h above its center G should a billiard ball of radius r be struck horizontally by a c...

A: Consider the billiard stick exert the force P for the time interval Δt. So the external impulse is P...

Q: A vertical piston-cylinder device contains a gas at a pressure of 105 kPa absolute. The piston has a...

A: Click to see the answer

Q: What is restitution impulse?

A: Fig.1 Consider two bodies A and B of mass M as shown in Fig.1. When body A strikes to body B, a ...

Q: The A-36 steel tubular shaft is 2 m long and has an outer diameter of 50 mm. When it is rotating at ...

A: Given data as per question Length of tubular shaft = 2 m Outer diameter = 50 mm Power transmission =...

Q: Represent each of the following combinations of units in the correct SI form: (a) Mg/ms, (b) N/mm, (...

A: The conversion of the units can be given as, Part (a) Mg/ms Here, m is for meters and s is for secon...

Q: Determine the length of the common perpendicular between the cableBH and the line AD.

A: The problem is to determine the perpendicular distance between the wire BH and distance AD. For this...

Q: A new temperature scale, "W is desired with freezing of water at 24°W and boiling point at atmospher...

A: Given is Freezing pt. of water (in oC) = 0oC Freezing pt. of water (in oW) = 24oW Boiling pt. of wa...

Q: 12-45. The nails are on both sides of the beam and each can resist a shear of 2 kN. In addition to t...

A: Draw the free body diagram for the given problem. Now determine the centroid of the given system. ...

Q: Consider a large furnace that can transfer heat at a temperature of 2000 R at a steady rate of 3000 ...

A: Write the given data:

Q: Explain how macroscopic plasticity in metals occurs from the point of view of microscopic mechanisms...

A: Macroscopic plastic deformation simply corresponds to permanent deformation that results from the mo...

Q: Three steel rods (E5 29 3 106 psi) support an 8.5-kip load P. Each of the rods AB and CD has a 0.32-...

A: Given: The modulus of the elasticity of the steel, E = 19.3x10^3 Psi The magnitude of load, P = 8.5 ...

Q: An inventor claims to have developed an engine that takes in 25 kJ/s at a temperature of 400 K, and ...

A: Given data: The input heat is, Qi = 25 kJ/s. The rejected heat is, Qr = 10 kJ/s. The temperature of...

Q: The weight of bodies my change somewhat from one location to another as a result of the variation of...

A: Given data as per the question weight of person = 160 lbm Elevation at Denver = 1610 m Elevation at ...

Q: A. Specify the resultant force location from B B. Calculate the magnitude of the resultant force of ...

A: Click to see the answer

Q: 4 decimal places final answer

A: weight of the person = 160 lbm

Q: If mercury (SGH = 13.6) is used in a barometer measuring atmospheric pressure of 97 kPa. What is the...

A: Click to see the answer

Q: A func tion f is given. cos x f(x) = Notice that f(x) is not defined when x = 0. What happens as x a...

A: Given Data: The given function is f(x) = (1-cosx)/ At x = 0 the function takes the 0/0 form which ...

Q: Solve please

A: Related to coefficient of friction various laws have been given by great researchers such as: Leona...

Q: 14-79. A 2-lb block rests on the smooth semicylindrical surface at A. An elastic cord having a stiff...

A: Given data as per question Weight of the block = 2 lb Stiffness = 2 lb/ft Angle = 450

Q: A completely reversible refrigerator is driven by a 10-kW compressor and operates with thermal energ...

A: Given Data: The work input is: W=10 kW The temperature of the cold reservoir is: TC=250 K The tempe...

Q: Can a shock wave develop in the converging section of a converging–diverging nozzle? Explain.

A: In order to produce a shock wave, the flow must be a supersonic flow. Supersonic flow: The velocity...