Determine the shear force V in the beam at the point located 0.75 m to the right of point B. The ground reactions are provided. 2 kN/m 3 m 4.70 KN 8.16 KN O 9.50 KN 4.90 KN O 6.95 KN O 7.34 KN B 5 kN/m 5 m 14.30 kN C

Determine the shear force V in the beam at the point located 0.75 m to the right of point B. The ground reactions are provided. 2 kN/m 3 m 4.70 KN 8.16 KN O 9.50 KN 4.90 KN O 6.95 KN O 7.34 KN B 5 kN/m 5 m 14.30 kN C

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Determine the cracking moment in kip-ft for the section shown if: f'c = 4000psi and f₁=7.5√f'c. 9…

A: Given:- The compressive strength of the concrete = 4000 psi The steel reinforcement provided = 3-#10…

Q: 2-13. The pelvis P is connected to the femur F at A using three different muscles, which exert the…

A: Given,

Q: A steel gear, with 80-mm diameter ro d connected to it is used to transmit 600 HP at 200 rpm. The…

A: Given Data Diameter of rod (D) = 80 mm Power transmit (P) = 600 HP Revolution (N) = 200 rpm…

Q: A Im wide rectangular channel has a bed slope of 0.0016 and the Manning's roughness coefficient is…

Q: Compute the safest minimum diameter of th e cables if the allowable axial stress of the c able is…

Q: The Pertamina Energy Tower - A Primer on Green Skyscraper Design What are the components of a…

A: 1. The elements that give a vertical city its ability to operate like an ecosystem that can maintain…

Q: Problem 1: A rectangular beam having b - 250 mm and d = 450 mm spans 4.5 m face to face of simple…

A: Beam Design for shear

Q: 1) A 12 hour rainfall with uniform intensity of 4 cm/hr produces a storm hydrograph of peak…

Q: Compute the effective stack height of a coal burning power plant with physical stack height of 200 m…

Q: Find out the amount of soil required to be excavated from a borrow pit in cubic meter. If the voids…

A: Given- Void ratio of borrow pit=1.4 volume of fill=150000 cum void ratio of fill=0.8

Q: A 16 mm thick plate measuring 650 mm x 420 mm is used as a base plate for an ISHB 300 column…

A: Given information, Thickness = 16 mm Area of plate = 650 x 420 mm² Factored compressive force =…

Q: The beam shown in the figure carries distributed I oads. Design the square (a x a) cross-section of…

Q: The following are given for a specimen of soil: M = 300 g, Msolid = 170 g, Gs = 2.72 and S = 70%.…

Q: 2- Find the force in each member of the truss shown below 10 kips B G 3@8'-24' F D 8 kips, E 6'

A: Given: Required : Force in each member of truss

Q: 20 KN B 6 m 12 m 15 KN to 2 kN/m 30 m 18 m D 8 m 30 KN E

Q: Determine the moments of inertia about the y-axis of the circular area without and with the central…

A: To find moment of inertia about y axis

Q: Q- The velocity of water at the outer edge of a 60cm diameter whirlpool, where the water level is…

A: Given- Diameter of whirlpool D=60 cm Velocity of water at horizontal water level V=2.5 m/s It is…

Q: Draw axial, shear & moment diagram for the frame shown below ? 15 kNm 12 kNim с A 10m B 5m 6m 3m

A: Given data:

Q: 2. In general order of importance, the senses most used by drivers are (eyes) 8. For a driver in a…

Q: a. Compute the vertical deflection at midspan due to flexural deformations only. b. Compute the…

Q: Problem 1: A rectangular beam having b = 250 mm and d = 450 mm spans 4.5 m face to face of simple…

A: Given: b = 250 mm d = 450 mm L = 4.5 m DL = 17.5 kN/m LL = 50 kN/m fc = 28 MPa fy = 420 MPa

Q: Situation 1: For the beam whose cross-section is shown, f'c = 17.25 MPa, fy = 420 MPa. Determine the…

Q: The beam in Fig 5-1. is used to support a dead load "self weight of 0.8 kN/m, a live load 4 kN/m,…

Q: 1. The velocity of a particle is given by v = 25t² - 80t - 200, where v is in feet per second and t…

A: The acceleration is obtained by successive differentiation of v with respect to the time. Thus,a=…

Q: Assume a constant value of EI = 560×10° N-mm² for the beam. A 210 N-m 200 mm Determine the…

Q: Determine the cracking moment in kN-m for the section shown if: f'c = 28MPa and fr=0.7√f'c. 600 mm 2…

Q: 4 For a rectangular channel, if the Froude number = 1.5 and the initial depth=0.8 m, the depth after…

Q: For Fig. Water flows through a pipe at rate of 350 L/S. The Pipe consists of two sections of…

Q: Find level of service (LOS) for an old freeway in Basrah city with the following characteristics:…

A: Given:- The free flow speed (FFS) = 65 mi/hr The peak hour factor (PHF) = 0.80 The number of lanes…

Q: A solid shaft transmits 250 kW at 100 rpm. If the shear stress is not to exceed 75 N/mm², what…

Q: Question- A 5m high vertical earth retaining wall retains a dry granular backfill with angle of…

Q: 1. A steel column has an unsupported height of 5.4 m is pin connected at both ends with sidesway is…

A: L= 5.4 m P=530 kN Top Mx= 20 kN-m My= 3 kN-m Bottom Mx= 13.5 kN-m My= 1 kN-m Fy =250 kN To check -…

Q: A 7 kips/ft 11 ft E = 29000 ksi 1 = 984 in4 Determine the beam deflection at B. Answer in inch…

A: Given Data E = 29000 ksi I = 984 in4 Find the deflection at B.

Q: Question 5 Figure 5 shows a header tank in a laboratory. a) Determine the discharge when filling the…

A: Given, Pipe diameter AC = 22 mm Pipe diameter BC = 100 mm Pressure head at B = 35 m

Q: Q2) Fill the following blanks with suitable word(s): 16 1. The various types of heat-treating…

A: Reference : Construction Materials, Steel Heat treating process. Given : Two statements about steel…

Q: E= 29000ksi 1=291 in4 6 ft ↓↓↓ B Determine the deflection of the beam at midspan. Answer in inches…

Q: Question No. In an aquifer extending over 150 hectare, the water table was 20 m below ground level.…

A: Given data- An aquifer- Area A=150 ha, Initial depth of water table from ground level=20 m, Final…

Q: Situation 2: Determine the ultimate moment capacity of the reinforced concrete beam if it is…

Q: The major and minor principal stresses at a point are 3 MPa and -3 MPa respectively. The maximum…

A: Given: The major principal stress, σ1 = 3 MPa The minor principal stress, σ2 = -3 MPa

Q: Question- A 5m high vertical earth retaining wall retains a dry granular backfill with angle of…

Q: Torsion A square beam of size 400 mm x 400 mm is subjected to a factored bending moment and twisting…

Q: A Im wide rectangular channel has a bed slope of 0.0016 and the Manning's roughness coefficient is…

Q: What is the approximate value of the tensile strength governec the cross section of a roof truss…

Q: (e) 88 (f) (g)

Q: Analyze the following beams by computing the support reactions. EI is assumed to be constant.

A: Given: Required : Analyze the structure

Q: Assume the section has cracked and use the transformed-area method to compute the required…

Q: INUTO: Tom C] Draw the shear force V and bending moment M diagrams for the frame showr - Te

A: Given:- To find:- Shear force and bending moment diagram Concept:- Shear force diagram displays the…

Q: Question 5: For system shown below, estimate: 1. The head, flow rate, and efficiency in case of…

A: Given, Pump curves for certain flow system

Q: A company that manufactures pulse Doppler insertion flow meters uses the Straight Line method for…

A: An asset's book value is its value as expressed by the balance in its balance sheet account. Asset…

Q: Write (dynamic viscosity, kinematic Viscosity, Specific gravity, Bulk Modules of Elasticity) in MLT…

A: Required : Express dynamic viscosity, kinematic viscosity, specific gravity and bulk modulus of…

Question

Kindly answe this. Thank yoouuu!!

Determine the shear force V in the beam at the point located 0.75 m to the right of point B. The ground reactions are provided.
2 kN/m
3 m
4.70 KN
8.16 KN
O 9.50 KN
4.90 KN
O 6.95 KN
O 7.34 KN
B
5 kN/m
5 m
14.30 kN
C

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

For the beam and loading shown below (L = 2.4 m, E = 200 GPa, I = 1000 mm4 and w = 30 kN/m), find (a) TThe slope at point D.(b) The reaction force at end A
Determine the shear value (kN) when x = 2.2m from the left side of the beam where: L = 4.9 m; Wo = 131 kN/m
For Beam 3, what is the vertical reaction at B?
Determine the magnitude of F so that the resultant couple moment acting on the beam is 1.5 kN.m clockwise ?
If P = 20.3 and M = 6.83, Determine the Shear Force at point B of the Beam shown.
A force F = (0.5i – 2.0j + 7.0k) kN acting at A(5, -4, 0)m about axis BC where B(6, 8, 4)m and C(-6, -5, 8)m. What is the perpendicular distance between F and the axis BC in meters?
Calculate the critical shear Vu in kN.0
Draw the free-body diagram of the beam. If F=4 KN, what are the reactions at A and B?
Calculate the shear at right end of span BC in kN.0
Draw the normal force, shear force and moment diagram of the structure AB = 2 m, BC = 1 m, CD = DE = 2 m
The horizontal component for the 60 kN force is? a. 51.96 kN b. 45.94 kN c. 55.96 kN d. 35.96 kN The vertical component for the 60 kN force is? a. 20 kN b. 25 kN c. 30 kN d. 35 kN
Define the forces affecting to beam CDB when P = 600 N